Search Documents

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By George A. Mealey

Caving mining methods that are based on a planned caving of rock above and/or at times surrounding the material being mined can be classified in three broad categories: longwall mining, sublevel caving, and block caving. Each of the three methods involves a distinct technology as well as art of operation. Each requires a relatively large, regular, and predictable ore body. As a rule, the effect of mining results in some form of impact or change on the surface. Operationally, underground caving methods are characterized by high productivity as well as a high percentage of extraction of the mineral being mined. A key element for the productivity of this form of mining is the ability to standardize the various elements of work taking place underground. Therefore, work-men may perform a specialized role rather than function as all-around miners. Further, the nature of the mining methods lend them to a high level of mechanization. Operations and manpower can be centralized into a relatively small area where supervision can be concentrated and therefore be more effective. Productivity as well as safety benefits thereby. The caving method is unique in that the exploitation openings are deliberately destroyed by the process of mining. Rock mechanics principles focus on the ensurance and the propagation of the cave as well as the continuance of the mine openings designed to extract the broken ore. As a rule, production operations are designed to maintain a steady, continuous flow of ore from the extraction areas. This steady flow rather than an intermittent flow tends to promote good caving action as well as reduce hangups.

Jan 1, 2008

By Ting Ren, Lihai Tan, Alex Remennikov, Xiaohan Yang, Xueqiu He

"Due to recent coal bursts in Australian coalmines, research of coal bursts has attracted intensive interest from mining researchers and engineers worldwide. Previous research has shown that the sudden drop of fractal dimension may be a precursor of catastrophic failure of rock. This paper examines the fractal characteristics of temporal-spatial distribution of acoustic emission signals released during the compression loading process of coal. This research suggests the possibility of coal burst forecasting based on acoustic emission data. The concept and calculation equation of fractal dimension is introduced in this paper. Additionally, uniaxial compression experiments of Australian coal samples are conducted, and the acoustic emission waveform and 3D location are recorded simultaneously by eight sensors Express-8 AE monitoring equipment in the loading process. The experimental results indicate that the continued slowdown of fractal dimension in time sequence can be used as a precursory signal of coal sample brittle failure. The fractal dimension of the spatial distribution of acoustic emission events decreases with the evolution of coal fracturing.INTRODUCTIONCoal bursts refer to the catastrophic failure of overstressed coal subject to the dynamic and static loads. In recent years, coal bursts have occurred in major coal mining countries and this phenomenon has attracted the research interests of international mining and geotechnical scholars. A total of five coal burst accidents happened in Australian coalmines since 2014. On October 20, 2018, a coal burst occurred at Longyun Coalmine in China’s Shandong province, which led to 21 fatalities. Unfortunately, even after decades of research, it seems neither more accurate forecasting methods nor comprehensive controlling measures put forward by researchers have solved the problems posed by coal bursts.As an instantons energy releasing process, coal bursts are always associated with energy dissipation in the forms of acoustic emission, micro seismicity, and electromagnetic radiation (Yamada, Masuda, and Mizutani, 1989). It is believed by many researchers that the frequency–magnitude relationship of micro seismicity induced by rock failure satisfies Gutenberg-Richer relationship as well (Feng et al., 2017). Hence, based on the principal and theory of earthquake source locating, micro-seismicity monitoring equipment has been adopted in many coalmines to locate seismic event origins associated with coal and rock failure in an attempt to better forecast coal and rock bursts. Although many parameters such as b value (parameter of Gutenberg and Richter’s law) (Lu et al., 2015) have been adopted as indicators of risk, the forecasting of coal bursts is still of low accuracy. The same is true with earthquake prediction, as it remains as a worldwide problem even after decades of research and practice. Acoustic emission (AE) methods are now widely adopted to detect rock failure processes under an applied stress for application predicting the abrupt failure of rock in the laboratory (Li et al., 2017). Previous studies have found that significant overlap exists between research regarding AE and micro seismicity with respect to generation process (both are concerned with the generation and propagation of elastic wave) and event origin location, as geophysical signals of both are same (Lockner, 1993). That is, the frequency–magnitude relationship and early-warning indicators found by AE research in the laboratory have a potential applicability to in-field micro seismic monitoring of coal bursts. Through experimental study, Feng and Seto found that the temporal distribution of acoustic emission counts of rock have distinct fractal structures during load-increase processes (Feng and Seto, 1999). Landis and Lucie found good correlation between fracture energy and AE energy during testing of mortar specimens as well (Landis and Lucie, 2002). Based on preliminary experimental study, many schol"

Jan 1, 2019

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By Phil Shelton

What exactly does clean coal mean? Mining coal creates dust and releases methane gas. And burning coal liberates CO2 and emits particulates, including SO2 and NOx. Coal creates wastes that are often stored in unsightly and potentially dangerous slag heaps and lagoons. When clean coal technology is discussed, it sometimes seems that creating modern or ?ultra super critical? coal-fired power stations is presented as the main or even the only answer. However, there may be a more holistic approach. Using the energy potential of coal is always going to have environmental impacts. Some of these will be negative. But the need to secure future energy resources demands that society tackle these negative issues and find ways to minimize and offset them.

Jan 1, 2010

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design and operation from ground movement data can be utilized in underground mines. Communicating the information and exploring new findings can be a challenge, however, in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as they are multidimensional, depending on the space and the rate at which they take place. To tackle this challenge, geotechnical engineers should focus on using simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a trigger action and response plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study was conducted at the East Decline of the San Xavier (SX) Underground Mine, a laboratory mine operated by the University of Arizona. The project aims to produce visualizations that optimize the use of geotechnical data in near-real time.

Sep 1, 2025

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By Bill Tucker, Mike Black

"PROJECT OVERVIEW Crossrail, Europe’s largest construction project, will increase London’s transportation capacity by 10% when it opens in 2018. The Crossrail scheme is a combination of surface and underground railway that stretches 118km east-west through central London from Reading, Berkshire and Heathrow airport in the west to Shenfield, Essex and Abbey Wood in the London Boroughs of Greenwich and Bexley in the east. Crossrail will serve 40 stations, ten of which are new, and bring 1.5 million people within 45 minutes commuting distance of London’s key central business districts. 21km of the Crossrail route comprises twin-tunnels beneath the heart of central London. It is the central section of the route, and the challenges that had to be overcome to construct its tunnels under the historic capital that forms the subject of this paper. The route of the Crossrail tunnels can be seen in Figure 1. These tunnels weave their way through the city’s underground landscape, linking eight new underground stations which connect to the existing London Underground network, providing interchanges with nine existing lines as well as the National Rail and Docklands Light Railway networks.Crossrail began construction of enabling works in May 2009 and launched the first of eight tunnel boring machines (TBMs) in May 2012. 42km of major tunneling work was completed in May 2015, and included 11km of sprayed concrete lined tunnels at the five mined stations (Bond Street, Tottenham Court Road, Farringdon, Liverpool Street and Whitechapel) in addition to the bored tunnel sections. The remaining three sub-surface stations at Paddington, Canary Wharf and Woolwich were constructed as large open boxes prior to the TBMs passing through. Crossrail, Ltd. is a special purpose company formed by the project’s joint sponsors, Transport for London and the Department for Transport, to manage design, construction and commissioning of the project. In 2009, Crossrail engaged Bechtel Ltd. as its delivery partner and a joint venture, Transcend (comprised of CH2M, AECOM and the Nichols Group), as its programme partner. The project is being managed by an integrated programme management team which is staffed by Crossrail and its partners. The railway, when opened, will be operated by Rail for London. With tunneling completed in accordance with the project’s master control schedule, the new railway is scheduled to commence dynamic testing in late 2017, with a phased opening of the tunneled sections and stations through Central London in 2018."

Jan 1, 2016

By Ahmad Rahbar-Kelishami, Zahra Karimi

When alumina is extracted from bauxite ore, one of the environmental pollutants created is known as red mud (RM). This study clarifies that the RM obtained from the Iran Alumina Company has a significant proportion of iron oxides (24%), alumina (19%), silica (17%), and calcium (21%), as well as trace amounts of other minerals. The elements in the RM can be removed and utilized again to reduce environmental pollution. Acid leaching is one of the best ways to selectively exclude some minerals from the RM. In this research, the RM is exposed to different inorganic acids, including HCl, HNO3, H2SO4, and H3PO4, and their binary mixtures. By comparing the results obtained from XRD, EDX, and SEM, it was discovered that CaSO4 crystals are formed by exposing the RM to sulfuric acid. Besides, phosphoric acid was only able to destroy the surface of RM particles. The XRD analyses of acid-washed residues demonstrated that except for the residue of HCl 5 N, all residues contain hematite, showing that inorganic acids cannot easily extract hematite from the complex phases of red mud. While the dissolution of RM with HCl or HNO3 will remove most of the calcium content of RM texture, increasing its iron oxide percentage, which may subsequently be utilized to make colors and pigments.

Mar 29, 2024

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

What is your assessment of the status of the mining industry as we see some evidence of an economic recovery? I am optimistic about the short and midterm prospects for the industry and, hence, for the professionals in the industry that constitute the majority of the SME membership. All who will read this interview recognize that the quality of life we enjoy today is largely a result of our achievements in the mining and minerals processing sectors. I believe that the sustainability of that quality of life and the aspirations of other sectors of the global community to attain that same lifestyle will significantly depend on the continued successes of these industries. Looking at some of the traditional economic indicators, we see predictions of continued increases in gold prices during the next 12 months as a new round of quantitative easing keeps real interest rates low and drives excess capital flows from countries with trade surpluses - who have traditionally parked their money in U.S. government bonds - into other investable assets, such as gold. On the fuel side of the industry, we have during the last decade seen a steady rise in the cost of coal, and some of the recent spot prices have seen dramatic increases. Some suggest that coal prices may rise sooner than anyone expects, as global reserves are revised downward. This is based on the hypothesis that some of the main coal-producing countries are overestimating supplies and that coal prices could start rising far sooner than anyone thinks - with obvious serious implications for energy policy. Those forecasters note that, for the past couple of decades, global supply has been dropping at a faster rate than consumption.

Jan 1, 2011

By P. D. Chamberlain

Agglomeration for the heap leaching of gold and silver ores is the process of attaching fine ore particles-less than 150 µm (100 mesh)-to coarser particles. The fines are thus immobilized and uniformly distributed throughout the heap. This is needed to make heaps more porous and uniformly permeable to the flow of a leaching solution. This article describes liquids and binders used to form agglomerates. Agglomeration techniques and equipment are also described. These include drum and disk agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse-running conveyors. The need for agglomeration The main reason for agglomerating heap leachable ores is to prevent percolation problems in a heap. This is different than pelletizing iron ore. In the latter case, the purpose is to bond very finely ground material into coarser, strong particles. These particles can then withstand the rigors of transportation and the loading forces in a blast furnace. Most percolation problems in heaps are caused by the segregation of coarse and fine particles during heap construction. This segregation creates areas with significantly lower permeability because fines plug the channels between coarse particles. Consequently, the leach solutions are subject to channeling, following the path of least resistance. They percolate downward through the coarse ore areas and bypass or barely wet areas that contain large amounts of fines. This results in lower extraction, longer leach time, and higher reagent consumption. Permeability problems in heap leaching are compounded because of the vertical migration of fine particles after the heap has been built. These fines eventually accumulate in pockets or layers and impede uniform solution flow. The fines move because they are not attached to a coarser particle. Moreover, the sluicing action of leach solution flowing over the surface of particles may break the bond between fine and coarse particles. Some fines are also created by the decomposition of ores after being wetted. Percolation problems are minimized if the fines can be attached to the coarser particles. Fines are thus uniformly distributed and rendered immobile within the heap. Heinen (1979) conducted comparative tests of nonagglomerated and agglomerated gold and silver ores. He showed that percolation rates through agglomerated material usually are improved by 10 to 100 times. This reduces leach time for economic recovery to less than one-third of that for nonagglomerated material, and total recovery may be increased. Cyanide consumption is also reduced in most cases because of the shortened leach time. Even run of mine (ROM) ore should be agglomerated. This can be achieved with moderate success by passing each truckload of ore under a water spray to bring total moisture of the ore up to about 8% to 10%. The ROM ore will mix when the ore is dumped, when it cascades down the slope of a heap, or when it is pushed up with a dozer. Overall, agglomeration allows low-cost heap leaching technology be applied to gold and silver ores and tailings that could not be economically processed by conventional methods, according to Phariss (1982). How agglomeration works Agglomeration means that the clays and fine particles contained in the ore adhere to the coarser particles. This creates a coating of fines around the coarse particles. When the ore has few fines and the percolation problems are not severe, the addition of a liquid may be all that is necessary to make the few fines adhere to coarser particles. However, when the quantity of fines is substantial, e.g., +10% -75 µm (-200 mesh), a binding agent may be needed. Use of solution only for agglomeration There are many forces that cause agglomeration and one of them is the surface tension of water. Water-saturated particles collide with each other or with

Jan 12, 1986