Search Documents

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, A. E. Clark, R. P. Bush, L. E. Schultze

The U.S. Bureau of Mines conducted copper exchange capacity (CuEC) tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the CuEC as a function of Cu concentration, pH, and temperature. Further testing resulted in regression equations expressing CuEC's of Na and Ca montmorillonites and attapulgite as a function of Cu concentration, pH, and the concentration of metal ions which compete with Cu for exchange sites. Using these equations, an analysis was made of the impact each clay could have on overall copper recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of copper from in situ leaching solutions. Copper losses are decreased by the presence of competing ions, and A1 and Mg have the largest impact of those ions normally present in Cu leaching solutions.

Jan 1, 1993

By Ben L. Seegmiller

The basic compression-yield concept of roof support for mine roadways requires that the mine roof be placed in a state of compressive stress. The compressive stress may be achieved using a support system such as an entry truss or other specialty truss device. Furthermore, the roof must be allowed to yield, but with great resistance when abutment loads are placed on the roadway. The resisted yielding may be provided using a new yieldable steel prop, known by the trade name, YIPP~. The yieldable steel prop can allow as much as 1.5 m[5 ft] of yield, or up to approximately 40% of the opening height, while providing a resistance in excess of 60 mt[66st]. More than fifteen mining operations including coal, trona and hard rock mines have field tested the YIPPI . Present results indicate that the yieldable prop provides a cost-effective alternative to wood cribs, concrete cribs, hydraulic props and other steel prop supports. The paper describes the YIPPI including its unique principle of operation, its applications and actual field performance.

Jan 1, 1992

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

By Dave Watson

Henderson Mine personnel have more than 20 years experience and have placed more than 400,000 m3 (520,000 cu yd) of shotcrete and concrete. Over the last 20 years, the mine has used a variety of equipment to place concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Recently, the mine received a state-of-the-art wet shotcrete placer. The batch plant was automated, and a mobile concrete-form jumbo was fabricated. The mine will also receive a new concrete transport truck. Henderson’s background The Henderson Mine is owned by Climax Molybdenum Co., a unit of Amax, Inc. It is an underground, primary molybdenum producer near Empire, CO. The mill is located between Silverthome and Kremmling, CO and is connected to the mine by 16 km (10 miles) of underground and 8 km (5 miles) of surface track. Except for the ore haulage system which is powered by overhead trolley, all mobile equipment is rubber-tired and diesel-powered.

Jan 1, 1992

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992

By John T. Crawford

Open pit limit analysis techniques of various types have been utilized for many years to design ultimate pit surfaces. In the last 15 years there have been many advances in the development of sophisticated computer methods to aid this process. The extensive capability of the computer has led to multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long-range and intermediate-range mine planning and design questions. A single computer run develops a pit design from a set of data. A set of nonsequential runs is used to evaluate changes in pit slopes, property restraints, and mineral model variables. Ore reserve economic sensitivity and intermediate-range mining plans can be developed using sequential computer runs. Present value methods are incorporated by using iterative sequential techniques. Multiple ore processes, dump leaching credits, and the trade-off between open pit and underground mining can also be handled. Many of the applications described are representative of current practice. The remainder are suggested extensions.

Jan 1, 1979

By Gary Johnson, Bill Mackenzie

The Paddy's Flat plant of Dominion Mining Limited was commissioned in March 1988 with a design throughput rate of 700,000 tpa. The plant now treats ore at an annualised rate of over 2,000,000 tpa. The only major capital improvement to the plant has been the addition of a pebble crushing circuit. Whilst significant changes in the average hardness of the ore being fed to the plant have obviously occurred, a number of processing innovations have been necessary to enable these throughputs to be maintained. The treatment of ore types with a wide variety of physical properties has been a feature of the operation of the Paddy's Flat plant. The leaching characteristics of the ores are relatively straight forward, and it has been possible to considerably enhance the rate of gold extraction from the ore. Reserves of soft surface ore have been increased which has created the opportunity to improve the profitability of the operation by increasing throughput to considerably above the design level, without having to increase the capital investment in the plant.

Jan 1, 1992

By Malcolm Wills

Boddington Gold Mine commenced operation in 1987 with an initial production of 3.0 Mt/y at a grade of 3.5 git. Head grade has reduced over the life of the mine and the major response to the drop in grade has been to increase mining rates and increase plant throughput. A capital expansion was carried out in 1996 increasing the throughput to 6.0 Mt/y and since that date tonnage has been increased without major capital expenditure. BGM's current mill throughput is 8.77 Mt/y ( 1999). In 1999 the combined basement plant and direct leach plant processed 8,770,055 tonnes to produce 233,507 ozs or 7.262882 tonnes of gold at an average head grade of 0.83 git. With grades of 0.83 git, and gold price at record lows, $US251.95loz in August 1999 or $A393.67loz it has been necessary to make and maintain major cost savings to remain profitable. Boddington Gold Mine has achieved this by a number of steps including a productivity study by outside consultants.

Jan 1, 2000

By David Lunt, Evan Kirby, Peter Mason, Ian Ritchie

The treatment of refractory gold ores, in particular the "competing" technologies and their relative advantages and economics, has become a major segment of most mineral technology oriented conferences in recent years. A common theme is the increasing refractory nature of gold ores being treated. This is despite ores such as those at Kalgoorlie having required roasting for liberation since the last century. Papers on refractory gold treatment have examined the characteristics of refractory ores and the causes of reduced recovery (eg La Brooy 1994), the available technologies and their relative economics eg Litz 1990), and the selection of a suitable process route (eg Nicholson 1993, Weston 1994). The most comprehensive collation of data on such processes is provided in the different editions of Randol. A variety of classifications and definitions of "refractory ore" have been published. Due to the many factors which can impact on the recovery of gold it is perhaps not feasible to develop a universal characterisation that can be applied to all gold bearing rocks. La Brooy et al have provided the framework for characterisation shown in figure 1.

Jan 1, 1995

By Vitaly T. Borisovich

Mining economics courses have been taught in Europe for more than two centuries and in the United States for most of this century. They are the mineral industry's version of engineering economics offered by industrial engineering departments. In the 1930s, mineral economics first appeared in American mining schools. This subject goes beyond the deposit and the mine. It examines the economic aspects of mineral resources in general and the individual mineral industries in particular. In 1947, the first degrees in mineral economics were granted in the United States. There are mining and geological engineers who specialize in mining economics. But it has rarely become a separate degree program. Rather, in this country and several others, a graduate student in a mining department or school will include economics in his course work. Then the person writes a thesis or dissertation on a mining economics topic. One exception is found in Moscow at the Department of Geoeconomics of the Moscow Geological and Prospecting Institute (MGPI). To place this program in perspective, some background is needed on education in the Soviet Union.

Jan 1, 1991

By Thomas E. McNider

On July 20, 1990, a Spontaneous Combustion Control Plan was approved by MSHA for Jim Walter Resources, Inc. No. 5 Mine. The mine operated under the plan for twenty-nine shifts before MSHA revoked the plan. A total of fifty-five seals were constructed during the process of implementing the plan. The major difficulty in applying the control concept resulted from problems controlling leakage at the numerous seals. The number of seals was a direct consequence of attempting to merge the traditional bleeder system, used in all the Blue Creek Mines, with the bleederless system Jim Walter Resources proposed as a means of controlling the spontaneous combustion hazard. This paper discusses Jim Walter Resources experience with spontaneous combustion control and the new safety standard which applies to underground coal mines that demonstrate a history of spontaneous combustion and how this standard would apply to our No. 5 Mine. The new Ventilation Standards were published in the Federal Register on May 15, 1992, and scheduled to go into effect August 16, 1992.

Jan 1, 1993

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By Wiston Rocher

The Minera Ojos Del Salado (MINOSAL) concentrator is located 20 km (12 miles) southeast of Copiapo, Chile. It processes copper ore provided by its Santos and Resguardo mines at a capacity of 4.2 kt/d (4620 stpd). In 1982, Phelps Dodge acquired the majority interest in MINOSAL to explore the property's potential. At that time, the concentrator plant was a small, antiquated installation with a capacity of 674 t/d (740 stpd). At the time of the pur¬chase, the majority of the ore was produced from the Santos and Resguardo mines, but custom ores of copper, silver and gold were also treated. The acquisition occurred at a crucial time in the copper business, since the price had fallen to nearly 50 cents/ lb. In 1985, Phelps Dodge purchased the outstanding interest in MINOSAL and acquired 100% of the property. Today, after numerous improvements and two expansions, the concentrator is a combination of old and new equipment. The regrind mills, for example, have been in service for about 50 years, while the ceramic concentrate filter represents the latest technology.

Jan 1, 1993

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By A. H. Balch

A physical elastic seismic model, based on the Peoria oil field was constructed and used to produce multi mode cross-borehole seismic data. Because this was a physical model, it was necessary to deal with a complex wave field consisting of compressional waves, shear waves, and converted waves. The recorded raw data were complex, have no resemblance to the inter-well geology, and were difficult or impossible to interpret. These unintelligible data sets were extensively computer processed. Detailed, accurate, images of the inter-well structure, and reflecting horizons were obtained as a result of this processing. This investigation demonstrates that excellent, accurate images of the inter-well geology can be obtained by skilled seismic cross-well data acquisition and extensive careful computer processing.

Jan 1, 1993

By Martha S. J. Leary, Malcolm J. McPhersqn

This paper introduces a computer simulation which extends the utilization of microcomputer systems for mine ventilation planning. The program was developed as part of an ongoing study to produce a simulation model that would determine the optimum duties of a main fan and a booster fan without requiring the trial and error runs that are necessary with currently available programs. To use the new program, the user specifies the location of one main fan and one booster fan, and the minimum required airflows in any number of working places. The computer deter-mines the fan duties that will maintain the required airflows at the lowest operating costs without causing undesired recirculation. The methodology of the program and an example showing how it can be applied are presented.

Jan 1, 1988

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By R. V. Ramani, R. Natarajan, A. Bhattacherjee

Industries in general, and mining in particular, have become safer than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction, as required, through job redesign, work procedures and worker training. Mine accident and hazard control must be practiced in a manner consistent with the overall objectives of the mine management, which include the optimum allocation and effective utilization of the resources. The purposes of this paper are to: • present a set of analytical tools to analyze injury experience data. • apply these tools on a case study example, • discuss the results of the case study, and • identify the application limitations and the future research needs.

Jan 1, 1993

By W. T. Gorton

Bonds are required by state and federal law to address reclamation when the permittee defaults. Under various principles of law, a bonding company may propose to perform the obligations of the permittee, however, the negotiations with the regulatory agencies, surface and mineral owners and other interested parties can create a very complicated scenario that requires an understanding of the law regarding environmental protection, bankruptcy and surety ship, along with technical expertise in land reclamation. This paper presents the engineering professional with a framework regarding areas of law that pertain to surety reclamation projects and negotiations with state and federal agencies and related parties. Though presented in the context of the coal industry, the principles discussed are generally applicable to the mining industry as a whole.

Jan 1, 2003