Search Documents

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By Hans von Michaelis

The revolution in development of new technology and practices in the gold mining and metallurgy industry continues unabated despite the ups and downs in the gold price. Some of the new cutting edge technologies are listed in Table 1 overleaf. There is room to discuss just a few of these here, but many more are identified and described in RANDOL (1992). Cutting edge advancements in gold recuperation, can be sorted into three categories. The first category includes fundamental advances that offer major improvement with significant economic benefits. Second would include evolutionary developments that offer smaller, but nonetheless commercially valuable improvements. Finally there are those "advances" that are interesting but of trivial or question­able economic benefit to industry. It is essential to adopt a "systems approach" philosophy towards developing and applying new technology. Practical innovation often comes about as a result of having to solve a problem. Innovation for innovation sake is an ego trip. Environmental management has become an important part of the system and the environmental implications of new processes and practices in the mine and mill have to be carefully considered for potential benefits and/or liabilities.

Jan 1, 1993

By David J. Gurtler

In early 1988, Chino Mines Co. began using a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction electrowinning plant feed, and non-ore material, to determine its disposition. Results thus far indicate a significant increase in financial returns on material mined compared with the copper cutoff grade previously in use. Chino Mines is a partnership between Phelps Dodge Corp. (two-thirds ownership) and Mitsubishi Corp. (one-third ownership). The company produces copper and byproduct metals from the historic Santa Rita del Cobre mining district in southwestern New Mexico. The history of copper production in the district began with the use of surface native copper by native Americans before 1800. Spanish soldiers from Mexico later became aware of this district and mining began in 1801. The district was worked intermittently until 1909 when the Chino Copper Co. was formed, with Daniel C. Jackling as vice president and managing director. Concentrator operations were started in 1911. Kennecott purchased the company in 1933 and built a smelter in 1939. Chino Mines Co. was formed in 1980 when Mitsubishi purchased one-third of Kennecott's holding at the property.

Jan 1, 1990

By M. E. Hinkle

Concentrations of He, CO2, and O2 in soil gases were measured regularly for more than a year at a site near Golden, Colorado. Samples were collected from a hollow probe at 0.75-m depth and from a plastic hemisphere on the ground surface. Soil temperature, air temperature, percent humidity, And barometric pressure were also measured. Soil moisture was measured only indirectly as amount of rain or snowfall. Higher concentrations of CO2 in both the 0.75-m and surface samples correlated with higher soil and air temperatures, which suggests that CO2 was produced by bacteria. Lower concentrations of helium in both the 0.75-m and surface samples correlated with higher soil and air temperatures. Rain and snowfall appear to affect helium concentrations. Carbon dioxide concentrations were lowest when snow lay on the ground for extended periods of time. No correlation was seen between barometric pressure or percent humidity and concentrations of He, CO2, or O2 at 0.75-m depth or at the ground surface. No correlation, either positive or negative, was seen between concentrations of CO2 and O2.

Jan 1, 1988

By A. D. Davis, C. J. Webb

Brohm Mining Co.'s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February 1999 the Governor of South Dakota announced plans to request the US Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable groundwater reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2003

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By B. D. Hansen

Newmont has been on a focused path of improving operations for many years. After the merger of Newmont and Santa Fe Pacific Gold, Newmont created significant synergies of over $50 million per year in Nevada, primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. This paper will describe the methods and programs that continue to be implemented at Newmont's many mine facilities in Nevada. Newmont has used a combination of computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and a variety of available metallurgical processing options to decrease the cost of operations and increase profitability.

Jan 1, 1999

By B. D. Hansen

Newmont has been on a focused path of improving operations for many years. After the merger of Newmont and Santa Fe Pacific Gold, Newmont created significant synergies of over $50million per year in Nevada, primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. This paper will describe the methods and programs that continue to be implemented at Newmont's many mine facilities in Nevada. Newmont has used a combination of computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and a variety of available metallurgical processing options to decrease the cost of operations and increase profitability.

Jan 1, 1999

By J. D. Shenk

The White Cliffs diatomite deposit occurs in a lacustrine facies of the Quiburis Formation, an Upper Miocene to Pliocene basin-fill sediment of the lower San Pedro Valley. On-going geo-logic mapping has defined an 2.5-3.0 m (8-10 ft) thick ore zone near the mill site, several marker beds, a NNW-trending high-angle normal fault, and a NW-trending syncline. The diatomite has an average loose-weight dry bulk density of 130 kg/m3 (8 lbs/ft3) and is presently marketed outside Arizona for asphalt filler. Current development is projected to yield 3500 mt (4000 st) of finished product, with an estimated 91,000 mt (100,000 st) of finished product obtain-able from several other nearby sites.

Jan 1, 1988

By K. A. Sauer

Blasting can create severe interference for a mine's carbon monoxide based fire detection system. At the present time, without being able to differentiate between blast and non-blast carbon monoxide, a fire detection system must either set fairly high alarm levels for its sensors, or allow frequent "false" alarms to sound during blasting. This paper will introduce current work being done which will attempt to define characteristics of the carbon monoxide concentrations time curve for blasting. The work uses drift blasting for its data base as it is one of the more common forms of blasting. Future work with the data may produce a mathematical model which can be used to monitor and identify the carbon monoxide time curve for drift blasting.

Jan 1, 1989

By D. S. Bloswick

An investigation an4 analysis of slip/fall accidents specifically pertaining to underground coal mines was conducted. From a population of 751 accident reports, three major sources of injury which account for over 80% of the incidents have been identified. The specifics of this study are presented in this paper. Based on the results, several recommendations are made to reduce such accidents in underground mines. In addition, a brief discussion of the slip-hazard analysis laboratory at the University of Utah, which will be useful in future analyses of these accidents is presented. Work in this facility includes the simulation of certain mining activities in a controlled setting. Foot forces are measured and work methods subsequently developed to minimize the slip potential of these activities.

Jan 1, 1988

By M. Z. Dogan, M. S. Celik, G. Onal, O. Ozcan, I. Yildirim

A fluorite ore (51.85 % CaF2) containing high contents of calcite, quartz and iron oxides was upgraded by flotation using a new reagent, oleoyl sarcosine (OS). In addition, quebracho and sodium silicate were used as depressants for calcite and quartz, respectively. The effect of pH, collector and depressants concentrations on grade and recovery was determined with the aim of optimizing the flotation conditions. Application of the two-stage cleaning achieved a concentrate assaying 92.17 % CaF2 with 80.1 % recovery. The Si02 content (0.76 %) was below the required level of 1 % SiO2. The mechanism of interaction between OS and fluorite, as compared to oleic acid, is also elucidated based on the zeta potential measurements.

Jan 1, 1993

By Robert A. Hains, William P. Balaz, K. Payne

Ceramics are usually used to line chutes, pipes, dust collectors, separators, cyclones or bins where abrasive or corrosive material is moving. Improvements in ceramic manufacturing methods and quality, use of other abrasion resistant materials in combination with Alumina ceramic, improved adhesives and installation methods allow the use of Alumina ceramic tile in applications with impact. This paper discusses the criteria to determine if ceramics can provide a cost effective alternative to other liners for abrasive material handling applications, design parameters for liner systems, system costs, and case histories. The goal will be to provide a practical guide for improving the performance of existing ceramic lined systems or determining if ceramics is a cost effective solution for your abrasive material handling applications.

Jan 1, 1996

By G. S. P. Pereira, E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality overtime. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By Jennifer B. Leinart, Otto L. Schumacher

JIM ARNOLD: Our next speaker is Otto Schumacher. He's president of Western Mining Engineering in Spokane, Washington. His company offers services in the area of mining feasibility analysis and publishes Mining Cost Service. Otto's talk will be "Are Metallurgists Overpaid?" [laughter] I know one that's not. [laughter] OTTO SCHUMACHER: I really think it's kind of a dirty trick for Doug to put me up here and pose that question since I'm a mining engineer. However, it's probably most appropriate that a mining engineer address the question because I can be more objective than the rest of you. [laughter] SPEAKER. Otto, do you promise to say something nice about metallurgists? [laughter] OTTO SCHUMACHER: I'll see how much time I have. [laughter]

Jan 1, 1998

By Risto Lindsberg

A wide concept of flotation equipment and technologies is presented in this paper. The basis for the presentation in Outokumpu's world-wide experience in mineral processing and other related areas, and continuing research and development work done in Finland as well as abroad by Outokumpu's subsidiaries (and customers). It is understood that flotation equipment selection for a certain process stage is becoming more complicated. It is obvious that flotation equipment in grinding circuit needs different design from a multistage cleaning process. In this paper, column flotation is compared with other flotation methods. Thus three areas of flotation are discussed in this paper: 1. Flotation in the grinding circuit, Skim-Air machines 2. Rougher-scavenger flotation, conventional cells vs columns 3. Cleaning flotation, columns

Jan 1, 1988

By Robert Stauffer, John Frostiak, Rein Raudsepp

Placer Dome's Campbell Red Lake Mine in Balmertown, Ontario produces a refractory gold flotation concentrate containing the sulphide minerals arsenopyrite, pyrite and pyrrhotite. In 1991, the existing concentrate roasters will be replaced with a pressure oxidation plant based on Sherritt Gordon technology to update the facilities and to satisfy environmental requirements. A successful continuous pressure oxidation miniplant program was conducted by Sherrill Gordon in late 1989 which formed the basis for the design of the commercial plant. The paper summarizes the Campbell operation and the environmental aspects of the project, and discusses the results of the miniplant program and the design of the commercial plant. The capital cost of the pressure oxidation plant and the process operating costs are also presented.

Jan 1, 1990

By C. A. Fleming, C. J. Ferron, P. T. O'Kane, D. B. Dreisinger

The platinum group metals (PGM's) are typically recovered by flotation, smelting of the flotation concentrate to matte, and matte leaching. Concentrates too low grade to be processed economically by the conventional process require a new treatment route. PLATSOL, a new pressure leach process, was developed for the Northmet deposit and dissolves in one step base and precious metals (PGM's and gold). Various options exist to recover all pay metals from the leach liquor. The preferred option to date involves a solid-liquid separation, followed by sulphide precipitation of gold and the PGM's, and copper solvent extraction using commercial solvent extractants. This paper briefly summarises the process and the effect of the main leach parameters. Application of the PLATSOL process to various feedstocks is also presented.

Jan 1, 2000

By J. H. Lammers, John Turney

The Eskay Creek Project was interesting in many respects, includ­ing extremely high grade of precious metals, refractory nature of the ore, carbonaceous content of ore resulting in preg robbing, and high content of many heavy metal sulfides in addition to the usual iron sulfides. Although the process plant was never constructed, extensive testwork was conducted and a flowsheet for the treat­ment of the effluent form pressure oxidation was developed as a basic engineering package. The flowsheet included removal of iron and gypsum by neutralization, selective recovery of copper by zinc precipitation, and recovery of zinc by solvent extraction and electrowinning. The zinc recovery produced a significant impact on the project economics. The waste water from the process met the environmental requirements for British Columbia.

Jan 1, 1996