Search Documents

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By J. A. Frew, R. M. Glen

Recovery of galena and sphalerite from fine grained lead-zinc ores by flotation normally requires re-grinding to achieve economic recoveries at acceptable concentrate grades. Re-grinding aims to reduce the coarse valuable mineral particles to a size where they float more readily and to liberate the composite valuable particles so that the gangue in these composites does not dilute the concentrate. Besides changing particle size and liberation, re-grinding changes the surfaces of the minerals and thus may alter the rate that mineral particles of a given size and liberation float. A method was developed to apportion the total change in recovery after re-grinding between changes in size and liberation and changes in flotation rates. The flotation behaviour of minerals, before and after re-grinding, was measured by floating samples of plant streams under controlled conditions in a laboratory cell. Results from several industrial lead-zinc circuits indicated that the change in behaviour observed fell into three different categories. It is concluded that the method will indicate whether the focus for optimization of existing plant should be on comminution or flotation, and it will help determine the path for laboratory testing in designing new regrind circuits.

Jan 1, 1995

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent Bureau of Mines research on scrubbers is reviewed, with emphasis on the following areas: * Development of a new type of water-powered scrubber which can be retrofitted to existing miners. * Comparison of scrubber effectiveness with blowing and exhaust line ventilation. * Improving the quartz dust collection of flooded-bed' panels.

Jan 1, 1989

By X. Wu, M. Karfakis, E. Topuz

The generalized ventilation network problems encompassing both natural and controlled splitting networks, is formulated using a nonlinear nonconvex programming model, which has not yet been solved satisfactorily. This paper presents a methodology which can deal with the problem. The proposed methodology converts the nonlinear problem into a linear problem, by using special ordered sets of variables, and optimizes it by a modified branch and bound technique. The global optimality of the methodology and its applicability to different cases are investigated

Jan 1, 1991

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981

By K. P. Madhusudhanan, R. K. Bhatia, K. S. Narasimhan, R. N. Singh

A typical case study of a coal washery of capacity 500 t/h raw coal input has been presented and discussed with particular reference to the techno-economics for flotation column vis-a-vis the conventional flotation cells, keeping parameters like input capacity and product ash same. The results presented indicate that substitution of flotation cells by columns in a coal washery results in advantages of increased fine coal recovery, better quality of concentrates, lower capital and production costs etc.,. The effect of increasing the specific capacity of the column by design modifications on the cost benefit is also analysed.

Jan 1, 1988

By V. Karra

Based on extensive investigations on the effect of design variables on process performance, during 1982-85, Nordberg developed a 1000 hp cone crusher, with the objective of boosting crushing productivity in existing plants. The 2390 fits on the same foundation as the 7' SHD Symons cone, but is designed to give two times the capacity of the 7'. The economies of scale involved give the customer substantial cost savings. In this paper process performance of the Nordberg 2390 relative to the 7' SHD Symons cone, while crushing the same ore, will be presented. Also, implications of such a crusher scale-up to associated cost savings will be addressed.

Jan 1, 1988

By Jeffrey D. Swanson, Martin L. Smith

Smelterville Flats in Idaho's Silver Valley has been designated as a Superfund site due to metals contamination resulting from the use of the South Fork of the Coeur d'Alene river as a tailings impoundment earlier in this century. Tailings average in excess of 4% lead and zinc. Selective mining of highly contaminated zones is being studied as one of several possible remediation strategies. The first step towards remediation is the examination of the stratigraphic, geochemical and spatial characteristics of the site. These characteristics are related to appropriate sampling protocols and exploratory sample grid design. Special problems involved in the geostatistical analysis of tailings are emphasized.

Jan 1, 1992

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Robert A. Haney, Richard T. Stoltz

In July, 1988, the Mine Safety and Health Administration (MSHA) Advisory Committee on Standards and Regulations for Diesel-Powered Equipment in Underground Coal Mines recommended that the Secretary of Labor set in motion a mechanism whereby a diesel particulate standard can be set. Prerequisite to establishing a standard would be the development and evaluation of instrumentation to measure diesel particulate. In response, the Mine Safety and Health Administration, Dust Division, has been evaluating instrumentation that can be used to determine diesel particulate levels in underground mines. This instrumentation employs the principle of impaction to separate particles by size, thereby, separating the diesel and nondiesel particulate. Separation of the particulate by size was chosen because diesel particulate is generally less than 1.0 micrometer in size. No other methods have been developed to successfully distinguish between the coal and diesel particulate. MSHA developed an impactor that is inexpensive and compatible with existing pumps and filter holders. The instrumentation evaluation has primarily focused on the repeatability and performance of several personal dust samplers. The samplers tested include the Sierra-Andersen Model 298 personal impactor and MSHA developed personal impactor. The MSHA impactor is inexpensive and compatible with the existing pumps and filter holders. In addition to evaluating the precision and performance of these instruments, tests have been conducted to determine background levels of submicron particulate in nondieselized coal mines and to measure the submicron particulate content in dieselized coal mines. Tests were conducted in coal mines where diesel equipment was used only in outby areas and also in coal mines where diesel equipment was used for face haulage. This paper describes the results of the tests and provides a description of the instrument at ion used to conduct the tests.

Jan 1, 1989

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

The Witwatersrand reefs provide excellent examples of chemical and structural control on gold distribution. All mined gold appears to coma from a carbon -gold association and/or Fe-S-Au association, and also from immediately above or below unconformity surfaces. A total raliance on the current syngenetic model for Witwatersrand gold does not appear to be justified from the accumulated data and may be responsible for missed opportunities during exploration: consideration of other models is suggested especially where they better fit the data. The stratabound natura of Witwatersrand gold 1& critical to mining, but is emphasized in syngenetic models to the virtual exclusion of many other important observations. By analogy with other deposit types, stratabound character is probably a poor guide to genesis.

Jan 1, 1988

By R. W. Barbaro

The limitation of sulfur dioxide in power plant emissions dictates that sulfur in coal be reduced to the lowest possible level before combustion so as not to aggravate the emission control problem at the stack. For coal fired power plants, the methods in practice to achieve low sulfur coal include mining areas with relatively low sulfur. reducing sulfur in the mined coal through preparation techniques and blending high and low sulfur coals. A prerequisite to the successful implementation of any of these practices is the knowledge of the spatial distribution and the capability to predict sulfur values in a coal seam.

Jan 1, 1988

By Lindsay Norman

To many who for years have scrutinized the US mineral supply picture, recent, often strident debate on present-day security of many critical mineral supplies echoes sentiments repeatedly expressed in the past decade by the minerals industry. At no time since the last world war has such a flurry of public concern been expressed for the economy's mineral sector. Where once mineral availability problems were relegated to the newspaper's business section or not reported at all, today comprehensive analyses of our international mineral posture are discussed in detail by some of the nation's most respected and widely read periodicals. In past years, disinterest was also experienced whenever the mining industry attempted to carry its message to Congress, the public, and the government's executive branch. Among minerals professionals, the past decade was a time of particular frustration clue to serious erosion ill US ability to competitively produce the vast array of raw materials vital to the economy acid national defense. Fervent calls for immediate attention were simply not answered. These professionals have understood that mining and agriculture are the primary sources of wealth, fulfilling virtually all needs and creating and sustaining jobs. Why then has it been so difficult to raise the consciousness of the American public, and even more surprisingly, of the government and national leadership? The answer to this question is perhaps endemic to how government functions, but pore important, it begs that mining professionals capitalize on the opportunity and the attention now at hand. Carefully conceived and implemented actions by both private and public sectors are needed more than ever before in the past 35 years. To this end, it is vitally important to seek out and resolve the root causes of supply problems and not dwell on superficial solutions. The following discussion attempts to establish a simple framework to view this process. It does not presume to be an exposition of cause and effect, but hopefully identifies some needed steps. Growing Awareness in the 1970s Of all events stimulating current concern, certainly the OPEC oil embargo has left the deepest impression. It was inevitable that after such a shock, man. Americans would begin asking whether the US was as vulnerable to cutoffs of minerals as it was to oil cutoffs. Then, when serious trade security questions surfaced in sonic mineral-rich nations in Africa and the Persian Gulf, the ominous term ''resource war" began to be heard. Countries such as South Africa, Zaire, Zambia, and Zimbabwe have suddenly become key areas for testing our national security resolve. As the US witnesses the influx of Marxist influence in many sub-Saharan exporting nations and the rising threat to free world access to critical materials and energy, the assurance of adequate supplies is becoming a national issue at last. The US is now learning that self-sufficiency for many vitally important mineral commodities has vanished. Of course, it did not vanish overnight; it had been leaking away for years, and the trend was noted by industry and a few in government. Within the minerals community, suspected weaknesses in America's resource posture were sought and found. As a result, the country's heavy reliance on foreign sources fur more than a score of minerals, many extremely vital to security, has been forcefully documented and the case for drastically altering the supply unbalance hits been proposed. The renewed concern for national defense is central to almost all proposals for minimizing US foreign mineral dependence. It is not surprising that many of the voices heard today on the dependency issue are active members or alumni of the militate establishment. Unfortunately, their almost total focus on the security aspects of dependency has tended to obscure important underlying issues which are not directly defense-related. Some of the proposals advanced might mitigate the deeps-dency problems, but they still fall short of curing the underlying problems that have led to a steady loss in mineral self-sufficiency. In almost all instances these problems call be traced to increasing government influence on the free market minerals economy. Some national security proponents seek to attain total self-sufficiency in minerals. Such arguments must he tempered by existing realities. It is easy to demonstrate that the US obtains substantial quantities of sonic essential minerals from potentially insecure sources abroad. That the US will continue to do so in the foreseeable future is not in doubt Uncertainty begins, however, when we try to interpret the significance of these facts. It is important to understand that mineral dependency does not irrevocably lead to vulnerability. Unlike oil, no mineral commodity combines the same degree of universal indispensibility and centralized foreign control of supplies. Moreover, although many US-required minerals are produced by fewer countries than export oil, those minerals cannot approach petroleum in economic or industrial importance. Finally, most foreign supplies come front friendly, secure nations such as Canada, 'Mexico, and Brazil. This, aid more, constitutes a vital element in US economic health as a world trading nation. The Cost of Interruption The US is currently stronger and more resilient than many expected after absorbing the oil embargo shock and subsequent price increases. Nevertheless, major worldwide

Jan 6, 1981

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By J. Urosek

Since the promulgation of the Mine Safety and Heath Administration?s (MSHA?s) Final Rule on mine seals (30 CFR § 75.335(b)), which became effective on October 20, 2008, many seal designs have been approved by MSHA and constructed by the mining industry. Since the effective date of the Final Rule, several issues on the design, construction, and/or inspection of seals have been brought to the attention of MSHA. Several such issues discussed in this paper include; the directional, design-load criteria required by MSHA for 50-psi seals, 120-psi seals, and greater-than-120-psi seals; the presence of fireclay in the surrounding strata where a mine seal is to be built; the measurement of convergence of the mine opening in which a seal has been constructed; where gob-isolation seals can be used; and the importance of periodic inspection of seals.

Jan 1, 2010

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany's dominance of the world's dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999