Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By Victor J. Scaravilli, C. Richard Linamen

This paper presents a case history of Southwest Interceptor Contract No. 1, Cleveland, Ohio. It details some of the problems and solutions of handling and erecting precast concrete segments in a small bore soft ground tunnel. It also reviews how specific interpretations of contract requirements and contract administration effect production, performance and productivity.

Jan 1, 1987

By R. K. Mehta, C. W. Schultz, R. R. Mallepali

Stirred ball mill feeds used for ultrafine grinding applications require a fine size separation step to avoid overgrinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide ore using a 460-mesh (30-µm) Derrick vibrating screen. The selectivity curves generated from the experimental data show increasing selectivity with larger size for the oil shale but not for the sulfide ore. These unusual selectivity curves are similar to the mechanical air separator, fishhook selectivity curves described by Luckie and Austin. A two-stage, in series, classification model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when a heterogeneous, multicomponent sulfide ore undergoes size separation.

Jan 1, 1994

By W. Bassow

In June 1972, when the United Nations convened its historic Conference on the Human Environment, only 24 countries had established government agencies with environmental responsibilities. Of these, 11 were in the industrialized world, 13 in the Third World. By 1985, the number had dramatically surged to a world-wide total of 145, with the greatest growth among the developing countries to 110, an increase of almost 1000%.

Jan 1, 1988

By Deepak Malhotra

The economic viability of mineral companies not only depends on maximizing mineral recoveries but also on their ability to do so at minimum cost. Increasing pressure to cut costs has resulted In reduced staff, thereby decreasing the capabilities of routine metallurgical audits. This paper reviews a systematic approach to plant auditing which has been used successfully at several operations. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1991

By P. A. Anderson

Innovative solution management is being used at Coeur-Rochester, Inc. to increase bullion production and decrease overall costs. New operating programs call for reduced solution application rates to the heap to increase pregnant stream values at a lower and less costly plant flowrate because silver and gold extractions are equal regardless of leach solution application rate. Solar heating is used in the summer months to increase the core temperature of the heap for use in the winter months thus increasing silver extraction rate. This paper outlines the programs now in effect and the savings incurred because of them.

Jan 1, 1989

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

Accidents that resulted in 16 deaths in three West Virginia coal mines, two in Kentucky and one in Utah have government and industry re-evaluating current safety regulations. Even though U.S. mines continue to improve on their safety records, the deaths reminded the industry and state and federal agencies that mining remains a dangerous business. Even so, data from the U.S. Mine Safety and Health Administration (MSHA) show that new technologies and a highly trained workforce has allowed the nation’s coal mines to increase production while providing safer workplaces. Since 1970, coal production at U.S. mines has increased by about 83 percent. During the same period, fatal injuries have fallen by 92 percent. And more than half of the U.S. coal mines operate each year without a lost-time injury. In 2005, there were 22 deaths in U.S. mines, a record low.

Jan 1, 2006

By M. S. Kabibwa, E. K. C. Chanda

In planning for the future, Nkana Division deepened the Mindola sub-vertical shaft which was commissioned in 1994 in order to access the 30 Mt of ore between 1274 and 1570 m levels. The Nkana Synclinorium which is estimated to contain 250 Mt of ore is being accessed from the vicinity of Central Shaft. These areas are being planned with the intention of maximizing the use of computers in geological modelling and mine design so as to overcome the inadequacies of manual planning techniques. As a result, there is an increased demand for quality output from the computerized mine planning system the division has been developing over the last few years. A new workstation comprising the Hewlett Packard HP 71 51100 MHz and a CRX graphics monitor was acquired in 1995 together with the LYNX (version 3.09 and version 4.0) Mine Modelling System. Currently the workstation is being used for geological modelling and mine design for the Zerofold at Central Shaft and the Mindola mining at depth project. AutoCAD and Mine Works Planner have been added to the sys- tem configuration. Mine Works Planner is likely to replace Lo- tus123 for mine scheduling tasks. Computer applications in the area of mine planning at Nkana has led to considerable time savings and improved efficiency in areas formerly performed manually and has allowed speedy processing of data that would otherwise have proved too time consuming. Nevertheless, a lot of work still needs to be done in the areas of geostatistics, stope design and financial modelling of mining options. For the foreseeable future computer based planning will operate parallel to manual methods until such a time as sufficient personnel are proficient in the use of computer systems. This paper describes the program of computerization at Nkana Division, reviews current applications and the benefits and experience gained and discusses the promise of current and future developments.

Jan 1, 1996

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role and the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By Farlow C. Davis

Magma Copper Company, San Manuel Division, is a wholly owned subsidiary of the Newmont Mining Corporation and located at San Manuel, Arizona. The ore body is a dessiminated porphry copper deposit in quartz monzonite. The primary copper mineral is chalcopyrite with minor amounts of chalcocite, bornite, and covellite. The molybdenite occurs mainly on fracture faces or else associated with quartz veinlets. Pyrite is the major sulphide mineral in gangue. The feed to the concentrator from the underground mine is approximately 0.720 percent copper and 0.029 percent molybdenite. The concentrator has a design capacity of 62,000 tons of ore daily. After a standard ore treatment circuit consisting of grinding, rougher flotation, regrinding, and cleaning, a bulk concentrate is produced which contains 27 to 29 percent copper and 1.0 to 1.2 percent molybdenite. This concentrate is pumped to the molybdenite plant feed thickener.

Jan 1, 1977

By Gordon S. Thomas

The problem of how best to exploit a reserve has vexed mine planners and design engineers since mining began. The cyclic nature of the mine design-scheduling problem, combined with the lack of good mathematical tools for tackling it, have ensured that it has been, and will continue to be, a major challenge for operations researchers working in mining. This paper reviews the current state of the art in pit optimisation and scheduling algorithms. Starting from the inception of the first block models in the late 1950's, it progresses through the developments and applications of the Moving Cone algorithm, the Lerchs Grossmann 3D Graph Theory algorithm and some of the heuristics, to the new artificial intelligence techniques that are being applied today. Along the way, it discusses the limitations of the various approaches and lays the foundations for the research that is currently being undertaken by CSIRO and others in the field of mine production scheduling and control.

Jan 1, 1996

By L. A. Hansen, D. L. Buffington, G. H. Beckwith

This paper reviews geotechnical engineering considerations in heap leach pad design, discusses design philosophy and provides design procedures. A brief discussion of surface water hydrology ground- water protection and other design considerations are also presented. Special emphasis is placed on projects in the arid and semiarid regions of the Western United States where annual evaporation exceeds rainfall, and where good foundation conditions are usually present.

Jan 1, 1987

By R. J. Gochin, M. A. Diaz, M. L. Court

Single impact breakage tests have been carried out on samples of alumina in carefully controlled atmospheres consisting solely of nitrogen gas and water vapour. The results indicate a statistically significant increase in the surface area of the progeny particles as relative humidity rose to 50%. The majority of this increase was found to occur under conditions when adsorption was a monolayer or less. The results are consistent with the theory of surfactant-induced strength reduction of materials proposed by Rehbinder and Westwood. There are important implications where single impact tests are used as part of a design methodology for comminution machines. In most procedures relative humidity has not been a controlled variable.

Jan 1, 1995

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By K. E. Brown, T. D. Murphy

At Monterey Coal's No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By B. M. Davis, J. Wilkins

The method of conditional simulation is easily implemented on the personal computer when the LU decomposition algorithm of Davis (1987) is employed. This algorithm is fairly compact, yet can generate moderate-sized simulations in a few minutes on a 80286 or 80386-based personal computer. The application of conditional simulation presented here is to generate possible ore inventories from a limited amount of exploration sampling. The simulations can then he examined to decide if the potential inventories are sufficiently attractive to proceed with further exploration. An example showing one application of this approach is presented.

Jan 1, 1992

By Robert Irvine

Exploration activity for diamonds in Canada has recently experienced a dramatic increase. Disclosure of a diamond discovery exhibiting features of a potentially economic deposit contained in a kimberlite pipe in the Lac de Gras area of Canada's Northwest Territories has sparked substantial interest in-Canada and abroad and has triggered the largest staking rush in terms of area in the history of Canadian exploration. In this paper, we report on the nature and extent of current exploration activity in Canada for diamonds (with special attention to Arctic regions), the results of this activity to date, and the context in terms of current world markets for diamonds.

Jan 1, 1995

By Nathaniel Arbiter, Brij M. Moudgil

Separating oil shale from waste material or into high- and low-grade fractions can have a major economic influence on the surface retorting process. Different shale rock components vary significantly in physical and surface chemical properties, such as specific gravity, color, and water wettability. Various techniques that use the differences in one or more of these properties have been proposed to preconcentrate oil shale before retorting. This article discusses some proposed techniques, such as gravity separation, sorting, and froth flotation. Retorting oil shale is the most common method for recovering oil from the rock. This process is accomplished either underground (in situ) or above ground (ex-situ or surface retorting). Both techniques have serious limitations, such as low recoveries in the underground method and the ability to process rich shales only in the above ground retorting method. Also, environmental problems are associated with both techniques. Some of these limitations could be overcome if feed to the retorts is of consistent grade. This could be achieved by selecting appropriate sites for in situ retorting and selective mining for surface oil shale retorting. Both of these, however, would have a serious economic impact on shale oil recovery. Obviously, little control can be exercised over preparing feed material in the in situ retorting process, but beneficiation of oil shale could definitely be advantageous in surface retorting, and should have positive influence on the overall economics of recovering oil from the shales. For example, preconcentration of mined shale could result not only in reduced costs for materials handling, but also in waste disposal costs, since waste characteristics before and after the retorting process are significantly different. Upgrading the oil shale might also allow substitution of alternate technology for retorting as well as extend the process to recover oil from marginal deposits. Also, the separated material may become a potential source for recovering other values from shale deposits. Overall, the incentives for preconcentration are to reduce costs and improve thermal efficiency of the recovery process. Oil Shale Properties Important to Preconcentration Oil shale is a carbonaceous rock assaying 5-30% organic material (kerogen) and 70-95% ash-forming minerals. Kerogen is soft, nonbrit¬tle or semi-brittle material, and generally forms a matrix between irregularly distributed mineral grains. Inorganic mineral mat¬ter-quartz, feldspar, dolomite, kaolinite, dawsonite, and nahco-

Jan 9, 1982