Search Documents

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991

By Dewey W. Marino

Conventional remote sensing applications for the exploration of natural resources has largely been the domain of low resolu­tion Earth orbiting systems such as Landsat™ which can sample a broad range of the spectrum. As the classic application of remote sensing, it has proven its worth through the discovery of numerous mineral deposits worldwide. Often this technique relies more on the spectral content of the imagery for narrowing potential sites on the ground, but often cannot reveal the detailed context of the observed response. As the dawn of the new era in remote sensing grows closer, high-resolution imagery is proving its worth for the definition of mineral potential and its cost sav­ing advantages for mine management.

Jan 1, 1998

By D. Royston, D. Denlay

Pulp lifters are used to discharge ground pulp from non-overflow grinding mills. In straight-radial channel pulp lifters, discharge is often incomplete and back-flow down the pulp lifter can occur. Leading-curve channel pulp lifters can be used to ensure complete discharge, especially at high mill rotational speeds. The complex motion of solid materials in pulp lifters has been modelled mathematically for both straight-radial and curved pulp lifters in order to make comparisons between the two types. The model is supported by practical observations of the performance of curved pulp-lifters in a commercial 24ftSAG Mill as well as observations of the discharge from several commercial straight-radial pulp-lifter AG/SAG Mills.

Jan 1, 1999

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By William F. Ryan, Paul T. Gribbon

With the rise in construction claims in public works contracting over the years, the use of Dispute Review Boards (DRB’s) in underground construction contracts has become quite common. However, in order for the DRB process to be an effective tool, there must be complete trust and confidence in the Board members and their adopted procedures by both the owner and contractor. This can be difficult in an industry where Board members and contractors may be well known to each other, while an owner maybe involved in a large complex underground project only occasionally. Using case histories, this paper will discuss some recent experiences with the DRB process from an owner’s perspective.

Jan 1, 2003

By Robert C. Peddicord

Application of Quality Management philosophies and techniques commonly referred to as Managing for Continuous Improvement, Team Management , or Managing for Consistency is required in today's mining, manufacturing, and service industries in order to meet quality demands, beat competition, lower costs, optimize operations, effectively use personnel, improve morale, and enhance profitability. Most of these phiosophies and techniques are known to today's managers but either have fallen into disuse or were never allowed to surface in the corporate environment of the organization. Managers should review and adopt the philosophies and techniques of Quality Management and use them to revitalize their organizations and bring about a "paradigm" shift in the way we manage, thereby achieving the goals listed above.

Jan 1, 1991

By John H. Fowler

The 30th Forum on the Geology of Industrial Minerals will be held in the historical seaside city of Halifax, Nova Scotia, from May 22 to May 27, 1994. The Forum will be co-hosted by the Provinces of New Brunswick and Nova Scotia, two of Canada's East Coast Provinces, both having a long tradition of industrial mineral production. Two previous Forums, the 19th in Toronto in 1983 and the 27th in Banff in 1991, offered delegates the opportunity to see industrial minerals in central and western Canada. The 30th Forum will take you to Canada's east coast completing the picture of Canada's industrial minerals from coast to coast.

Jan 1, 1995

By Zhongxue Li, Wenguang Li, Yiqing Zhao, Shuaiqi Wang

"Faced with the serious managerial situations and diverse conditions and needs for mine safety, occupational health and environmental stewardship in Chinese mining communities, an evidence-based approach is proposed for the management of mine safety, health and environment integrity. By the proposed approach, tangible and effective scientific evidence should be collected and accumulated, and the authenticity, accuracy and applicability of the evidence should be assessed to form an evidence-based approach for characterizing mine safety, health and environmental hazards and risks from multidimensional perspectives. The results are then used to formulate diverse safety, health and environment functional requirements. In an evidence-based approach, the evidence is combined with the professional experiences and the actual economic and technological situations, availability and affordability of a mine. This approach is helpful to establish scientific, reasonable, acceptable and effective solutions for identifying and mitigating hazards and improving the level of mine safety, health and environment integrity of mining operations.Introduction / Background In recent years, economic reforms have opened China's economy so that Chinese society has rapidly modernized. Along with this advancement, the exploitation and utilization of mineral resources continues to be active and the scale of mining production continues to increase, which has created a deterioration in resource reserves and as well as the general condition of mining technology. There are many hazards and safety problems in mine production and occupational health as well as in the community environment in China’s mining industry. These problems threaten the security of China's mines and present serious obstacles and challenges to the industry and the government. According to the statistics from the State Administration of Work Safety Supervision, there were 50,500 mine safety incidents in China between 2001 and 2013, which consisted of 31,439 coal mine safety accidents and 19,061 non-coal mine safety accidents, resulting in 30 deaths (Qin 2014). At the same time, mineral dust and radioactive material from mine production processes have increased the morbidity rate of silicosis and cancer in mining workers."

Jan 1, 2017

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By Thomas J. DeMull

Amax Gold's Sleeper Mine was brought to production as an open pit mining, cyanidation milling operation in March 1986. The Sleeper deposit is unique in that it contains zones of very high grade gold ore. Despite blending of ore, mill head grades have varied over a broad range. These grade variations were anticipated during mill design and affected, in particular, the sizing and selection of equipment for the CIP circuit. When grades proved to be even higher than anticipated, design operating parameters were adjusted shortly after start-up to accommodate the higher grades. Operating results have been excellent: during the first 18 months of operations the Sleeper mill has processed 375,600 tons of ore and produced 229,000 ounces of gold.

Jan 1, 1998

By A. Zutshi

Production of CO2 is an inevitable consequence of burning fossil fuels, with the only CO2 sequestration technique feasible in the immediate future being its injection in various geologic media. This paper discusses the factors that influence the injection, movement, and storage of CO2 into deep coal seams, while simultaneously increasing the production of methane. The results of a laboratory-scale study to evaluate the movement of CO2 in coal, its ability to displace methane, and the capacity of coal to retain CO2 are presented. The findings are compared with observations at one of the two field-scale pilot operations practicing CO2 injection in coal. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2006

By E. J. Dorward-King, R. J. Kadeg, S. Pavlou

Risk assessment, risk management, and engineering/economic feasibility analysis are presented as three effective, practical tools for decision making in the remediation of contaminated soils. Risk assessment is applied to evaluate the extent, magnitude and sources of contamination, to identify appropriate contaminants of concern (COCs). Risk management is then applied to identify the acceptable contaminant residual levels for the COCs. Finally, engineering/economic feasibility analysis is used to define the appropriate cost-effective remedial action and associated target contaminant action levels that will achieve the acceptable contaminant residual levels. A real site application of this decision making approach is presented. This site illustrates that through appropriate engineering, acceptable risk-based contaminant residual levels can be achieved with higher action levels.

Jan 1, 1992

By Marcelino Cortina

It is known that underground bituminous coal mining in the Central Asturian Coal Basin (North of Spain) is a complicated task, due basically to the difficult geological conditions: thin and steep Seams with many faults and other disturbances. Therefore, it is not easy to decide what is the most suitable mining method for each of the seams, and problems in making the correct decision are encountered frequently. Because selections in the past have been inadequate an Expert System, ASTURLABOR;hulla, has been designed and will be developed' to provide accurate advice in the mining method selection process. The paper describes the major features of this Expert System and outlines the ASTURLABOR general project, which includes five other mining Expert Systems to complement ASTURLABOR-hulla.

Jan 1, 1989

By Tanya Arsh, Thomas P. Kwiatkowski, Heather Marsh, Barry Doyle

The Big Walnut Sanitary Trunk Sewer Extension Project consists of two segments, the first a 10' excavated diameter tunnel in rock through the gas producing Ohio Shale formation and the second will be microtunneled through unconsolidated water-bearing deposits. Relatively large quantities of methane gas have been encountered in the Ohio Shale. In the softground segment, the sands and gravels contain large water storage capacity and contain shallow residential wells. This paper will present an evaluation of potential gas inflows in the rock tunnel, design considerations for contract documents preparation to inform bidders as to the volumes of gases which may been countered and design options for construction of an impermeable shaft excavation support system to insure residential wells remain in service.

Jan 1, 2001

By Dick Lewis

The Misima deposit is on Misima Island in the Lousaide Archipelago, 240 km east-southeast of the Papua New Guinea mainland, and 600 km east of Port Morseby. Misima is a narrow mountainous island 40 km long and up to 10 km wide. The highest point is 1035 m above sea level. Gold mineralization is restricted to the eastern and less rugged third of the island. The Melanesian population lives in coastal villages. Subsistence agriculture is the main activity, although copra and cocoa are grown in plantations on the eastern and southern coasts. Prior to 1950, mining was important in the economy of the island. Climate is tropical, with little seasonal variation in temperature or rainfall. Tropical cyclones occur about every 10 years (Fig. 1).

Jan 1, 1990

By Bruce Cavender

Production managers look to innovative practices and equipment to reduce operating costs and improve efficiency. These innovations apply to both technical and social aspects of production operations and may be high-tech or low- tech in nature. They may be based on the implementation of a few large-scale "breakthrough projects or numerous small-scale activities, depending on the availability of capital funding and the company's past experience. Successful managers systematically identify innovative opportunities that capitalize on their organization's expertise. They quantify the associated benefits and risks and then manage the implementation of selected innovations to minimize cost and uncertainty. They monitor the results of the innovation after it has been implemented and adjust operating and managerial practices as necessary to maximize the innovation's benefit.

Jan 1, 1998