Search Documents

By William M. Hartzler

The Powder River Basin (PRB) refers to the coal deposits located in southeastern Montana and the northeastern Wyoming counties of Campbell, Converse, Hot Springs and Sheridian (Wyoming PRB). In 1993, there were 20 active surface mines with 3109 employees in the Wyoming PRB (Annual Report, The State Inspector Of Mines Of Wyoming, 1993). Early PRB production growth was primarily in response to the passage of the Clean Air Act of 1970. The disproportionate growth in Wyoming as compared to Montana can be attributed to the differing coal taxation policies of the two states. The state severance and production taxes were significantly lower in Wyoming. However, Montana passed legislation in 1987 reducing the severance tax rate, substantially narrowing the severance tax gap. Campbell and Converse counties in Wyoming have benefited the most from the production growth in the region. Cyprus Amax's Belle Ayr Mine, south of Gillette, in Campbell County, was the first modern commercial coal mine to be developed.

Jan 1, 1994

By E. Watkins, V. Gangrade, P. Zhang, J. Addis, D. W. H. Su, T. Minoski, C. Hollerich, M. Van Dyke, S. Schatzel, H. Dougherty

"This paper presents the results of a comprehensive study conducted by the Centers for Disease Control (CDC), National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) to evaluate the effects of longwall-induced subsurface deformations and permeability changes on shale gas well integrity and safety under shallow cover. NIOSH researchers selected a study site over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under 482 feet of cover. One in-place inclinometer well and three permeability monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the inclinometer well and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the first 1,500-ft-wide longwall panel on the south side of the abutment pillar mined by the site.A number of FLAC3D finite difference simulations (Itasca Consulting, 2017) were conducted to estimate surface subsidence, coal pillar pressure increases, and horizontal displacements in the in-place inclinometer (IPI) monitoring well. Comparisons of the FLAC3D finite difference simulation results and the surface, subsurface, and underground instrumentation results show that the measured IPI casing deformations are in reasonable agreement with those predicted by the FLAC3D models, and that the measured surface subsidence and underground pillar pressure are in excellent agreement with those predicted by the 3D models. Measured permeability changes were incorporated into a preliminary calculation to evaluate the effect of a hypothetical shale gas well leak on longwall ventilation. Results from this 2018 research clearly indicate that under shallow cover, the measured horizontal displacements within the abutment pillar are at least one order of magnitude higher than those measured in a 2017 study under deep cover and slightly higher than those measured in a 2014 study under medium cover. This research represents a very important step and initiative in utilizing the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the workers in the oil and gas industries"

Jan 1, 2019

By Andrew J. Neale, Mark Franklin, Mike Cooper

Although recent advances have significantly improved our understanding of flotation fundamentals, disturbance variables combine to make it difficult to maintain steady state operating conditions over either the short or long term. One of the major concerns relates to knowing how much reagent to add to the flotation system, how to monitor the addition rate, and how to determine when to adjust the reagent addition rate in the presence of these disturbances. This paper will look at the development and installation of process control systems that address these issues. The economic benefits that accrued from the implementation of these strategies is described.

Jan 1, 1994

By Lane White

Loading shovels are at the heart of most surface mine production. As truck sizes have increased, shovel manufacturers have matched them with larger shovels (see table, page 343). Further increases in shovel size may be in order if trucks in the 270-t (300-st) range find acceptance at the largest surface mines. However, larger shovels are not currently the primary focus of shovel design engineers. Competition and user pressure are combining to keep their work directed toward improved shovel productivity and efficiency. Computer design technology and advanced electronics play an increasingly prominent role in this work. "Improved diagnostic capability, system monitoring, vibration analysis and above all increased user friendliness in machine control systems are being pursued by most manufacturers working in our industry today," observes Stuart R. Cotterill, director of marketing for Harnischfeger Corp. The use of computer-aided design (CAD) systems in shovel design has been in place for many years. However, recent advances in computer capability and improved software programs and graphics are making computers even more useful.

Jan 1, 1995

By D. Royston

Curved pulp lifters can provide improved discharge performance from SAG mills, especially for the coarser fraction of rocks in the discharge. They also can provide improved wear life of the pulp lifter, especially the base of the pulp lifter and diversion cone, over comparable straight radial pulp lifters. Current experience with curved pulp lifters and associated grates is covered including design issues and discharge performance for both the slurry and rock components of the discharge.

Jan 1, 2003

By Paul D. Chamberlin

The evolution of heap and dump leaching has followed the development of agglomeration, materials of construction for leach pads and ponds, solution distribution systems, testing techniques, and state regulations. They are now mature processes. Possible future directions and developments are discussed. In situ leaching of precious metals is waiting to be commercialized. Regulators are reluctant to allow the use of cyanide because of the potential for excursions and operators are reluctant because of the potential for lawsuits. Developments in alternative lixiviants are needed before in situ leaching is accepted.

Jan 1, 1989

The new generation of computer environment provides mineral processing plants with convenient tools to store and retrieve or to analyze on-line process variable values as given along time by the various sensors installed in the plant. The paper describes the application of classical tools, such as time series analysis, to retrieve the hidden information contained is such data. The concepts used in single signal processing (autocorrelogram, power spectrum, ARIMA descriptors) and multi-signal processing (cross-correlogram, cross-spectrum) are briefly reviewed. Some examples are given to illustrate their application (sampling, data filtering, process behaviour prediction, process evaluation, data synchronisation). Examples are taken from mixing, flotation and leaching processes.

Jan 1, 1990

By George M. Potter

Precious gold and silver markets support substantial activity in the search for and development of improved and unconventional ore and tailing processing methods. The need for such methods 1s strengthened by consideration of increasingly low grade and refractory ores and old tailing reserves. As background for this review of new and unconventional precious metal processing, recent USBM data (1981) show annual world gold production of about 40.8 million troy ounces. In the U.S. about half the 2.8 million ounce consumption was used for jewelry and the arts, 39 percent for industry, and 8 percent for dental purposes. World silver production in 1981 was about 365 million ounces. Domestic usage the same year was about 117 million ounces. More than $ was used for photography and 30 percent for electrical and electronics. By process, about 1 percent of U.S. production of gold came from amalgamation, 66 percent from cyanidation, 31 percent from smelting ores and concentrates, and 2 percent from placers. As for silver, about 11 percent is from cyanidation and 89 percent from smelting ores and concentrates. Evidently the search for innovative and unconventional precious metal processes must include gravity concentration, froth flotation, hydrometallurgical, and electrometallurgical methods. Although smelting processes are equally important, they largely comprise nonferrous metal technology, and are not discussed here.

Jan 1, 1984

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By D. Koch

Bentonites and bentonite containing sealing materials are used since many years for sealing purposes in foundation, dike construction, hydraulic engineering and landfill construction, especially for encapsulation of old waste deposits In the near future compacted bentonites will be important components of multi-barrier systems for dry charge of old mines, for underground disposal of hazardous or radioactive wastes. Because of their exceptional physical, structural and chemical properties, bentonites are offering manifold possibilities to protect the environment against the negative effects of dumping grounds. Often the compliance with legal regulations for waste dumping or the isolation of contaminated areas is possible only by using bentonite containing sealing systems. The essential properties of bentonite, bentonite containing building materials and the different techniques of making horizontal technical base liners and vertical cut-off walls are explained. For horizontal technical base liners the adsorption ability, the ion exchange capacity and the swelling behavior of bentonites are important. For cut-off walls bentonite controls the rheological behavior of the slurry and is responsible for the low permeability of the hardened bentonite-cement-wall. In the multi-barrier systems of repositories for chemical or radioactive wastes compacted bentonites are considered to be favourable sealing and backfilling materials because of their high swelling capacity, their adsorption and ion-exchange ability and their plasticity in water saturated state.

Jan 1, 2005

By E. J. Meets, C. F. Meyer

Bord and pillar mining at shallow depth (400 m approx. maximum) is widely used in South African coal mines. One of the problems encountered in extracting coal in this manner is the ventilation of advancing bord and pillar headings. The traditional ventilation methods of force, exhaust and overlap (force/exhaust) are reasonably effective but tend to be both cost and labour intensive. Ducting often restricts the available free area of roadways thus impeding the transport of coal and other materials inbye the coal production section. Due to the above facts, ductless fans are currently being used to minimize the amount of ducting required in advancing sections. Two different types of fans are used, namely, vortex fans and the so-called `jet' fans. Vortex fans were developed from the fan blade design used for vertical take-off aircraft. The fans have the capability of delivering air over distances of about 30 m in the underground situation without any ducting attached to it. Jet fans are standard axial flow fans fitted with outlet reduction pieces which increase the velocity pressure at the discharge to such an extent that the air delivery distance is improved to almost match that of vortex fans. The paper describes some applications of both these fan types in advancing bord and pillar sections.

Jan 1, 1993

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By Kenneth N. Han, Yuhong Chen

The removal of carbonaceous material from Carlin gold ore has been investigated via froth flotation. The effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material has been studied. Other variables affecting froth flotation efficiency were also examined closely. These included particle size, pH of the solution, and temperature. The effect of reduction and oxidation of carbonaceous material on froth flotation efficiency has also been investigated. This investigation showed that aromatic type oil was the most effective collector. Also found in this investigation was that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation. More than fifty percent of the carbonaceous material was able to be removed via froth flotation. It can be concluded from this study that the effect of pH and temperature during the rougher flotation state is of little significance to the overall recovery of carbonaceous material. Since pyrite is responsible for the high consumption of chlorine, removal of pyrite is very important in order to reduce the overall consumption of chlorine.

Jan 1, 1990

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By S. K. Kawatra, T. C. Eisele

Microorganisms, such as the bacteria Thiobacillus ferrooxidans, have been reported to depress pyrite flotation (Elzeky and Attia, 1987; Atkins, 1990). However, the depen¬dence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms (chemolithotrophic bacteria, chemoorganotrophic bacteria and yeast) over the pH range of 2 to 12 was studied. Screen¬ing tests using microflotation showed that every microorgan¬ism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with both mineral pyrite and coal pyrite using Thiobacillus ferrooxidans and Saccharomyces cerevisiae as depressants, showed that these microorganisms are very effective depressants for mineral pyrite at acid pH, but they are largely ineffective at neutral and alkaline pH, where the mineral pyrite surface is not naturally hydrophobic. The flotation response of the coal pyrite was completely different from the mineral pyrite. The coal pyrite was most floatable near neutral pH, with the floatability decreasing in acidic or alkaline solutions. De¬pression of the coal pyrite by yeast was not selective between the pyrite and the associated coal under the experimental conditions.

Jan 1, 2000

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974

By H. J. Sandri

In the spring of 1991, Western Aggregates, Inc. began operating the newest expanded shale lightweight aggregate operation in North America. The operation is located in Jefferson County, Colorado, just south of Boulder, at the sight of the former Ideal Basic Industries ("Idealite") lightweight aggregate plant, which was decommissioned in 1975. The "new" facility has been built to principally serve the Denver and Front Range markets, as well as ship products into other locations in Colorado, Wyoming, New Mexico, Kansas and Nebraska. Western Aggregates is a wholly-owned subsidiary of Inco U.S., a subsidiary of Inco Limited of Toronto, Canada. Inco Limited is the free world's largest producer of nickel and is a leading producer of copper, cobalt, gold, silver, and platinum group metals, high nickel and super alloys, and specialized engineered products. Inco is constantly seeking new mining related investments that leverage off its mining and processing skills and that meet corporate fmancial objectives. Construction materials are an area presently being pursued by Inco. The basic 'building blocks' of society, from a construction perspective, are sand and gravel, stone, and aggregates. To the vast majority of people these are natural products that are mined, quarried or dredged, and other than washing, screening and crushing, are generally used in their primary form. While these materials vary from quartzite river rock, to calcified limestone, to hard basalt, they are generally classified as "heavy" aggregates. There are, however, other types of aggregates that do not fall under the "heavy" classification, but are used in general construction activities just the same.

Jan 1, 1992

By V. Srivastava, T. Ghosh

"Modeling and Simulation of SAG Mill has been widely used in design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. This paper attempts to characterize mill contents by solving Whiten’s first order contents based model in Matlab/Simulink environment. The parameters in the model such as breakage rate (S), discharge rate (D) and appearance function (A) were estimated utilizing process and design data collected from a gold mine operating in Alaska coupled with nonlinear parameter estimation scheme. This model is then utilized to predict dynamic response of other key operational variables such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated utilizing dynamic response data from the plant to encompass operational characteristics of SAG Mill behavior. Keywords: SAG Mill, Dynamic Modeling, Simulation, Nonlinear Parameter Estimation. INTRODUCTION Grinding in mineral industry is one the most important steps in the process of size reduction and plays a crucial role in determining the overall economics of the milling plant. Much of the efforts focused on improving the process efficiency using modeling and simulation have been practiced by researcher and engineers. However, up till now these models were simulated under steady state approximation because of their complex nature and difficulty in programming them in a dynamic framework. Steady state simulations have been successfully utilized in circuit designing, capacity planning and pre-flowsheet optimization. The maturity in steady state models is because of its applicability and regular use in steady state simulation packages such as JKSimMet, Limn, ModSim, etc. With the advent of equipment such as SAG and AG mill has been a recent shift in the simulating these models using dynamic approach. Because of the economic benefits of these devices and ability to act both as a primary grinding device and as secondary or tertiary crushing device they have gained a large popularity and are now universal to any milling plant. However, these device poses a real challenge to engineers and researchers in terms of operation and control. The major reason attributed to problems faced is because the ore constitutes the major portion of the charge in these devices when compared to ball and rod mill. This rock charge is subjected to disturbance such as changes in feed size distribution and ore hardness which results in unstable operation and frequent mill stoppages. One way to prevent this is to measure and control these external variables, however, lack of available instrumentation and unavailability of sensors to measure these variables has foiled the understanding of complete process occurring inside the mill thereby, inhibiting development of proper control system."

Jan 1, 2017

By Valcana Stoyanova

The distribution pattern, abundance variations and types of polymetallic nodules and associated megabenthic communities in area covers more than 60 000 km2 laid out in the eastern Clarion-Clipperton Zone (CCZ) is presented. Our observations are based on data from 158 boxcore stations collected during the cruise of the Interoceanmetal (IOM) in 2004 on board of RV Yuzhmorgeologiya. Although those polymetallic nodules for two decades been subject to prospecting and exploration studies carried out by IOM, the knowledge of megabenthic communities and their distribution pattern within nodule field was extremely limited. With purpose to evaluate the relationship between polymetallic nodules and associated benthic megafauna, an comparison analyze was carried out in respect to their composition, types, abundance across the studied area owing into account the local particular feature of bottom topography. It is suggested that the nodule-bearing seafloor supported more diverse fauna (higher number of morphotypes) than the nodule-free areas. Moreover, based on correlation between types of nodules and associated faunal morphotypes frequency the apparent relationship is considered. The most abundant megafaunal taxa (between 68 ? 92%) is essentially associated with the occurrence of the diagenetically growth nodules type (D-type and its D1-subtype); the role of the H and HD nodule-types was variable. In respect to the bottom topography, the highest diversity in the structure of megafaunal communities was recorded in the gently undulating plains and on the horst slopes, thus the highest nodule abundance occur on the topographic slopes.

Jan 1, 2008

By Paul J. Lauricella

This presentation will summarize the basic safety components of an underground safety program. The program will begin with the first ingredient to a successful safety program, top management support, and continue through emergency services. Particular attention will be devoted to top management support for the safety program.

Jan 1, 1985