Search Documents

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By Axel Nitschke, Josef Arnold

Bochum’s Underground Lot 306 was characterised by a confined site and unique tunnelling methods. A highly mechanized construction concept was developed to achieve high progress rates. Bespoke backup systems for muck disposal and material supply were used. For the first time in suburban tunnelling, wet shotcrete, batched onsite, was applied. A three-storey underground car park had to be undermined with only1.5 m of overburden and had to be lifted several times by “compensation grout in.” An existing operational two-lane metro tunnel was enlarged without any major impact on train operation.

Jan 1, 2005

By Stuart F. McTavish

Mechanically suitable grinding mills became available to the mining industry in 1908. Since then, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. Most important, they had to last long enough in an operating mill to protect its structure from the abrasive wear of the ore and the grinding media. In addition, they had to be capable of efficiently transferring the energy from the mill to the mill charge in order to facilitate the grinding process. And these liners had to be easy to install and remove. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high-carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. In the early 1920s, pieces of solid rubber truck tires were used as emergency repairs for broken cast metal liners. Thus was rubber first introduced as a mill liner material. The first patent for rubber mill liners was awarded in 1921 to James Denny and Rolla Watson, both of the Coniagas Mine in Cobalt, Ontario, and to Dale Barnum of the Comstock Lode in Virginia City, NV. This original design was covered under US Patent No. 1470597. It had a fabric backed rubber that was bonded to the shell of the mill.

Jan 1, 1990

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By Chris Tattersall, Tomyuki Kudo, Peter Raleigh, Nestor Garavelli, Steve Redmond, Michael J. Lehnen

Twin bore running tunnels driven approximately 4,500 route feet by a Mitsubishi Heavy Industries (MHI) EPB Tunnel Boring Machine link the West Portal and East Portal on this complex Light Rail Project. One third along the way, the TBM arrives at the Beacon Hill Station which is the deepest underground “binocular” station of its kind in North America and then “walks-across” the station to be re-launched on the other side to complete the drive. This paper discusses briefly the layout and design considerations but then focuses more deeply on the approach by the Contractor to drive and supply the tunnel. The paper addresses the approach used to launch, re-launch and recover the TBM and touches briefly on muck volume control and monitoring plus settlement monitoring and the performance achieved. Also of interest is a unique solution to a difficult launch situation involving a secant pile tieback wall designed with several rows of double I-beam steel walers spanning the eye at the West Portal under the I-5 freeway.

Jan 1, 2007

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

By G. M. Bernard

The Andacollo gold mine is located near the small town of Andacollo, Chile (population 14,000) in the fourth region. It is approximately 35 miles by paved road from the coastal city of La Serena, and Santiago lies about 300 miles to the south (see map.) Site elevation varies between 3300 feet and 4200 feet. The climate at the site is moderate but arid, with an average annual rainfall of only five inches. Because there is little rain, and the temperature varies only a few degrees (57"F to 75°F); there are no freezing, solution dilution, or pad saturation problems. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By C. J. Bise, M. F. Sindelar

Regulations, such as the MINER Act of 2006, require the installation of redundant and secondary communication systems to assure that contact can be established with coal miners who may become trapped underground as a result of an event such as a fire, explosion or inundation. For half a century, the orientation towards underground communications has been that more complex systems better serve the coal miner. However, if a goal is to provide for an alternative means of establishing communication between the surface and trapped miners underground, then some of the technology employed should be simple, reliable and cost-effective. Coal mines spend hundreds of thousands of dollars on exploratory drillholes to characterize reserves, sometimes decades ahead of mine development. During the pre-mine planning phases, certain exploratory drillholes could be located and then outfitted with a simple communication link that would remain compatible with the continuing evolution of communication systems. Inexpensive links, whose locations would be accurately recorded, would be exposed by continuous miners during mine entry development, thereby allowing an underground phone to be connected to a surface station in the event of an emergency. A latent network of these communication links could be installed for less than $500 each, minimally affecting drilling and grouting operations, and could be designed to be compatible with many communication devices. This research examines methods and materials for incorporating an embedded communication link during pre-mine exploration drilling, addresses significant factors affecting its implementation, and presents a recommended design. Since mine plans are known to change, the objective is to minimize cost so that, if not used, the investment is minimal for a potential secondary means of communication between the surface and underground workings.

Jan 1, 2014

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By P. Venkatraman

Laboratory and pilot-scale test data have shown that the innovative feed presentation of the CrossFlow separator provides improved metallurgy when compared to traditional hindered-bed or teeter-bed classifiers. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Recent side-by-side industrial-scale evaluations have verified that this technology can improve overall efficiency, reduce the cut point of separation, and increase throughput capacity. This paper describes the important features that make this novel separator ideally suited for size classification and density concentration. Test data from heavy mineral, phosphate, and industrial mineral applications are also discussed.

Jan 1, 2005

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020