Search Documents

By Calvert D. Iles

Open-pit mines in the US and throughout the world are typically characterized by increasing operating costs and decreasing ore grades. Thus, companies must continue to improve their use of human and technological resources to remain competitive in the marketplace. Duval Corp. has historically been very sensitive to mining costs, in part because of relatively low grade copper-molybdenum ore bodies. These concerns have resulted in three haulage system generations at the 218 kt/d (240,000 stpd) Sierrita-Esperanza open-pit mine south of Tucson, AZ. Each generation has exceeded the performance of the one replaced. The latest system of portable crushers and conveyors reduces hauling costs by combining both hardware and technique. Savings are achieved not only bysubstituting conveyors for haul trucks, but also by permitting the crusher-convey or system to closely follow mining as the pit deepens and/or mining areas change location. The Duval system is capable of easy and inexpensive relocation in varying site configurations in relatively short time periods. Its implementation in active mining areas results in minimum disruption to both the mine operation and mine design. This haulage concept allows the mining engineer maximum freedom to design an open pit for profit rather than for equipment. Maximum savings with a portable system are achieved by minimizing truck haulage costs. At Sierrita, for example, the yearly estimated operating cost savings for each thousand feet of +10% truck ramp replaced by conveyors is about $1 million per portable crusher. A savings of $30 million could be achieved fora three-portable system overa 10 year period simply by reducing the average truck Iiftto the crusher by 30 m (100 ft), There is also the added capital expense of buying trucks to cover the additional 30 m (100 ft) of lift. Relocation costs are an important consideration in a portable system. Direct costs can become a significant operating expense if frequent relocations are necessary to take full advantage of potential haulage cost savings. A site preparation cost of $375,000, for example, would add an additional operating cost of 2.8¢/t(2.5¢/st) for a system handling 13.6 Mt/a (15 million stpy), assuming one move a year, In addition to the direct cost of site preparation, such as installation of retaining walls, apron feeder slots, and equipment pads, there is the cost of site renovation after abandonment. Indirect relocation costs, while less tangible and more dependent on specific mine design and scheduling, can be of significance. A slowdown in the mining rate or a less efficient mining plan can result from a site not being immediately available for mining after abandonment. Conversely, mining in narrow areas can be adversely affected if two or three month lead times are required for site preparation.

Jan 4, 1983

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By S. N. Groudev

Acid mine drainage waters generated in the uranium deposit Curilo, Bulgaria, were treated by means of a pilot-scale passive system consisting of an alkalizing limestone drain, a permeable multibarrier for microbial dissimilatory sulphate reduction, biosorption and chemical neutralization, and a natural wetland, connected in a series. The waters had pH in the range of about 2.5 ? 4.1 and contained radionuclides (uranium, radium), heavy metals (copper, zinc, cadmium, lead, nickel, cobalt, iron, manganese), arsenic and sulphates in concentrations usually much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The water flow rate through the passive system varied in the range of about 5 ? 15 m3/24 h, reflecting water residence times of about 60 to 20 hours. An efficient removal of pollutants was achieved by this system during the different climatic seasons, even during the cold winter days at external air and water temperatures close to 0°C. The removal was connected with different mechanisms but the microbial sulphate reduction played the main role during the warmer months of the year. However, during the cold winter days the removal of pollutants was due mainly to their sorption by the solid dead plant biomass (cow manure, plant compost, straw) present in the multibarrier as well as to their precipitation as a result of chemical neutralization caused by crushed limestone.

Jan 1, 2006

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber, etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by the adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. To develop a scientific basis for the selection of the appropriate modifiers it is necessary to understand their adsorption mechanisms. specifically, the adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for nonionic polymers. However, a literature survey of the Poly(ethylene oxide) (PEO)-oxide system suggested that PEO, a nonionic polymer, was substrate specific. A systematic study was undertaken to investigate the adsorption mechanisms of PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work, characterization of PEO binding sites on oxides is reported and the mechanisms of PEO adsorption are discussed.

Jan 1, 1999

By Athorn Mary-Lee, Randall A. Snowdon

During the development of the Selby Coalfield, UK, a Robbins full-face tunnel boring machine (TBM) and a Thyssen Titan roadheader were used to drive a pair of parallel spine roadways. This paper presents a summary of the comparative operational and cutting performance of both the Titan road- header and the Robbins TBM. Statistical techniques were employed to identify relations between machine performance and geotechnical parameters.

Jan 1, 1986

By A. I. A. Salama

A computationally efficient technique for generating a balanced set of density or size separation data is developed. The technique proposed utilized minimization of a modified form of error squares to generate the optimum estimates of outputs mass yields (splits) and balanced direct mass distributions of feed and outputs. The estimated separation data set satisfies mass balance conditions of the streams mass distributions around the separator. The technique proposed avoids the generation of small negative values for the estimated feed and outputs direct mass distributions. Actual data are used to demonstrate the technique proposed.

Jan 1, 1996

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By Selamet G. Ercelebi, Mahmut Yavuz

An inherent aspect of longwall mining is moving the equipment from a mined-out panel to a newly developed panel. Moving times may be reduced by detailed preplanning. A very useful tool for planning is MS Project. Using MS Project, one can efficiently plan, manage and coordinate a project from conception to conclusion. The critical path analysis identifies potential critical activities which may cause excessive time delays. Changes to the tasks on the critical path can have significant impact 0.n the completion of a project. Assigning additional resources to these tasks (either moving labor from other tasks to critical tasks or providing labor overtime work) may reduce the move time. Simultaneous activities are the candidates for moving the labor from an activity to another. Each time a change is made, the critical path should be recalculated. MS Project quickly recalculates schedules and lets you see how changes in one part of the project will affect the overall plan. In this fashion it is possible to minimize the longwall move time.

Jan 1, 2002

By Anthony Delvescovo, Gregory F. Aluce, Joseph A. Sopko, Lyle C. Smith

Construction of a 13m shaft through approximately 100m of water bearing soils and another 100m of bedrock was attempted using the Slurry Diaphragm Wall Method with a combination of deep dewatering wells. During excavation within the slurry wall, unexpected groundwater inflows occurred in a structure of loose silty sands. Artificial ground freezing was selected as a remedial method to seal the leaking slurry wall, and as a primary excavation support and groundwater control method for the 30m of overburden material below the base of the wall. Design of the ground freezing system required analysis of both the structural requirements of the unsupported soil, the frost effects against the existing slurry wall and the groundwater control in the area of the breech in the wall. These design procedures are summarized, and construction and excavation techniques and corresponding schedules compared in this paper. Advanced drilling techniques, ground freezing quality control and general contractor procedures for efficient shaft construction are discussed.

Jan 1, 1993

By L. Landryova

The Department of Control Systems and Instrumentation, VSB - the Technical University Ostrava, has been involved in a project dealing with utilization of landfill gases, when the methane gas utilization and minimization of its release into the atmosphere was the main concern. The landfill site is generally a place, where technology for energy production can be built. The conditions for this technology implementation vary and depend on various factors. This paper is presenting findings and experience gained regarding a method of methane gas utilization for energy production. This method is concerning building bioreactors at the landfill sites, which are already operated. Every bioreactor can be thought of as a process, which is controlled in order to maximize energy production and minimize the methane gas escape into the atmosphere. The bioreactor landfill can represent a number of environmental and cost savings and, at the same time, is able to comply with all legislative issues.

Jan 1, 2005

By Vernon Miller

In 1986, a subsidiary of Echo Bay Mines Ltd. purchased the McCoy property, 55 km (35 miles) southwest of Battle Mountain, NV. Echo Bay then launched a two-year, $1 15-mil lion capital program to build a mill to extract gold and silver from high-grade ore mined in two open pits - the original McCoy pit and a more recent discovery, the Cove. Engineering on a new mill began in 1987 with the facility coming on line in 1989. It was comprised of a semiautogenous (SAG) mill and ball mill grinding, leaching, flotation, counter current decantation (CCD) and Merrill-Crowe processes. The mill started up on McCoy ore, a rocky material that settled very well in the new CCD thickener system. Production levels were maintained at about 7.2 kt/d (8000 stpd). The situation changed as the McCoy ore played out and increasing amounts of material from the Cove pit-with its oxide, sulfide and carbonaceous ore - were fed to the mill. The problem was the high clay content of the Cove ore. The new ore immediately created production problems, mainly loss of control on the CCD thickeners. With the McCoy pit slated to be shut down in early 1991, it was essential to find a way to efficiently process the Cove ore. Initially, the only way to regain control of the thickeners was to slow down the processing rate and increase flocculant usage, thereby getting the solids to settle in the thickeners. But this had its cost. Production dropped to about 5.9 kt/d (6500 stpd), additional operators were needed and flocculant costs, on occasion, would reach an unacceptable $80,000 per month. Overfloccing led to viscous

Jan 1, 1993

By G. T. Adel, W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphulerite and dolomite, has been used to experimentally validate the model for the case of dry batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1988

By J. R. Sturgul

Computer simulation models of working mines can be a great benefit to mining engineers. Such models have been used in mine planning (how many trucks-shovels to have, when to add new equipment, etc.) and mine design (should a dispatch system be purchased, where is the optimum location, for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine. It can be easily changed to reflect a variety of situations. A major problem for the engineer is how to present the results of the simulation study. This has now been overcome by means of animation to present the results of the simulation. The main simulation languages in use for discrete system simulation are SLAM, SIMAN and GPSS/H. Each has animation with SLAMSYSTEM for SLAM, CINEMA for SIMAN and PROOF for GPSS/H. Animation with SLAM and CINEMA have been on the market for several years whereas PROOF is a relative newcomer and has features not found in other animation software. This discussion will be confined to PROOF. Some of the comments will apply to all simulation and animation software.

Jan 1, 1995

By A. M. Elmherig, M. R. Sunu, R. N. Singh

The presence and orientations of fractures and discontinuities in rock masses exposed in a surface mining excavation are likely to have a great influence on both slope stability and blasting efficiencies. The classification of rock materials requires detailed investigations which are of interest to the design engineer. In designing a safe mining excavation, an engineer must take a number of decisions regarding face support and orientation based on the evalu¬ation of local strength and structural conditions encountered. The description of rock masses requires information additional to the properties of the rock material, discontinuities and other characteristics of engineering importance. Such information involves the acquisition of the following data: The description of the rock mass with reference to major geological structures. The orientation, nature, spacing and persistence of discontinuities. Degree of weathering. A critical review of rock mass classification systems and their application to surface mine excavation design and stability analysis is presented. The field investigation techniques for collecting rock mass data are described together with the techniques of analysis and presentation of data. Laboratory tests are carried out to determine intact rock strengths and deformation parameters of rock. The paper presents two case studies from the British hard rock surface mining industry to illustrate the application of the rock mass classification systems to stability analysis and excavation design.

Jan 1, 1986

By C. J. Veal, C. I. House, S. R. Bellamy

INTRODUCTION Coal gold agglomeration (CGA) is a new concept in gold processing. It involves the recovery of oleophilic (oil-loving) gold grains by causing them to adhere selectively to the surfaces of coal oil agglomerates. Under optimum conditions very high recoveries of gold. can be achieved. The agglomerates are recycled to build up gold loading to typically 1000 - 5000 g/tonne. Bullion can be produced by burning the loaded agglomerates with subsequent recovery of gold from the highly loaded ash either by dissolution/electrowinning or smelting. A wide-ranging programme of laboratory testwork has been performed to investigate the response of different ore types to the process. This has shown CGA to be most applicable to ores in which the gold is liberated or easily liberatable, relatively coarse (ca 500 µm) and fine (<5 µm) gold grains being recoverable with equal ease. The best opportunities for CGA seem to be: • placers containing fine gold not recoverable by gravity concentration • low grade gravity concentrates to avoid multiple magnetic/gravity separation stages and amalgamation • free milling ores where the gold can be liberated at a reasonable ore particle size eg >d80 50 µm • tailings past or present from gravity concentration plants. CGA testwork ranging in scale from laboratory to pilot plant on tailings produced by gravity concentration in the 19th century Australian gold rush has already been reported (Bonney, C F, 1988; House, C I, Townsend, I C and Veal, C J, 1988). An economic appraisal for a Canadian free milling gold ore has also been published (Buckley, S A, House, C I and Townsend, I G, 1989). This paper describes results of a detailed laboratory programme to assess CGA as a means of recovering gold from a beach sand deposit in New Zealand. The area from which the samples were taken consists of quarternary interglacial marine, lagoonal, fluvial and eolian deposits. The heavy minerals present are predominantly ilmenite and garnet and small concentrations of gold. In certain locations the sands and gravels are consolidated by a limonitic cement. In the 19th Century some parts of the deposit were mined and the ore processed using stamp milling and gravity concentration. Gold recoveries were low, probably below 50%, due primarily to the fine size of the gold grains, the flaky nature of the gold and also imperfect liberation by the stamp mills. Our laboratory testwork was divided into three parts: i) Preliminary studies on an initial sample to assess the feasibility of treating the ore by CGA ii) Extended studies on further samples from various locations in the deposit to confirm predictions from (i) iii) Conventional gold recovery techniques. EXPERIMENTAL PROCEDURES All CGA tests were performed by agitating a slurry of ore in water in a 0.6 dm3 pyrex beaker fitted with four vertical baffles. When required, potassium amyl xanthate collector was added and the slurry conditioned for 5 min. Coal (ex BP Coal Australia&apos;s Tahmoor Colliery) previously ground to a d80 50 µm was added followed by a commercial grade of gas oil (density 840 kg/m3). The agglomeration time was 30 min. The agglomerates were separated from the tailings by screening, both were then dried and analysed for gold by fire assay. This test procedure provides a reasonably accurate estimate of gold recoveries that might be expected from our 1 tph pilot plant. Ore samples were ground either dry in an agate ring disc mill or wet in a steel batch tumbling

Jan 1, 1989

By J. Devon, D. L. Ewart

Long-term coal mining plans are often based on attainment of an average cost of coal. This is achieved by blending low- and high-cost coal production. Coal that is beyond the economic limit of the reserve is mined in a misguided effort to improve reserve recovery. Long-term contracts should be least cost-based and generate the best net present value from the economic reserve within the context of a rational mine plan. The selected economic reserve should he mined on a low- to high-cost basis to benefit from the time value of money.

Jan 1, 1996

By L. W. Saperstein

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence-function-based computer program. Using an inverse application of the traditional influence-function technique, easily obtained surface displacements are used to analyze some of the complicated, expensive, and difficult-to- measure movements of the intermediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A secondary hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge-effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria, and in situ measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1988