Search Documents

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

By John B. Sabey, Vernon R. Degner

The industrial coal processing trend toward greater fines production, due to mining techniques and customer requirements for reduced ash and sulphur content in the fine coal product, is the basis for ongoing efforts to improve the performance of the flotation machine. WCO has successfully adapted the principles of the beds Column to a full size machine prototype. Recent plant evaluation tests confirmed the initial promise of this concept by achieving a considerably lower ash product while maintaining the combustible recovery level of conventional flotation machinery. The paper will include a review of the fundamental principles of the beds Column concept, together with a summary of the WEMCO R&D Program from concept evaluation and laboratory testing, through pilot, to full size machine tests. The performance of the WEMCO/Leeds flotation column will be compared to conventional flotation concepts using a flotation "kinetics" approach, which quantifies the floatable and non-floatable specie recovery performance using the Klimpel model as the basis for analysis. The variety of distinct features unique to this concept include a series of barrier rods which are used to advantage, often together with countercurrent reflux water flow, to achieve a significant improvement in product grade. The hydrodynamics associated with the mechanics of "gangue stripping" from the rising "air bubble-floatable specie" matrix will be briefly reviewed.

Jan 1, 1988

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By Rei Arai, Yuta Yamamoto, Tetsuo Yamazaki, Naoki Nakatani

"Methane hydrate is of interest as an alternative energy resource in Japan and the R&D program has been ongoing for ten years (MH21: http://www.mh21japan.gr.jp/english/). Rare-earth element-rich deep-sea mud (REE Mud) is also of interest as an alternative resource in Japan and an exploration program has been launched in 2013.For methane recovery from the hydrate, a depressurization method pumps up water in a production well and has been successfully applied in field production tests (MH21: http://www.mh21japan.gr.jp/english/). However, micro-bubbles, which appear in the hydrate dissociation and water recovery processes may present an environmental issue. It may stick on clay and silt particles that accompany the recovered water, and may disturb settling of the particles in the water separation tank. For exploitation of REE Mud, an air-lift system has been proposed in the feasibility study (Abe et al., 2012). The same micro-bubble issue is expected during the air, water, and mud particle separation processes. In this research, the authors conducted a preliminary tank experiment for clarifying the effect of micro-bubbles on settling behavior of fine kaolinite particles. The behavior was continuously recorded by a still camera and the images were analyzed by the gray scale intensity. From the results the authors found a suspension effect for the settling of fine particles as the result of micro-bubbles. The effect should be studied in detail for preventing some serious environmental impacts during deep-sea mining."

Sep 1, 2014

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By J. E. Bernick, J. Davies

This paper describes the design and construction of a 22.86 m (75 ft) long jacked tunnel, which was successfully installed, despite difficult mixed face conditions at Metro-North’s Westport Station, in Connecticut in the fall of 2003. The tunnel utilized what is believed to be, the first application of a steel grillage system within the United States. This grillage was installed before the jacking started and allowed the tunnel to be jacked under four live railway tracks, which included the Acela high speed line, without affecting train operations. The clearance between the top of the tunnel and the rails was only 0.9 m (3 ft).

Jan 1, 2005

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003