Search Documents

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982

By V. Carabias-Hütter, A. J. Basu

The paper aims at promoting sustainability assessment and reporting into practice using a globally acceptable set of guidelines and a common framework for internal and external reporting at a project/site level. Indicators are used for measuring performance, and this paper addresses development and implementation of performance indicators for sustainability assessment and reporting at local as well as global levels. The selection of a proper set of indicators is a challenging task. The indicators selected should provide the expected information for making right decisions. Relevant and credible sustainability reporting supported by a consistent performance indicator system can be the starting point for benchmarking environmental and social performance for the natural resources sector.

Jan 1, 2004

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By John Pekrul

Coeur Rochester Inc. located in north central Nevada, operates an open pit mine moving a total of 16 - 18 million short tons of material per year. A three stage crusher produces approximately 8 million tons of a minus half inch product that utilizes truck stacking to construct a heap leach with a zinc precipitation recov­ery plant. Coeur Rochester recovers approximately 6.0 - 7.0 MM ounces of silver and 60 - 80 K ounces of gold annually. Current metal prices and good operating practices require contin­ued review of operating systems that support the operation, thus the development of a Strategic Mine Plan. This Strategic Mine Plan provides managers, engineers and supervisors a means to improve their operations through three main objectives: 1. Reduce operating costs, 2 .. Increase production, 3. Increase mine life (reserves). These three main objectives will be reviewed in context to their current status and past performance.

Jan 1, 1999

By Paul Chamberlin

Although performing a heap leach test is inherently simple, a lot of information beyond extraction, leach time, and reagent consumption can be obtained from a well designed test program. The following is a list of information to look for and acquire when performing column tests and field heap leach tests.

Jan 1, 1998

By G. F. Raymond

Discussion by G.F. Raymond Knudsen's study presents two curious conclusions: • The kriging of blasthole assays can systematically overstate mill head grades by as much as 21% as a result of unbiased sample variance. • No estimation method is able to reduce this bias to a small margin. The study is based on a simulation using real data and what are presumed to be actual variogram parameters from a real deposit. Although I have no doubt that the first conclusion (21% overestimation) is correct for the author's simulation, I do not believe this represents a realistic mining situation. Over the past 15 years I have done extensive comparisons between exploration drill-hole assays, blasthole assays and mill head grades on seven major open-pit mines, including some very erratic gold deposits. Commonly, nugget effects on blasthole variograms were 10% - 20% higher than on exploration variograms. And in one extreme case, the difference was 50%. Even in the extreme case, ordinary kriging on blastholes agreed well with the mill head grade over the long term. In Knudsen's simulation, the blasthole nugget effect is assumed to be 200% higher than exploration data's. He supports this by variogram plots from each. My guess is that the apparent, large difference between these variograms results from a failure to account for the proportional effect (blasthole assays are likely from a higher-grade area). A simple check would be a comparison of the variance of exploration samples nearest blastholes. As for a nearly conditionally-unbiased estimator of a large random error, the arithmetic mean of all of the data certainly qualifies, provided there is an even data spacing. As a corollary, so does simple kriging, which would include, in this case, a large weighting to the arithmetic mean. Similarly, using a large number of samples with ordinary kriging or indicator kriging would significantly reduce the bias in the case of a large nugget effect for the variogram.[ ] Reply by H. Peter Knudsen Raymond questions two conclusions in the paper. First, he wonders whether a 21 % overestimation represents a realistic mining situation. I agree that 21 % is high, but overestimation in the range of 10% to 15% is certainly common in my experience. Furthermore, several years ago I consulted on a gold mine that was experiencing a 45% overestimation due, predominantly, to poor blasthole samples: In further questioning of the 21 % value, Raymond wonders whether the nugget effect of the blastholes is really so much larger than the nugget values of the exploration data. It is consistently larger throughout the deposit. In my experience with six Nevada gold mines, the high nugget value is not unusual. In fact, for some reason, nugget values for blasthole samples are typically about 0.0005 (opt squared). I am of the opinion that this high nugget effect observed at many gold mines is predominantly due to the inherent inadequacies of the blasthole sample and subsequent sample preparation. The second conclusion Raymond questions is the inability of the estimators tested to reduce the conditional bias. In fact, the conditional bias is extreme with the polygon estimator and greatly reduced by ordinary kriging. However, it was not eliminated. Raymond suggests using simple kriging, or perhaps a larger number of samples, to reduce the conditional bias. The technique of simple kriging may be less affected by the random errors in the data, but I did not test the technique. Using a larger amount of data presupposes that too few samples were used initially. In ordinary kriging and indicator kriging, the screen effect comes into play and ensures that samples beyond the second screen are given zero weight. Hence, increasing the sample size does not change the estimates nor the conditional bias. The main point of my paper is that the random unbiased errors (a fact of life in blasthole samples) cause a conditional bias in our estimates. The mechanics by which the conditional bias is introduced are nicely explained by Springett. My paper simply shows that the bias is also present when working with linear estimators, such as ordinary kriging, and even with nonlinear estimators, such as indicator kriging.[ ]

Jan 1, 1993

By Kevin Bell

The TRAC™ Program was developed to provide our clients with a mechanism that allows them to better manage site remedia­tion and closure costs. This program provides a fixed-price contract for site remediation and case closure and is well suited for large pro­jects with multiple PRPs, such as Superfund sites. Because Kvaerner is a large engineering/construction firm and not a consult­ing firm, we can offer this type of contracting mechanism that envi­ronmental consulting firms are hesitant or unable to provide. With TRAC™, Kvaerner assumes financial and technical responsibilities for carrying a site through the closure process for a fixed price. Liabilities carried on our client's balance sheet for site closure can be removed when they sign up forTRAC™. In many instances, a profit can be realized as the liability on the balance sheet may exceed our TRAC™ fixed-price cost to close the site. Bonds and other sureties securing the site can be released and set­tlement with other involved parties can be quickly reached. For a project to be considered for this program, it typically meets the following criteria: 1) The project site should be physically separated from other contaminated sites 2) A reasonable quantity of site investigation data must be avail­able including site-usage history with or without a projected fea­sibility study(ies) and/or remediation design 3) Access to perform all necessary work must be available. After a review of all site data, K vaerner develops a "risk menu" to manage financial risks. In this "menu", each compo­nent of the project is assigned a level of probability that the costs will occur. Then the base cost of each activity is "weighted" by multiplying the potential cost growth by the probability. This analysis assures that the financial risks are appropriately defined, weighted, and mitigated and a realistic fixed price is developed. Upon acceptance of our proposal and conclusion of contract negotiations, Kvaerner takes over future responsibility for clos­ing your site. This allows the client to: 4) Release reserves obligated on financial statements for the site (and potentially realize a profit if the TRAC™ fixed-price cost is less than our client's booked obligation) 5) Finalize cost settlement with other responsible parties, insur­ers, etc. 6) Redirect resources involved in the environmental manage­ment of the site 7) Cap legal and administrative costs In addition to performing the site cleanup and closure work, at our client's request we are able to: 8) conclude lease obligations for property 9) dispose of equipment and buildings

Jan 1, 1998

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Gordon V. lewis

The Penjom gold mine treats highly preg-robbing carbonaceous ore by using relatively inexpensive gravity and hydrometallurgical methods. The mine is a joint venture between Avocet Gold Limited, a subsidiary of Avocet Mining PLC, a U.K listed mining company with interests in gold and tungsten, and the Pahang State Development Corporation (PKNP) who receive a 2% royalty. The operating team at Penjom embarked on a programme of innovation during 1998 following a realisation that almost all of the primary ore in the gold deposit was highly carbonaceous in nature. Earlier attempts at desliming and leaching the deslimed product through a normal CIL circuit had failed, and through shear necessity, the team turned to new technologies which were considered most suited to the ore characteristics indicated from pre­feasibility testwork. Between April and September, 1998, the mine introduced three key processes, which combined represent the elements of "The Penjom Process". The gravity circuit was boosted to maximise the capture of leachable sulphide and free gold from the relatively carbon free cyclone underflow stream, kerosene and diesel blanking was introduced to treat the cyclone overflow and RIL (resin-in­leach) technology utilised to replace the existing CIL (carbon-in-leach) circuit. Further experimentation with selective resin in partnership with Mintek of South Africa yielded a significant improvement to the process during 1999. Minix­Dowex resin was introduced mid year to replace a non-gold selective resin, which had been used in a flotation/batch leaching circuit for about nine months. Lower carbon levels in the feed at that stage led to the abandonment of flotation and the introduction of continuous RIL, which has been adopted as the major chemical process at the Penjom gold mine since September, 1999. Given the proven performance of the circuit to date, this process may be considered as a low cost option for the treatment of highly carbonaceous ores, particularly those which are not refractory and contain a reasonable percentage of free gold.

Jan 1, 2000

By R. C. Kirkman

Your interesting and well-written paper brings up the issue of the purpose or use of a mineral property appraisal, specifically the value of these evaluations when the quality and quantity of the mineral resource to be exploited have not been thoroughly investigated. I am not a practicing professional in regards to valuation of limestone investment opportunities. I simply wish to make a few generic observations about the appraisal process in order to stimulate meaningful thinking by appraisal professionals whose reports may be reviewed by professional investors and "laypersons" alike. It is my contention that the analysis given in your paper is very thorough, considering the data that was made available to you. But I would not like to be the person responsible for investment decision making without having a feel for the risk involved. Therefore, the reviewer must classify this type of analysis as relatively "subjective" because they have not received an indication of the inherent risk involved in exploiting a mineral resource. This risk can best be quantified by using probabilistic methods in conjunction with the quality and quantity of the mineral to be produced. Most appraisals passively ignore this problem. Specifically, you have accurately identified the various costs and values entering the economic appraisal process. These can usually be quantified with a great deal more certainty than the capability of the resource to provide 25 years of quality material. Also, in Cases A (West Virginia)and B (Alabama), you are fortunate enough to have previous operations data. What if there had never been production from these properties? How does a potential mineral property investor evaluate the resource capability to meet various projected financial outcomes without spending a good deal of up-front capital to drill and delineate enough quality resources for a 20-plus year operation. These questions pose a substantial risk to any potential mineral investor. Only probabilistic methods should be used to quantify this type of problem, short of drilling and metallurgical testing. I might be considered a "layperson," not being familiar

Jan 1, 1991

By W. Z. “Ben” Wu

The investigation provides a method of efficiency evaluation among several kinds of tools employed to cut different types of rocks. A ballistic test stand incorporated with a modified Hopkinson bar was used to simulate a percussive drilling tool. An Apple IIe microcomputer was employed for high speed data acquisition and numerical analysis. A newly developed method for remote monitoring the rock-tool interaction, including contact force, bit penetration and energy transmission,is presented in the paper. Theoretical predictions and experimental results appear in faily good agreement

Jan 1, 1986

By Peter Maltby

A $20M pressure oxidation facility is under construction at the Nerco Con Mine, Yellowknife. Plant commissioning will start in the third quarter of 1992. Roasting of arsenical auriferous concentrates prior to 1970 left 45,000 tons each of highly toxic gold-bearing arsenic trioxide sludge and roaster calcine at the minesite. Safe disposal of these wastes has been a high priority. In 1983 an arsenic trioxide plant was built by the former owner to re-treat the sludge and to sell the product. Due to a poor market and high operating losses, the plant was closed by Nerco in 1989. Mine production in the future will revert increasingly to refractory ore as a replacement for free-milling ore which has been the mill feed since the roaster was shut down. With this fact in mind, Nerco management saw the potential of a proven process to recover the gold from a combined feedstock of refractory flotation concentrate, sludge, and calcine waste. A further requirement was the stabilization of all the arsenic as an insoluble ferric arsenate. By the end of 1989, after the completion of a literature search and a study of process economics, pressure oxidation was selected. Extensive bench and pilot plant work was completed in 1990 and early 1991 to develop the process parameters and to complete environmental testing of the autoclave products. Management approval for construction of a pressure oxidation facility was made in December 1990. Plant capacity is 96 tpd requiring a 40 tpd VSA oxygen plant on site. Detailed engineering began in March 1991. The pressure oxidation building was completed by the end of 1991. The autoclave arrived on site and was mounted on its foundation in December 1991.

Jan 1, 1992

By Paul Higley

Specialty Devices, Inc. and the CMRET/NIUST, University of Mississippi, have collaborated in the design and development of a new class of Robotic Underwater Vehicle (ROV) focusing on efficient, low cost, deepwater operations. The need for such a vehicle was driven by special requirements encountered in the establishment of the Gulf of Mexico Gas Hydrates Research Observatory at a depth of 850m in Mississippi Canyon Block 118 on a restricted budget. Requirements included deployment and recovery of tools and sensors and the connection of underwater-mateable electric and fiber optic connectors at depth. The standard complement of equipment required included; high-resolution video with lighting, scanning sonar, robotic arm, precision positionin and thrusters for limited transit and maneuvering. Conventional deep water ROVs are lowered in a large cage with a buoyant tether between the cage and the ROV. The tether is wound on a winch in the cage deployed as the ROV swims out from the cage. This cage is lowered on a large diameter umbilical cable with strength elements and communications elements and conductors for electric power. With increasing water depth the umbilical cable must become ever larger to accommodate increased power transmission loads and strength demands, with corresponding increase in deck handling equipment size and in turn, vessel size and overall cost. The surface ship must include a dynamic positioning (DP) system to control ship propulsion to maintain the position of the ROV cage at a position relative to the sea floor. DP ships with this capability and the ability to carry the large umbilical cable and winch are expensive.

Jan 1, 2008

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

The Pegasus Gold/Montana Tunnels Mine is a high­tonnage, low-grade, base and precious metal operation in Jefferson City, Montana. Gold heads are typically 0.02 opt with the dominant gold mineral being a native metal electrum quite rich in silver. Early research and development indicated the ore to be amenable to gravity concentration at a 10 to 14 mesh grind. Although full flow gravity preconcentration was considered as a flowsheet alternative, flotation was chosen as the main recovery process due to its apparent lower cost for capital and operating. At this early juncture, the option or concept of recovering coarse free gold by gravity was deemed unnecessary or irrelevant. The intermittent loss of free gold has been observed in the flotation tailing since mill start up. A comprehensive research program was initiated in 1990 to identify the magnitude of this loss and investigate alternatives for its recovery. Batch and pilot plant testing has ultimately led to a permanent gravity circuit being installed at the cyclone underflow. The circuit is designed to scalp out the liberated coarse gold contained in the ball mill circulating load. The final flowsheet consists of: a pinched sluice to upgrade cyclone underflow; a Tyler doubledeck screen to remove over­size from sluice concentrate; Knelson concentrators for roughing and cleaning of screen undersize; an Eriez wet drum separator to remove tramp metal from Knelson concentrate; a Sweco screen to size Knelson cleaner concentrate for tabling; and a Wilfley table to produce final concentrate for direct melting.

Jan 1, 1992

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By R. K. Amankwah, E. K. Asiam

Changes in the thermal-oxidation behavior and other properties of gold-bearing waste activated carbon when milled in both a ball mill and a vibratory mill were investigated. It was found that significant changes occurred in the oxidation temperature of the vibration-milled waste carbon as a result of increases in surface area and mechano-chemical activation. The mechano-chemical action brought about modifications in the crystal structure of the waste carbon. As a result, the vibration-milled sample was completely oxidized at a temperature of 450°C. Thus, the study established that vibration milling is a better way of lowering the temperature of oxidation of the waste carbon. Furthermore, the gold was found to be concentrated in the ash and, when leached with cyanide for 20 hrs, the gold recoveries from a sample having a head grade of 2 kg/t was 99.5% for the vibration-milled sample and 82% for the ball-milled sample. The lower gold recovery for the ball-milled sample was attributed to sintering of the ash, which was caused by the higher temperature required for its oxidation.

Jan 1, 1997

By David Marsh, Mark W. Johns

Carbon-in-pulp (CIP) is a preferred method of gold recovery from cyanided pulp. However, the resin-in-pulp (RIP) process is considered to have several advantages for the recovery of gold. Mintek therefore undertook a research programme to develop a commercially-viable RIP process. The MINRIP RIP process and a novel gold­selective strong-base resin, Minix, were developed. The process has been successfully demonstrated at a scale of 100 000 t/month. Continuous countercurrent tests using synthetic solutions indicate that the relative performance of an adsorbent depends on the composition of the solution. Minix resin yielded a higher gold loading than that of carbon, while maintaining an acceptable barren value. Batch tests on a number of gold-bearing materials indicated that Minix has potentially a higher capacity than carbon, and loads gold faster than carbon. An economic appraisal that consolidated the countercurrent results and the economic study indicated that the capital and operating costs of the Minrip process are considerably lower than those of CIP. The amount of the cost advantage depends on the gold content of the feed and the throughput.

Jan 1, 1993

By G. A. Achilleos

The insufficiency of Boolean Logic and ?hard? decision making to represent and manage spatial data in set with their spatial errors comprises a remarkable difficulty for widely accepted estimation procedures, in realistic planning of space geometric problems and management through a GIS. Fuzzy logic as well as other theories such as the theory of Probabilities, Bayesian theory etc., contribute substantially towards this direction. Data are accompanied by their accuracy and are managed through the applications and modules of Spatial Analysis, aiming to access a decision with known accuracy and fuzziness. As it concerns the cases of waste sanitary landfill sites designing, which are based on the construction of a bank, the problem shown by this paper, seems to be quite serious. The determination of the theoretical waste disposals body in the landfill is based on an uncertain Digital Elevation Model (DEM). As this model is a result of a procedure enclosing errors and inaccuracies, it is for certain a non - error free model. Thus, the geometric computation of the excavation quantities and the waste disposals solid body volume, misquotes the expected standard theoretical computation and imports the need to decide and set a risk level for the project.

Jan 1, 2005