Search Documents

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By K. Oraee

Excessive emissions of methane from the coal seams can have a serious adverse effect on both safety and productivity of longwall coal faces. Mechanization of coal faces has increased production possibilities to the extent that normal ventilation systems may not be able to ventilate coal face areas in order to lower methane content in the air to within legal limits. Production increases may therefore be prohibited for this reason, especially in gassy seams. Methane drainage from the coal seam by means of long holes and before production starts can act as a useful remedial action. In this paper a two dimensional mathematical model has been produced. The model that is based on finite elements, simulates a methane drainage system where the resultant risk is linked to the coefficient of diffusion, coal permeability, holes pattern and the duration for which the seam is subject to drainage. It is concluded that methane drainage of this type can assist in achieving production increases in many coals seems, especially where high gas content is a virtue of the seam.

Jan 1, 2010

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

By Wi11iam M. Leaders

Uranium Recovery Corporation was incorporated in the State of Florida in 1968 for the sole purpose of developing a method to economically recover uranium from Florida phosphoric acid. The preliminary laboratory work culminated in the demonstration of the process to United Nuclear Corporation in the spring of 1971. This was quickly followed by a pilot plant program to identify any unusual problems such as those arising from the day-to-day variation which occurs in a fertilizer phosphoric acid plant production system. After two years of pilot plant operation, United Nuclear Corporation purchased controlling interest in Uranium Recovery Corporation and committed several million dollars to the design and construction of the first commercial plant for this purpose in the State of Florida, or anywhere else in the United States, for that matter. After many start-up problems were resolved at the production plant located at the W. R. Grace fertilizer complex near Bartow, sustained production began March, 1971, and has continued to date. We still have some problems to solve but are currently producing sufficient uranium to make shipments to the UF6 converters for preparation of Florida uranium for use in nuclear power plant fuel materials.

Jan 1, 1978

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By S. Bhagwat

Coals capable of emitting 2 lbs SO2/106 Btu heat input must be defined as high sulfur coals. This is because electric utility plants built after 1971 may not emit more than 1.2 lbs SO2, and those built before 1971, and regulated under the State Implementation Plans (SIP), may exceed the 2 lbs S0 limit only under closely defined restrictions concerning ambient air quality and prevention of air quality deterioration. Coals produced in Kentucky, Illinois, West Virginia, Ohio, Pennsylvania, and Indiana account for 77% of SO2 pollution potential and are, therefore, the subject of this investigation. These coals have suffered market share losses in the 10 years from 1974 through 1984. This is due to their sulfur content as well as their lack of price competitiveness with low sulfur western and imported coals. Kentucky and West Virginia have been able to increase their compliance quality coal production substantially, but other states have largely been unable to do so because of nonavailability of low sulfur coal deposits. Assuming that the current relative productivity and cost competitiveness of coal producing states will not change significantly by 1994, this paper makes two projections of coal production in the selected states. In scenario I, the current clean air regulations are assumed to apply until 1994, and coal production in the selected states is projected to in¬crease by about 6% in 1994 compared to 1984. In scenario II, it is assumed that acid rain legislation will be implemented, which will adversely affect the markets for high sulfur coals. Coal production in the selected states under this scenario is projected to decline about 10% between 1984 and 1994, jeopardizing up to 13,000 mining jobs. The author concludes that better coal quality and greater cost competitiveness are both essential to stem the market losses and to regain strength.

Jan 1, 1988

By B. Schimm

Mining of material without blasting and / or selectively becomes more and more important for high quality ROM-products. Surface Miners have been developed especially for this purpose. The cutting technology of these machines has been improved, so that harder material as well as wet and sticky materials can be cut with better results now. Especially the cutting drum design and more precise drum manufacturing process now allow production and equal tool wear over a long period. The better knowledge of rock parameters influencing the cuttability and cutting results allow higher production, less cutting tool wear and therefore reduced production costs.

Jan 1, 1999

By Javad Sattarvand, Frimpong Kwaku Asare

The safe evacuation of miners during an emergency in the shortest amount of time is one of the most essential features of a mining operation. Despite advancements in mine evacuation research, the usage of mine vehicles during evacuation has not been considered. The majority of recent studies have been done on miners’ evacuation on foot. Mathematical formulations including Minimum Cost Network Flow (MCNF) models, Dijkstra's algorithm, Floyd-Warshall algorithm, and Ant Colony Optimization models have been used to solve mine evacuation problems. These models, which concentrate on determining the shortest escape routes during the evacuation, have been found to be computationally expensive and may not offer the best solutions in some cases. The goal of this paper is to incorporate light vehicles in the evacuation process using a mixed-integer programming approach. The methodology aims to minimize the total time required to evacuate the mine, ensuring minimal exposure of the miners to the adverse conditions that triggered the evacuation.

Jun 25, 2023

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By C. E. Jordan

The Bureau of Mines conducted research to determine the effect of fine bubbles on the flotation of fine-sized particles (minus 20-um size). Turbulent flow collision models for fine particles and fine bubbles were reviewed. Velocity distributions within the flotation cell along with measured bubble and particle size distributions were considered in the models to predict the flotation response. The models were corroborated with laboratory fine-bubble flotation tests to verify the expected increase in flotation efficiency.

Jan 1, 1988

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By John C. LaScola, Gerald L. Finfinger, Michael A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is the method of choice used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970’s, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the U.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6560 Mm3/d (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2832 m3/d (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm3/d (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1991

By G. Perkins

The development of the mineral industry of Jamaica has been guided by an unwritten policy which has nevertheless been reflected in various pieces of mining legislation and by case-by-case approvals of incentive packages for non-bauxite minerals. An effort has now been made to bring together in one minerals policy document, all the policy elements that have guided our laws and actions thus far and to upgrade the final version to meet the challenges of the next century. In this regard, industrial minerals will be placed on a more equal footing with bauxite, especially in terms of investment incentives.

Jan 1, 1998

By Larry J. Hughes

Ground-based electrical geophysical techniques have be valuable for three indirect exploration strategies: "tracer" sulfide mineralization, 2) mapping structure with or controlling mineralization, and 3) mapping proven to 1) mapping? associated alteration zones. When sulfide mineralization is associated with gold, it often can be mapped using induced polarization (IP). This technique can detect pyrite in amounts as small as 0.2% by volume, and in some cases can distinguish pyrite from anomalies due to graphite and clays. A case history illustrates mapping sulfides in a shear zone. Structure and alteration mapping are often the domain of controlled source audio-frequency magnetotellurics (CSAMT) due to the superior lateral resolution and depth penetration of this technique. Typical CSAMT targets include silicified sediments and volcanics, faults, brecciated zones, argillic alteration, clay and graphite horizons, and certain lithologies. Examples of mapping silicification and mapping epithermal alteration are presented in CSAMT case histories over Cannon mine in Washington and Hishikari mine in southern Japan. In our experience, four things are needed to use geophysics effectively in precious metals exploration. First, the explorationist must correctly identify the exploration stage at which the geophysics is most useful. Second, the explorationist must clearly define the types of "tracer" mineralization, host geology, or alteration which need to be defined by the geophysics. Third, the right electrical technique needs to be applied to the problem to provide the best chance of success. Fourth, the explorationist must be willing to commit adequate finances to do the geophysics properly. With careful adherence to these principles, geophysics can greatly enhance exploration success while reducing the total cost of exploration.

Jan 1, 1989

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul road conditions can positively impact mine operations resulting in increased safety, productivity gains, increased tire life, and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain mine, monthly site severity studies, ad hoc inspections by frontline supervisors, or operator feedback reporting is used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage, and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

Sep 15, 2020

By Douglas Owen

Two case studies describe the introduction of technology new to an organisation. The lessons learnt from these Case studies contribute to Our general understanding of the management of technological change.

Jan 1, 1989

By Gerd Oberheuser, Hans Kellerwessel

Comminution with high compression roller mills finds rising interst in ore and minerals industry. Energy saving and upgrading of existing grinding facilities is one of the main reasons. Beside these possibilities other positive effects on the downstream units operations require also intense testwork. Basic interdependencies of the operational parameters gained at the testwork and their influence on the upscaling procedure are described.

Jan 1, 1995

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By T. M. Sukel

Engelhard Corporation is one of the leading producers of kaolin based products in the world, having acquired the assets of Freeport Kaolin company in 1985. Much of the production technology used in the kaolin industry was pioneered by Engelhard and Freeport, including Ultraflotation for improving product brightness, delamination to produce kaolin platelet products, calcination to produce ANSILEX® high opacity titanium dioxide pigment extender and pipeline slurry operations to economically transport kaolin from the mine to beneficiation facilities. Engelhard traces its roots back to 1870 when the Edgar family discovered kaolin behind their property in Bonhamtown, New Jersey. Today the company produces the broadest line of premium coating pigments with extensive sales throughout the world. The international scope of the company's business has led Engelhard to evaluate kaolin deposits throughout the world as possible grass roots production sites. Most kaolin products are used in the paper industry -- the largest volume end-user 80% of the total market -- as filler and coating pigments. Lower volume specialized applications include fillers and reinforcements for plastics and TiO2 extender pigments for paints and coatings.

Jan 1, 1987