Search Documents

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Y. J. Wang

Editor's Note: Y.J. Wang's paper appeared in the September Technical Papers section. There were some inadvertent editorial errors in it. So we are reprinting it here. Abstract - This paper examines the ventilation network problem from a view point of solving a system of B equations in B unknowns, where B is the number o f branches in the network. Based on Kirchhoff s current and voltage laws, the solution to the general ventilation network problem must satisfy B network equations. In this paper, the air quantities and control-device pressures are chosen as variables and are grouped into B dependent variables (unknowns) and B independent variables, resulting in a system of B equations in B unknowns. Based on whether their variables are dependent or independent, the network branches are classified into f our types: five d, non-fixed, p-fixed, and q fixed. The ventilation network problem may include all four types of branches. There are .some conditions under which the problem as defined in this manner does not have a unique solution. To have a unique solution, the Jocabian matrix of the equations m us! he nonsingular. It then follows that: • the number of branches with independent air quantities must be less than or equal to the number of chords with respect to a spanning tree; •the subnetwork of branches with independent air quantities must not contain any cutset; and •the suhnetwork of branches with dependent control-device pressures must not contain any cutset. These three conditions must be met regardless of the values for the variables. In addition to the problem formulation, a solution procedure applying the Newton (or Newton-Raphson) method is outlined and illustrated with an example problem.

Jan 1, 1991

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Craig Cina

Transporting goods from producers to consumers is a fundamental part of the US economy. The demand for transportation closely reflects the economic health and well-being of the nation's industrial, commercial, and agricultural sectors. The inland waterway barge industry has traditionally played a key role in transporting needed commodities to industries on an economical basis. Barges account for 10% of the domestic intercity tonnage carried by all transportation modes. Water carriers operating on inland waterways hauled more than 450 Mt (500 million st) of cargo in 1980-up from 428 Mt (472 million st) in 1970. Inland Waterway Shipments Metallic and nonmetallic minerals comprise one of the largest commodity groups moved on inland waterways. As illustrated in Table 1, metallic and nonmetallic mineral shipments accounted for more than 69 Mt (77 million st), or nearly 15% of all commodities shipped in 1980. Putting this tonnage in perspective, coal and petroleum represent the two largest commodities moved on inland waterways. In 1980, petroleum and petroleum products accounted for 138 Mt (152 million st), or 28% of all commodities shipped. Similarly, coal represented 120 Mt (132 million st), or 25% or all commodities shipped. Even though shipments of metallic and nonmetallic minerals are smaller than coal and petroleum, they still account for a sizeable portion transported. The inland barge industry moves a variety of metallic and nonmetallic minerals ranging from manganese ores to building cement. Minerals transported by barge include: • iron, copper, bauxite, and manganese ores for metal production; • lime and limestone for construction and electric utility scrubbers; • phosphate rock, natural fertilizers, and gypsum for agricultural needs; • sand, gravel and crushed rock, clay, asphalt, tar, and pitches, and building cement for construction purposes; and • a host of other minerals to meet industrial needs. A few mineral commodities are responsible for a large proportion of waterborne mineral shipments.

Jan 10, 1982

By Oleg N. Tikhonov

A new extraction method which includes a combination of gravity and alternating electromagnetic fields with interfriction of mineral particles was proposed (Tikhonov O.N., 1979) and tested in lab conditions at Mineral Processing Department of St. Petersburg Mining Institute. At the beginning of the work the main goal was to find an efficient alternative to traditional extraction methods (like shaking table, etc.) used for concentration of fine alluvial gold particles. After the method and a series of gradually improved lab separators (Tikhonov, et al., 1983) were positively tested for gold (Tikhonov, et al.. 1986) the efficiency of the method was also proved for extraction of and other heavy minerals from alluvial and ground ores in experimental work at the St. Petersburg Mining Institute. The fine heavy minerals were separated to concentrates with high technological indices (Andreev et al., 1987), (Tikhonov, Gladkov, 1987), (Tikhonov, Gladkov 1989). In parallel a semi-industrial gravi-electro- magnetic separator was made and several technological flowsheets were designed for testing the method in industrial conditions (Tikhonov O.N., Miazin B.N., 1987), (Tikhonov O.N., Tolstunov S.A., Jebelev V.V.,1989). A series of industrial tests accompanied with complete sampling and standard technological measurements were performed at several alluvial deposits, with good technological indices. Thus the method and the flowsheets displayed high additional recovery of fine alluvial gold particles during elkrated industrial experiments in Siberia (Aldan province). At higher concentrate grade this method, even in one-stage operation, increased gold recovery more than by 25% compared with shaking table (for particles -0.10 mm gold recovery was 82% vs. 55% by shaking table, for particles - 0.25mm the recovery was 97.5% vs. 61.8%). Experiments were performed by joint team of St. Petersburg Mining Institute and the Irkutsk Institute of Rare Metals (Tikhonov O.N., Gladkov S.A., Tarasova T.B., 1991).

Jan 1, 1995

By John W. Kelse

What happens when the skull and crossbones goes on a product? In the case of cancer warnings, the consequences can be severe. If the label contains the term "lung carcinogen", you might expect to compensate a lot of smokers, meet a lot of expensive lawyers, be counseled by equally expensive consultants and pay sharply elevated insurance premiums, if you are able to obtain coverage at all. At the extreme, you may face plant shutdowns, job losses or even Chapter 11 bankruptcy. Regardless of how you fare, you are likely to learn some very disconcerting things about the risk evaluation and regulatory system which required you to label in the first place. If a particular material or product does pose a health risk, you are obliged both legally and morally to warn those potentially exposed. Once that warning appears on the label, however, the consequences are often beyond your control. You and your embattled product become part of a legal/regulatory system which has a life of its own. Therefore, the issue of health labeling is not so much whether one warns but rather whether the warning itself is justified and the reasonableness of what happens afterwards. It is this matter of justification and reasonableness, particularly of cancer warnings, which this paper addresses. Until, as they say, your ox has been gored, we tend to believe that risk is determined by the best available technology and expertise We expect that risk evaluators appreciate the ramifications of their work and place things in proper perspective; that risk has been appropriately demonstrated before it is publicized and regulated; that the time-honored concept of prudence, to err on the side of safety, has not been excessively stretched. Unfortunately, the risk evaluation process is rarely, if ever, this

Jan 1, 1991

By Joseph M. Denk, John N. Baran, William J. Francart

Filling or sealing shafts of underground coal mines is required when the mine is declared inactive by the operator, permanently closed or abandoned for a period of time greater than 90 days. Although shaft filling requires the use of incombustible materials for the first fifty feet of the shaft, a sparking potential may exist which has been reported to be the cause in at least one shaft-filling explosion. This paper outlines the method used at the explosion site to monitor mine gases within the shaft to assure the safety of the workers involved in the remainder of the shaft-filling operations. Gases which were monitored include methane, oxygen, carbon monoxide and carbon dioxide. Continuous sampling was conducted twenty-four hours per day to determine the methane liberation and accumulation of gases within the shaft. Once gas concentrations were evaluated, the need for ventilation in the shaft was obvious because methane accumulations within the shaft were in the explosive range. Several methods to ventilate the shaft were explored. The most practical seemed to be the dilution of gas concentrations with compressed air to inject a quantity of fresh air into the shaft. But, when the compressed air was stopped, a buildup of an explosive mixture reoccurred. The pattern of gas accumulation was then studied to find the correct combination of ventilation and shaft-filling time periods which would a1 low for the greatest reduction of the potential for an explosion. Gas concentration sampling continued during the remainder of shaft-filling operations at this shaft and four others at the same mine. In conclusion, this paper illustrates some of the problems which are often overlooked in a shaft-filling operation. If addressed, the work can be done in a safe and feasible manner.

Jan 1, 1987

By O. Guyot, T. Mulpeter

Sadiola Hill mine is located in the sub-Saharan part of Mali. In its first two years of operations, Sadiola Hill mine had already exceeded expectations with respect to profitability, plant capacity, metallurgical recovery, cash costs and social integration into the area. The advanced control system installed by the authors has been a major contributor in the substantial throughput of the mill over the design tonnage with no loss of recovery. The run-of-mine ore at Sadiola consists of soft clays with a varying percentage of grit, producing a high viscosity slurry. The percentage of grit fed to the plant varies on an hourly basis. This combination was expected to have a large impact on the milling circuit and determined that the early installation of an expert mill control system would be advantageous. Svedala Cisa OCS©, was selected as the most suitable support software. The operational rules and control philosophy are housed in the OCS© graphic-oriented fuzzy expert system while a model­based Soft Sensor has the remarkable ability to detect the variations in grit in the feed. Designed during the second half of 1996, commissioning of the system began in March 1997, the OCS was fully on-line by September. With the implementation of the optimising control strategy a throughput of 5.0 million tons relative to the target of 4.4 million tons was achieved for the 1998-operating year. The Sadiola project confirms that advanced process control techniques are among the most cost-and time-effective methods of improving metallurgical plant performance. The recipe that worked at Sadiola is a mix of metallurgical expertise, proper software selection, adequate design of control philosophy, and excellent plant support and follow­up. The early decision, design and installation of the mill control system has resulted in an enhanced Return on Investment.

Jan 1, 2000

By Steven A. Elmquist

INTRODUCTION R&D activities are needed, at a minimum, for a company's competitive survival followed in importance by the growth and diversification of the company. For most industrial companies, however, R&D is the business area that has been the most difficult relative to confident long-range financial commitments and effective control and relative to its value as a long-term investment. Investors look not only at the current profitability of the company but increasingly at the plans, actions, and quality of the personnel in position to improve the market position and profitability of an organization. "The strongest predictor of investment value is the degree of innovation of the 'company.' I believe this is true of both strategic planning and R&D activities." R&D is the lifeblood of a company's future. If this basic premise-R&D for survival and growth-is believed to be true, why is it necessary to "Sell R&D in your organization? My personal experience, in a number of organizations, is that R&D budget is perceived as a business element area that could be delayed or reduced to improve the bottom line during difficult business conditions. I believe the following quote speaks volumes about this subject-"There is only one thing I know for certain about research, and that is it costs money-lots of it." -Unnamed, Hard- headed Financial Executive. A business must make money and be profitable in order to maintain and create jobs, pay taxes, cover working capital and costs of goods sold, and most importantly, create value for its shareholders. The foremost element of selling R&D, therefore, is to consistently demonstrate the R&D group's contribution to the bottom line.

Jan 1, 2004

By Dr. H. Askew

The input needs of the steady state modelling process are outlined and a methodology for designing a plant survey to meet those needs described.

Jan 1, 1995

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By Robert L. Bates

The field of industrial minerals and rocks includes such a wide diversity of materials and occurrences that communication is essential to foster a sense of "belonging? among geologists and other professionals. Besides, exchange of ideas and information is essential in meeting the needs of an ever-expanding world economy. A survey of the field shows to what an extent such communication--especially in the form of conferences and their proceedings--has increased during the past 25 years.

Jan 1, 1995

By D. Erik Spiller

A commercialized dry gravity concentrator is operating on an alluvial gold deposit in the Boludo Mining District, State of Sonora, Mexico. The technology base of the process is the Rotary Air Concentrator (a dry circular air jig) that recovers gold from the desert sand resource. An overview of the Mexican operation and the dry concentration technology is presented. Application of the dry technology to pretreat­ment of heap leach feeds and other heavy minerals is a pos­sibility.

Jan 1, 2000

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By Des B. Bolton, Neil P. Boland

Typically, environmental work on mine sites in Northern Australia involves addressing an individual problem as it arises. However, individual mining companies are moving toward a more holistic approach to managing the interactions between the environment and the mining process and are thus pre-empting environmental problems. This paper presents a broad overview of this holistic approach and provides a few examples, drawn from our own experience, which illustrate some of the tangible benefits to be gained from Environmental Planning.

Jan 1, 1991

By E. A. Devuyst, G. H. Robbins

The Inco process can be retrofitted into a typical heap operation with minimum capital. Capital cost for a mid to large size heap would be less than 1 cent/ton. Operating costs are typically in the order of 8 cents/ton. Ammonium bisulphite is the preferred reagent. The process provides the equivalent of fresh water r?1s­ing and thus minimizes the time of the _nnse program. A typical heap (the Snow Caps Mine, California) was rinsed completely

Jan 1, 1996

By Ken Criley, Marc E. Orman

Identifying the optimum ultimate height for heap leaching ore requires the consideration of a number of competing factors. A primary limitation is the reduction in the permeability of the ore with increasing heap heights. At low permeabilities the heap can blind off, cause serious ponding and runoff, and become very difficult to rinse at closure. The authors present a laboratory methodology that has been successfully used on several projects to identify the maximum height for controlling heap permeability.

Jan 1, 1996

By R. R. Smith

The meaning of the title, "Blank Piece of Paper," refers to the need for management to take a completely fresh viewpoint to the problems facing our industry. These problems are so severe and some so new that conventional thinking may not be adequate to resolve them. Innovation has to be a part of every company's approach to the solutions, our concept is to start with a "Blank Piece of Paper.' The objective of 'this paper is to outline steps which can be taken to improve the profitability of a mining business. This is not an examination of technical solutions to individual problems, but rather recommendations for overall change in management thinking. This philosophy is based on our actual, hands-on experience in major open pit operations worldwide over the past 25 years.

Jan 1, 1987

By A. Kalmes, B. Dehler, D. Kopp

Nutrien has six potash mines in Saskatchewan and has been proactive in maintaining the integrity of their tailings facilities through ongoing assessment, design, operation, inspection, and monitoring. Nutrien commissioned a system inventory and semi-quantitative risk analysis (SQRA) of all dikes to further environmental stewardship at their potash facilities. The inventory assessed nearly 100 dikes; each dike was rated according to a probability and consequence factor and assigned a risk score. The risk scores were used to develop a risk matrix for each of the six sites and risk-response actions for each dike and segment. The inventories and SQRAs will help each site assess priorities for investigation and risk mitigation, if necessary. The study results will also help Nutrien refine corporate wide tailings governance standards and demonstrate compliance with various governance regulatory obligations.

Mar 2, 2022

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012