Search Documents

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930's. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984

By D. S. Bird

Kennecott Utah Copper began a modernization program in 1986 that was aimed at expanding and updating mining and ore process facilities at the company’s Bingham Canyon copper mine and concentrator near Salt Lake City, UT. Major components of the project included installation of an in-pit crusher, a transfer conveying system and a new ore concentrator with a design capacity of 70 kt/d (77,000 stpd). The Copperton concentrator was commissioned in February 1988. The grinding circuit is one of its principal features. It consists of three identical lines, each with a 10.4-m- (34-ft-) diam x 4.6-m- (15-ft-) long semiautogenous grinding (SAG) mill and two 5.5-m- (18-ft-) diam x 8.6- (28-ft-) long ball mills. The SAG mills are driven by two 4.5-MW (each) (6000-hp) variable- speed dc motors through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4.1-MW (5500-hp) synchronous motors coupled through a typical clutch-pinion gear-ring gear system.

Jan 1, 1995

By Frank K. Mattson

The Minerals Processing Section of Surface Combustion is currently engineering and erecting a plant designed to produce 400,000 LTPY of 95% metalized pellets from raw magnetite concentrate, This venture is the first domestic commercial facility that will manufacture pre-reduced pellets as an integral part of a process to produce steel. Surface Combustion has developed the methods that will be used. Midrex, a division of Surface Combustion's parent company, Midland-Ross, will own and operate this plant. The site is adjacent to the City of Portland, Oregon on a 15 acre hydraulically-filled area on the east bank of the Willamette River. Either filter cake or concentrates in slurry form will be purchased from Marcona in Peru, delivered to the dock facility by ocean vessels and distributed to a pond for wet storage. Reclamation from the pond will be with a conventional dredge delivering concentrate to a thickener.

Jan 1, 1968

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By John W. Rozelle, David S. Bolin

INTRODUCTION During the normal course of a mining project, a feasibility study will be prepared that addresses all the aspects of the project including geology and mineral inventories, mining and geo- technical, metallurgical processing, infrastructure, environmental considerations and economic analyses. These studies are prepared for various reasons. Occasionally, a feasibility study will be prepared solely for use within a company as justification for development expenditures, however, these documents are frequently submitted outside the company either to raise funds from financial institutions or from public financing on one of the various securities exchanges. Mineral industry consultants are often called upon to participate in the preparation of feasibility studies or to conduct an independent audit and review of an internally prepared study. As the recoverable mineral resources form the foundation upon which the balance of a feasibility study is based, including the economic analysis of the project, the resource aspect of the study is examined very carefully by financial and securities organizations. The balance of this discussion is directed toward the various geological and resource estimation aspects of feasibility studies that experience has shown to be of particular importance. Much of this discussion will be directed toward open pit gold operations, although the principles are applicable to any type of deposit. 2.0 GEOLOGIC RESPONSIBILITIES IN FEASIBILITY STUDIES The principal geological effort in the preparation of a feasibility study is generally dedicated to the following areas: - Preparation of Geologic Reserve/Resource Estimates - Condemnation of Sites for Facilities, Access Roads, Leach Pads, Waste Dumps and Tailings Disposal - Collection of Geotechnical Data - Provision of Mineralogical and Petrological Data Pertinent to Metallurgical Processing - Selection of Appropriate Bulk Sampling Sites for Collection of Metallurgical Samples Each of these items will be addressed in detail in the following sections. 3.0 RESERVE/RESOURCE ESTIMATION An ore reserve estimate consists of the determination of a volume, or tonnage, and a grade for the deposit. There are numerous cases in the mining industry of projects that have experienced severe difficulties when operational ore grade, tonnage or metallurgical amenability have proven to be deficient compared to predicted estimates. An error in estimation of tonnage generally leads to more long term problems affecting mine life and production schedules. However, a significant error in the estimation of grade, particularly if mined grade is lower than anticipated, can have an immediate, and often disastrous, effect upon a project. The geologic preparation leading to an ore reserve estimate generally follows a logical sequence familiar to

Jan 1, 1987

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By R. M. Rowe, A. K. Bhasin, D. Malhotra

Introduction Most primary molybdenite producers use a selective flotation process in which molybdenite is floated from the ore while other sulfide and nonsulfide gangue minerals are depressed in the same step. The process was developed at the Climax mill. Reagents used in the rougher flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother), and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide, and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born et al. (1976) and Malhotra et al. (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50% of the total molybdenite flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors that would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate nonoil-based collectors and collector systems that are less expensive than vapor oil. A series of potential nonoil-based collector classes were identified and evaluated in the laboratory against the current collector system. The metallurgical performance of these collector classes was related to their chemical structures. The results of this study are discussed. Collector classes A survey of sulfide mineral collectors was performed with the objective of identifying and selecting potential collectors for molybdenite flotation. The available reagents were categorized into 10 general classes. Table 1 summarizes these collector classes, their chemical formulas, the manufacturers, and selected commercial collectors in each class that were evaluated in the present study. Experimental procedure A Climax ore sample, assaying 0.3% MoS2, 2.2% FeS2, 0.007% Cu, 0.003% Pb, and 0.03 oz per ton Ag, was used for this study. Standard laboratory rougher flotation test procedure involved grinding a 2-kg ore charge in a rod mill at 60% solids. Reagents were added to the rod mill including a collector, syntex (0.005 kg/t), pine oil (0.03 kg/t), lime (to adjust pH to 8), and sodium silicate (0.15 kg/t). The ground pulp was transferred to a 1000-g cell, and flotation was performed at 35% solids and 1800 rpm using a Denver D-1 flotation machine. Concentrate was collected for a flotation time of six minutes. The general approach used in the present study was to substitute the nonoil-based collectors at two to three different dosage levels (0.01 to 0.15 kg/t) for vapor oil in the bench-scale, open-circuit rougher flotation tests

Jan 1, 1987

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By R. L. Grayson, Y. J. Wang

An integrated approach to the management of underground coal mine production and cost is presented. A conceptual model for objectively analyzing an underground mine to obtain lower cost and higher productivity from operations is outlined. The model is designed to provide mine managers with a quantitative, decision-assisting methodology that can be used in formulating timely responses to fluctuations in operations. It consists of a productivity fore- cast component, routine use of current resource consumption factors, a linear programming scheduling component, a manpower loading analysis, and an inventory control component. The model is applied to an underground coal mine.

Jan 1, 1990

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By Slavoljub D. Maksimovic, Steve J. Page

The Bureau of Mines measured respirable dust emission rates from overburden drilling at a surface coal mine and the transport of this dust to downwind locations. The emission rates were estimated by using multiple gravimetric dust samplers mounted on a cross-shaped tripod located immediately downwind of the drill. The transport of this dust was measured at more distant downwind locations by a combination of respirable gravimetric sampling and integrated bag sampling of sulfur hexafluoride (SF6), which was used as a tracer gas. Two modes of sampling were used: (1) At five sampling locations arranged in a semicircle around the drill. The radius of this arc ranged from 15.85 m (52 ft) to 71.32 m (234 ft). (2) In-line sampling at downwind locations with samplers located at intervals of either 10.67 m (35 ft) or 15.24 m (50 ft) for a total distance of 76.20 m (250 ft). Samples were taken 1 .22 m to 1.52 m (4 to 5 ft) above ground level. Test results for the semicircular test arrangements showed that at any downwind location, the maximum contribution of respirable dust due specifically to the drilling operation was 42%; the average for eight tests was 13.6%. In general, there was no correlation between the downwind distance of this maximum contribution and the maximum contribution itself because of changing wind direction. Test results for the in-line arrangements indicated that the transport of the dust from the drilling operation usually decreases rapidly with distance and that, even though the drill dust may produce significant health hazards for the drill operator and drill helper (or other personnel in the immediate vicinity), the exposure of downwind personnel to drill-generated dust may not be a significant problem.

Jan 1, 1987

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990

By James C. Puckett

The mining industry finds itself in the middle, between the need to increase production of our energy resources and the necessity of minimizing the environmental impact. Using the recent past as a guide, the mine planning engineer's function will continue to increase as further coal quality constraints are made upon the production staff. The engineer will need to make use of all available tools in order to provide timely answers to the complex "what if" questions that arise. This need to consider many alternatives is bringing about a rapidly increasing acceptance and utilization of the computer. In the areas of data handling, mineralization modeling, and production simulation, the computer is an effective tool for the mine planning engineer. Described herein is a coal data storage and analysis system developed to provide timely answers to the "what if" questions for an operating strip coal mine in Montana. The characteristics of a computerized coal data base and coal quality planning system are outlined in this chapter. The system has been developed for use at a particular coal mine; however, it has applicability to coal mines in general. Fig. 1 is a flow chart showing the functional relationships of the system. There are three main file types: the drill-hole data base, the boundary file, and the zone file. The purposes for which each file is organized are illustrated on the flow chart.

Jan 1, 1979

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992