Search Documents

By M. S. Celik, G. Onal, S. Atak, A. A. Abramov

An oolitic phosphate ore composed of phosphate (mainly francolite) and carbonates as gangue has been tested for the suitability of the reverse flotation process. The samples were first ground autogeneously followed by the reverse flotation process. While the carbonates were floated by sodium oleate the phosphate was depressed by phosphoric acid. The effect of particle size, reagents type and concentration on flotation recoveries have been investigated to determine the optimum conditions. By this process, a run-of-mine ore containing 16.72 % P205 was upgraded to 28.00% P205 with a recovery of 77.0% The mechanism of optimum flotation with phosphoric acid observed at pH 6.3 is explained based on a relationship involving surface potentials and the ratio of required collector concentrations for the respective minerals.

Jan 1, 1993

By Kurt Zeidler, Vojtech Gall

London Underground Limited are currently constructing an extension of the Jubilee Line. The approximately 16-km long Jubilee Line Extension Project connects the existing Green Park Underground Station with the Canary Wharf area and Greenwich. Being a part of the project, the London Bridge Station (Contract 104) was built using a combination of the New Austrian Tunneling Method (NATM) with Compensation Grouting. NATM was successfully applied in softground and urban areas under restrictive requirements regarding settlement limitation. Information on the flexibility of the method and the influence of Compensation Grouting on ground and tunnels are given.

Jan 1, 1997

By J. G. Groppo, B. K. Parekh

Column flotation testing was conducted on the flotation feed slurry obtained from a preparation plant located in the Southern Illinois coal basin. The column flotation tests were conducted using three different bubble generating devices: a static sparger, a gas saver and a foam jet. Each of these devices was tested with three different types of frother and various column operating variables to provide maximum combustible recovery, minimum product ash and maximum pyrite rejection. The results show that column flotation provided improved flotation performance, in terms of combustible recovery as well as ash and pyrite rejection, for each of the bubble generating devices. However, the effectiveness of each bubble generating device was dependent on the type of frother used. Alcohol frothers were most effective for use with the static sparger, somewhat less effective for the foam jet and ineffective for the gas saver. Glycol frothers were effective for all three bubble generating systems, providing high combustible recovery (>90%); low clean-coal ash (4-6% ash) and high pyrite rejection (70-80%).

Jan 1, 1994

By Edward S. Plotkin

The tunneling construction industry faces a new challenge in endeavoring to comply with the multitude of regulations and standards of the Occupational Safety and Health Administration and to work following accepted and experienced tunneling practices. Tunnel inspections appear to be gaining in priority. The national OSHA inspection activities reported for the year 1976 in the construction industry are as follows: 989 Inspections 45 As result of Accidents 186 As result of Complaints 605 General 153 Follow Up 34% Were found to be in compliance 714 Citations were Issued 1,825 Violations were found (201 of which were serious; 1573 were non-serious; 51 were imminent danger. There were no recorded failures to abate a violation in our industry.) The five general priorities by which a company would be scheduled for an inspection in descending order are: imminent danger situations, reports of fatal accidents or catastrophies, inspections in response to valid employee C( taints, inspections of work places covered by National Emphasis Program NEP, (OSHA's NEP has been designed to impact on any industry having a very high injury or illness rate) and finally random inspections of work places covered by OSHA. The following criteria in selecting companies for random inspections is used by OSHA.

Jan 1, 1979

By Liu Hongkang, M. J. Virnig, Yang Xianwan, Zhu Yun

A new technology for recovery of gold from loaded carbon developed by Kunming Institute of Technology is introduced. The principle, production practice and results are described.

Jan 1, 1993

By A. M. Stone

INTRODUCTION In ore beneficiation one of the simplest methods of mineral concentration is hand picking to remove either the ore or the waste material from a moving table or conveyor belt. Ore Sorting Equipment may be defined as equipment for mechanized picking. This type of equipment has been used successfully over the past thirty years or so to beneficiate ores of various types in particle mesh sizes between 1mm and 200mm.. at throughputs of up to 150 tonnes per hour. In general for ore sorting to be a consideration the ore and the waste material must be well liberated in the feed to the sorter (that is into practically discrete particles of ore and waste). The larger the liberation size the more likely sorting is to be cost effective. Correct selection of ore sorting equipment is most important and often special machine features are developed for an individual application. Sorter performance can be best determined by extensive testwork of representative ore at design tonnage on prototype or preferably on production model sorting machines. ADVANTAGES OF SORTING ORE The four main advantages of sorting ore are: Reduced milling cost. Reduced processing cost. Higher overall recovery. Reduced transportation costs. Reduced Milling Cost With sorters installed the milling plant following the sorter is generally smaller and hence less costly to install and operate as it only has to handle the sorter product. However this benefit is somewhat offset by the increased cost of the screening and washing plant prior to the sorter and the cost of the sorting plant itself. Reduced Processing Cost As there is less material of higher grade presented to the concentrating plant following the sorter, this plant will generally be smaller and less costly to construct and operate than a plant treating the total quantity of material. Higher Overall Recovery The economic recovery is often misunderstood by plant operators when evaluating the advantages of sorters

Jan 1, 1986

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operating point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique features of the Lone Tree sulfide deposit and its amenability to low-temperature oxidation. Problems encountered during pilot plant operation and their solutions are discussed.

Jan 1, 1995

By T. E. Breaux

Repair of large rotating apparatus such as ball mills is uncommon but under certain circumstances is achievable. This paper describes the successful repair of trunion on a 14 foot diameter by 20 foot long ball mill. Diagrams of the repair are included for visual perspective and non-destructive test procedures are outlined.

Jan 1, 1988

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By Felicia F. Peng, Lili Li

The dispersion model of nonideal flow was applied to describe the hydrodynamic state within the flotation column. Residence time distribution (RTD) data of a laboratory flotation column were measured to determine the parameters of the model. The effects of operating variables and column geometry on the Peclet number which reflects the extent of axial dispersion were investigated and a semi-empirical expression of Pe was formulated. The dispersion model was validated for the column flotation of ultrafines coal. Under the conditions of sufficient aeration rate and frother addition, a good agreement between the measured recoveries and predicted data was obtained. The dispersion model with first-order flotation rate process of the flotation column developed in this study is useful in predicting the collection zone recovery of fine coal, and for the flotation column scale-up.

Jan 1, 1995

The classical slope analysis and a statistical technique were used in order to determine the iron complexes formed in the organic phase during the extraction of Fe(III) from Fe-Ni-Co sulfate solutions with Di-(2-ethylhexyl) phosphoric acid (D2EHPA) in kerosene. Equilibrium constants for the extraction based on these complexes were also calculated. The complexes determined were of the general form (Fe(OH)3-nRn?sHR)x' where n varied between 1 and 2.5 and s between 0 and 3, and both were found to be decreasing as the iron loading in the organic phase increased. Values of 1,2 and 3 were generally found for x, indicating that the complexes were monomers, dimers and trimers.

Jan 1, 1988

By J. E. Brownhill

After being closed for three years, Specialty Minerals Inc.'s Port Inland limestone facility reopened in the spring of 1992 as a commercial limestone producer. In 1990, Specialty Minerals, a division of Pfizer Inc., bought Port Inland's reserves and equipment from Inland Steel because of the strategic value of the limestone for the production of precipitated calcium carbonate (PCC). Specialty Minerals' project team faced many challenges in reconstructing the Port Inland facility. Many traditions and norms had to be overturned to achieve the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. Port Inland's history Inland Steel built Port Inland in 1930. It was operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. The facility is located in the Upper Pen¬insula of Michigan on the north edge of Lake Michigan. Operations consist of a deep water port facility with crushing, screening and stockpile storage for 453 kt (500,000 st) of finished product at the port. Ninety-nine percent of the stone is shipped by lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical dolomite and limestone are produced on site.

Jan 1, 1994

By Jasinder S. Jaspal

The United States has very large coal reserves in seams that are less than 1065 mm (42 in.) thick. These reserves are often not mined because of the difficulty of working in low heights and, in most cases, the seams are beyond the technical or economical limits. It is estimated that the remaining reserves in 355 to 710 mm (14 to 28 in.) thick seams that are not faulted or intruded, dip less than 15° and under a cover of 610 m (2000 ft) or less are nearly 910 Gt (1 trillion st). This is a very large percentage of coal reserves in the United States (Unrug, 1985; DuCarme et al., 1990). The US Bureau of Mines is attempting to develop new techniques for mining 150 to 1065 mm (6 to 42 in.) thick coal seams. Research has focused on existing thin seam mining techniques, testing of small- and full-scale physical models of the Bureau's slot mining concept and computer modeling of the full-scale process. In 1986, only 21 % of the total US coal production came from -1065 mm (-42 in.) thick seams. Of that, 355 to 710 mm (14 to 28 in.) thick seams share of production was minimal, probably 5% or less (Mayercheck et al., 1990). This shows that the thin seams, particularly the seams 355 to 710 mm (14 to 28 in.) thick, have not been mined to the extent of the available reserves. Thin seam coal, generally, is of premium quality. As thicker seams are depleted, the mining of thin seams could become more important. Thus, there is a need to develop technology to mine these seams (J. Farinelli et al., 1987). A successfully applied technology could change reserve categorization. In the Appalachian Plateau there are 417 Gt (460 billion st) in 355 to 1065 mm (14 to 42 in.) seams. This represents nearly 9.2% of the US remaining reserves (Unrug, 1985). At depths of 152 m (500 ft) or less, the Appalachian Plateau has about 214 Gt (236 billion st) of reserves in 355 to 1065 mm (14 to 42 in.) thick seams. Other mining areas also have substantial coal reserves in this seam thickness category. Those, however, are not as attractive for mining as the Appalachian Plateau. In the past, most of the reserves of the Appalachian Plateau region were partially worked by contour and highwall auger mining. It is estimated that these mining systems had left some 40,230 km (25,000 miles) (Readers Digest, 1987) of unreclaimed highwalls. The Bureau recognized this situation. In FY1987, the agency initiated a research project to develop anew technology for mining thin seams of the Appalachian Plateau.

Jan 1, 1992

By R. Buchan

A number of mineral processing techniques have been adopted for the separation of the plastics making up a typical beverage bottle, and a complete flowsheet developed. Thus, size reduction, heavy media separation and flotation were used to separate PE, PVC and PET from their mixtures with cellulose fibers and aluminum, which makes up the cap of such bottles. It is shown that while heavy media separation allows the separation of a PVC/PET mixture from the solid waste, froth flotation can be readily used to separate PVC and PET from a mixture of the two. For this purpose, the differential action of an alkaline aqueous solution (PH=II) which contains methanol and MIBC as surface tension control agents has been found to be a suitable flotation medium. This paper reports some aspects of the flotation flowsheet developed for the separation of plastics from municipal solid waste mixtures and PVC from PET.

Jan 1, 1995

By Richard R. Klimpel

This paper discusses the use of froth flotation as a means of removing metal containing species from a variety of feed streams that generally fall into the classification of waste streams. The variability in solid composition, degree of oxidation, water chemistry, and levels of organic/inorganic contaminants associated with waste streams implies that the collector chemicals used in any flotation process must be much more selective than typically required in normal mineral ore flotation systems. Several examples of such work currently underway will be illustrated showing the potential of flotation to upgrade metal-containing waste streams.

Jan 1, 1992

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By H. Köse, C. Tatar, C. Helvaci, F. Simsir

The Çayirhan coal basin is located 124 km (77 miles) west of Ankara,Turkey. With approximately 520 Mt (570 million st) of lignite reserves, the Neogene Çayirhan basin is one of the important coal districts of the central Anatolia region. The Çoraklar formation consists of crossbedded sandstone, channel fill conglomerates, mudstones, carbonaceous shales and volcanoclastic pebblestones, which are fluvial in origin. The lower and upper lignite seams occur, respectively, in the lower and the uppermost parts of the Çoraklar formation. The lignite deposits are in the Çayirhan and Koyunagili portions of the Beypazari Neogene basin. The Çayirhan coalfield consists of lower and upper lignite seams. The lower lignite seam does not outcrop at the surface. Its lateral discontinuity and relatively low sulfur content, plus sedimentologic and stratigraphic features of the associated sediments, indicate a fluvial origin. Thus, the lateral spreading and geometry of the lower lignite deposits were controlled by the channel, flood plain and well drained marshes of a fluvial system. The mining method employed at Çayirhan is the fullymechanized, retreat, working longwall with caving system. Due to ventilation, haulage and tectonic conditions, panel lengths from 0.6 to 1.7km (0.4 to 1.1 miles) are chosen, and 220-m (720ft) face lengths are used. The annual coal production is 2.2 Mt (2.4 million st).

Jan 1, 1994

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By Oscar Letelier Gonzalez

The goal of mine planning is to determine "the best" strategy to exploit an ore deposit during its workable life. Such strategy must be consistent with the objectives of the company and must be subject to the contraints imposed by economical, physical and geological conditions. Mine planning process may be broken down into three categories, according to the planning horizon: Long range, Short range and Operational. The shorter the scope of planning, the higher the level of details and the lower the degree of freedom associated to each plan. A long range plan defines the economic limit of mining at the mining life end of the deposit; it also can be used as an aid in the evaluation of the economical potential of a mineral deposit and as a guide for short range plans.

Jan 1, 1979