Search Documents

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

An important problem in mine operations is the classification of material as waste, low-grade stockpile, and ore. This classification must often be made with blasthole data that are widely spaced and that have sampling errors. Geo-statistical simulation techniques combined with basic economic principles allows a procedure for classification that maximizes expected profit. Geostatistical simulation methods (Gaussian, indicator, or annealing-based) allow the integration of hard and soft data in the creation of alternative, equally-probable, realizations of the mineral grade(s). At each location, for each realization, we calculate the "profit" if the block were to be classified as ore or waste The optimal classification is the one that maximizes expected profit (a Maximum Profit Se-lection (MPS) procedure). We discuss the theoretical justification of the method and implementation details. The use of blasthole data from different types of mineral deposits, that is, different levels of continuity, is considered. We also show the efficacy of the procedure with different levels of sampling error. The increased revenue due to the MPS procedure and improved sampling is shown. We show the geostatistical simulation procedure and the uncertainty in block grades that result from incomplete and imperfect sampling. The optimal classification is presented. Optimal block classifications are transferred to realizable dig-limits by hand-drawing polygonal boundaries. We compare the results of the proposed method to classification based on kriging. Limitations and areas of future work are identified.

Jan 1, 1999

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

By Charles A. Gargano

The current state of the mass transit industry in America will be examined. How and why this important urban activity shifted entirely, or almost entirely, from the private sector to the public sector. Who pays for transit? For day to day operating costs? For capital investment? The prospects for transit's future will be the next major issue addressed. In a word, they are rather good. Over the past decade there have been major new transit investments made in Atlanta, Baltimore, Washington, D.C. and Miami, as well as constant re-investment in such cities as New York, Boston, Philadelphia and Chicago. While the current administration has put a temporary halt on the initiation of any major new rail transit projects using Federal funds, there are several mechanisms localities have for using other resources for such projects. These will be explored.

Jan 1, 1983

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar (&apos;total&apos;) extraction coal mine.

Jan 1, 1999

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Our universities and other training institutions are doing just fine meeting the traditional skill needs required by the industry. But are the skill needs going to be the same in the near future? The answer may be NO!! Mining is changing: increased liabilities and costs of environmental and safety issues; lower grades of minerals in traditional mining activities; the advent of new bio-chemical processes and robotic equipment as more productive and economic alternatives; and, larger more sophisticated and automatic equipment. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs, and productivity. And we will be engaging in more undersea mining, possibly space bases processing, less human interaction, and more remote control of events than was ever thought possible in the past. This paper presents several of the systemic changes that are presently and will continue to change the face of mining. It will identify area where education and management will have to address these changes.

Jan 1, 2011

By R. A. Pyper, J. L. Hendrix

Laboratory leaching experiments were conducted to ascertain the effectiveness of acidic solutions of thiourea, CS(NH2)2, for dissolving gold from finely disseminated gold ores. The ore tested was from the Chipmunk ore body of the Northumberland mining district in Nye County, Nevada, USA. Extractions of up to 90% were attained from the ore. Extraction was shown to be dependent on thiourea concentration, ferric sulfate oxidant concentration, acid concentration, and leaching time. Optimum conditions were an ambient temperature leach near pH 1.0 utilizing 100 to 200 kg/ton thiourea and 50 kg/ton ferric sulfate for 8 to 24 hours.

Jan 1, 1981

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009