Search Documents

By S. Monette, D. B. Dreisinger, D. Vleeschhouwer, G. B. Harris, G. A. Kordosky

A new process for the recovery of pure (>99.95%) palladium and platinum is described. The process, which has been tested at the pilot scale, comprises (i) the simultaneous solvent extraction of palladium and platinum by a new Schering Berlin reagent, TN 1911, (ii) washing of the loaded extractant to remove co- extracted impurities, and (iii) differential stripping of first platinum at pH 3, and secondly palladium with strong hydrochloric acid, and (iv) precipitation of palladium and platinum salts, followed by reduction to metal. The process is, unusually, a non-ammonia one requiring only small amounts of ammonia at the end where final purification may be necessary for particularly complex feed solutions.

Jan 1, 1993

By Francis S. Kendorski

INTRODUCTION Caving offers the lowest cost per ton of any large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently taken on new importance as deeper lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface min¬ing methods, and too low grade to support any type of underground mining except a bulk method such as caving. Announced discoveries or indications that may be amenable to caving include: Climax's Mt. Emmons molybdenum discovery in Colorado; Molycorp's Goat Hill molybdenum prospect in New Mexico; the Phelps Dodge molybdenum deposit in Beaver County, UT; Arizona copper occurrences such as Asarco's Sacaton, Hanna's Casa Grande, Noranda's Lakeshore, and Ken¬necott's Safford; Anaconda's suspected deep copper de¬posit in Butte, MT; Anaconda's Carr Fork, UT, deposit; and perhaps others. CAVABILITY'S ROLE IN FEASIBILITY STUDIES Caving is a system of underground mining which removes support from underneath an ore body. As a result, the rock mass fractures, fails, and flows vertically downward by gravity to be collected in previously ex¬cavated funnels. Types of ore that have been mined by caving include molybdenum, copper, iron, nickel, as¬bestos, and diamonds (Julin and Tobie, 1973). It is primarily a large-scale method, with production rates of more than 45 300 t/d (50,000 stpd) having been achieved. However, the initial capital investment before return is very high, often in the hundreds of millions of dollars. The cavability of an ore body or mineral occurrence is a critical item in the feasibility study of a proposed mine, not only from the point of overall minability, but from the point of impact on other costs such as blasting, loading, hauling, crushing, and grade recovered. Aside from the often-asked question of, "Will it or will it not cave?" the real questions are, "Can we afford to make it cave, carry the rock away, and extract the mineral?" The last is not a topic of this chapter, but the first two are. The cavability of an ore deposit or mineral occur¬rence is based on many things, but clearly, if a large enough area is undermined, any rock mass will cave. The result could be a violent collapse as occurred at Urad, CO (Kendrick, 1970), or perhaps the rock mass will cave beyond the ore boundary. Another unfavor¬able result could be ore blocks that are too large for the equipment and orepasses to handle without considerable secondary blasting. Weak rock with numerous fractures may produce a very fine ore when it caves, resulting in dilution and ground control problems. DETERMINING STRUCTURAL DOMAINS It has long been recognized that the geologic nature of an ore body is important to cavability (King, 1946). Such items as weak rock material, intensity of fractur¬ing, and severity of faulting all contribute to the success of a caving operation, and information regarding these is required as a minimum for the cavability determination. In practice, the rock mass-defined as the blocks of intact rock together with the intervening fractures, joints, faults, bedding planes, and other discontinuities-that contains the ore body, as well as the surrounding and overlying rock, must be examined in a systematic and detailed fashion. Surficial geology maps must be pre¬pared, exploration holes drilled, and core logged for en¬gineering information. The fracturing of the rock mass must be studied to ascertain the three-dimensional dis¬tribution of fractures and their characteristics, and faults must be located and described. The strength and other mechanical properties of the rock material, the fracture surfaces, and the fault filling materials must be tested and reported for later use by designers and planners. With this basic information and an understanding of the geologic setting, the rock mass can be divided into one or more structural domains which tend to behave similarly in response to engineering activities (Robertson and Piteau, 1970). One must keep in mind that the determination of the structural domains goes beyond the geologic units present. Several lithologic units may be lumped together, while a single lithologic unit can be divided into multiple domains. Major faults often form their own domain, and the direction of engineering ac¬tivity-for example, cave advance to the north rather than the south-may alter rock mass behavior, resulting in different domains. As an example of the detailed rock fracture map¬ping required for such studies, the structural domain determinations at the Climax mine (Kendorski, 1973) are shown in Fig. 1. The circles are Schmidt equal area projections of the three-dimensional attitudes of frac¬tures (Ramsay, 1967) mapped in detail at various rock exposures. The attitude of fractures is important to the cavability determination since it dictates the directional behavior of the rock mass as it fails, and determines the effectiveness of arching, keying, and rock block inter¬locking. Low-angle fractures must be present to allow movement of the rock in the vertical direction during undermining (Mahtab and Dixon, 1976); if low-angle planes of weakness are absent, the rock mass may arch with a keystone effect, rather than moving vertically downward.

Jan 1, 1982

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By John J. Gillis

There is an ongoing battle to gain general acceptance of fossil fuel byproducts as safe, economical and useful agro-industrial materials. Despite that, the US ash industry is witnessing a steady growth in the volume of coal burned, along with the production of greatly refined, higher-quality ash particulates. There are two principal reasons for this. Economics have caused an increasing number of US electric utilities to convert from oil-burning to coal-burning. And the Federal government has tightened specifications on fly/bottom ash production quality. Hence, it must be noted that new and more stringent Federal regulations were implemented in 1980. The resultant ash particulates are finer, more compact, and less heavy than in previous years. Additionally, the first shift from oil to coal in the US was initiated in December, 1979 by the New England Power Co. in Massachusetts. Coal is the most widely-distributed fuel in the US. And it is found in 38 states. The wide availability of this fossil fuel and its general cost-efficiency, coupled with the undaunted move of US electric utilities toward nuclear power, are major factors affecting the current statistics on ash generation (65.4 x 106 million tons). Interest in the use of coal in power plants is creating a unique ash disposal and use situation for ash producers as well as the Federal government. There are growing quantities of fly/bottom ash residue. Ash producers must decide how this byproduct can be dealt with effectively and profitably. At the same time, government agencies such as the US Environmental Protection Agency (EPA), are commissioned by Congress to assure that solid, liquid, or gaseous material released into the environment is not harmful or offensive to human health and the environment. Additionally, the Federal government is often responsible for establishing and enforcing guidelines and standards governing the use of recycled materials. Several standards and guidelines governing the properties and use of ash in the US have been established by governmental agencies as well as by the ash industry itself. Of these, some have been developed for ash use by a specific federal agency. Others apply to the entire industry. The following is a brief identification of the major specifications for fossil fuel ash: • US Corps of Engineers - These specifications were first established in 1957. They delineate the physical and chemical requirement for pozzolans used in mass concrete. These specifications applied only to Corps of Engineers' concrete construction projects for locks, dams, and other mass concrete projects until 1977. At that time, a joint effort between the American Society for Testing and Materials and the Federal government produced a modified specification that is now generally applied. The Corps of Engineers' ash, however, retained certain aspects of its specifications for its own use, particularly in the area of handling and shipping fly ash to its own projects. Prior to transporting the fly ash to the corps, all potential sources for the ash must be inspected and approved as a supply source. All silos must be filled, sealed, and tested before the ash is released for shipment. The normal test period for the ash is seven days, although several testings may require up to 28 days. Once the fly ash has been released, it can only be shipped to US Corps of Engineers' projects. All shipments are made with a government inspector present during loading. After a truck or railcar is loaded, the silo is resealed until the next shipment. This procedure requires three silos, and a minimum of 454 t (500 st) each should be considered for each storage unit. All silos are strictly committed to Corps of Engineers' use and are not available for other commercial shipments. • US Bureau of Standards - This Federal agency maintains a standard testing sample of nearly every product used in the US. The accuracy of the fly ash chemical analysis is measured by a regular cement and concrete reference laboratory (CCRL) inspection and based on test results from a standard sample of cement. • US Bureau of Reclamation - This agency pioneered several projects using fly ash and required Federal Standard Certification for pozzolans. • American Society for Testing and Materials (ASTM) - This nongovernmental organization began preparing standards for fly ash sold and used in the cement and concrete industry in 1947, at the urging of ash marketing firms. Current standards define chemical and physical requirements and is entitled, "Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Portland Cement Concrete (C 618-80)." • State Highway Specifications - Led by Alabama, many states are moving toward permitting - and in some cases requiring-the use of fly ash in portland cement concrete and with lime for base stabilization projects for roads and highways. • Federal Aviation Administration (FAA) - The FAA acts in an advisory capacity. It has final approval on design specifications for airport construction projects. The agency has established a set of guidelines permitting the use of fly ash, and has approved several fly-ash-specific designs. The most current FAA fly ash projects

Jan 8, 1984

By J. G. Groppo, D. J. Sung, B. K. Parekh

Hyperbaric filtration for the dewatering of fine coal cleaned by froth flotation was evaluated on a laboratory scale. A laboratory pressure filtration procedure designed to obtain a uniform cake structure from dilute slurries containing a significant amount of coarse material is described. Baseline tests were conducted to determine the optimum operating conditions for the eventual application of the process to a continuous pilot-scale hyperbaric filter. Investigated were filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH.

Jan 1, 1996

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By Fathi Habashi

WHILE HYDROGEN SULFIDE precipitates metal sulfides from aqueous solutions, other gases such as sulfur dioxide, carbon monoxide, and hydrogen, under certain conditions, precipitate the metals directly. This can be achieved at high temperature and pressure. Such processes are of great technical importance, since metals of high purity are precipitated economically in a powder form. As a result of the availability of such powders on a large scale. processes for compacting metal sheet and other mill forms directly from the

Jan 1, 1970

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By Michael J. Martinson

Mine ventilation has been evolving as a separate field of study since the middle of the nineteenth century, and some practitioners might assert that mine ventilation has come of age as a discrete field in the last decade or two. Certainly the extensive literature now available on many facets of the subject, international congresses, the phenomenal upsurge of interest in mine ventilation in the United States of America since the passage of the 1969 Federal Coal Mine Health and Safety Act, and the existence of a virile mine ventilation society in South Africa with its own monthly journal all point in this general direction; on the other hand the lack of a rational design philosophy for ventilating mines suggests that mine ventilation may still be on the threshold of maturity. To generalise, many mines are still ventilated simply to comply with arbitrary statutory regulations, or with some ill- defined notion of reducing the risk of injury associated with the atmospheric environment in mines. Hazards in this category include oxygen deficiency, toxic gases and particulates, pathogenic gases and aerosols, explosive gases and dusts, and extreme climatic conditions. Although many mines are ventilated to abate the risk of a specific injury, there is inevitably a spectrum of latent and patent atmospheric hazards in every underground mine. The writer (Martinson, 1976) has previously drawn attention to the dearth of material on mine ventilation design in textbooks and technical journals, and to the overly simplistic approach sometimes adopted in the limited work published on the subject. The available material undoubtedly contains useful technical data and persuasive views, but seemingly could not be used to demonstrate the rational engineering approach to mine ventilation design advocated in the present paper. The range of papers presented at the 1975 and 1979 Congresses, and the diverse interests and affiliations of delegates, emphasize the multidisciplinary nature of mine ventilation. Easily recognisable topics include: Fluid mechanics Thermodynamics Heat transfer Flames and combustion Aerosol physics Radiation physics Geophysics and geomechanics Occupational diseases Epidemiology Industrial physiology Despite these heterogeneous connections there can be little doubt that mine ventilation is fundamentally an engineering field and not an off-shoot of some other branch of applied science. The distinction is important because mine ventilation has essentially developed as a form of ad hoc trouble- shooting, and in the process mining engineers have relied extensively on the assistance of experts drawn from other fields. Thus historically there has been limited scope for the application of rational design techniques, and personnel enlisted from scientific disciplines may not have had any previous experience in the intricacies of engineering design.

Jan 1, 1980

By B. T. Stanley

The basic geological data, derived from boreholes, exploratory test pits, drivages, and mine development, include information on parameters such as ore thicknesses, grades, depths below surface, structural attitudes of beds, rock types, and lithology of beds overlying and underlying the deposit. These data are usually supplemented by analytical information obtained from more detailed chemical, physical, and structural investigations of the various horizons. Even then, the relatively small number of sample points in the ore body and the sparsity of the sample volume make it necessary that the available information be interpolated between sample points and extrapolated into areas beyond the limits of the sample points. Such interpolation and extrapolation are usually done by making suitable assumptions about the parameter's continuity in the ore body and by building a suitable mathematical model. The mathematical model provides the values for chosen parameters at the nodes of superimposed conceptual grids of any desired dimensions such as a grid cell equal to the size of a mining block or any other criterion. This network of values, for any parameter, can then be used for mine planning, designing, and controlling functions. Additionally, these data can also be used to calculate ore reserve and quality in total and/or for any required block. Figs. 1 and 2 broadly illustrate the scope of work that may be involved in a geological ore-body modeling study for a coal deposit. Figs. 3 through 6 describe the scope of a commercially avail- able computerized system (MEDSYSTEM of MINTEC, Inc.) for creating drill-hole data base, mineral inventories, and for planning coal and uranium projects. The application of MEDSYSTEM to calculate reserves and to long-range planning in steeply pitching coal deposits is described in subsection 3.4, Chapter 4.

Jan 1, 1979

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By R. Fedel-Moen, R. W. L. Kimber, B. D. Williams, S. R. Ragusa

The use o f cyanide to extract gold from ores is widespread. In the process of extracting gold, cyanide may form metal cyanide complexes with a variety of other metals present in the ore. This study was carried out to investigate the biodegradation of the Cu(I)-cyanide complex and tetracyanonickelate under varying pH and nutrient additions. Detailed studies using shake flask cultures and bioreactors showed that naturally occurring bacteria residing on gold-leach-pad ore uti¬lized the Cu(I)-cyanide complex (CuCN) and tetracyano-nickelate, Na2(NiCN4), as carbon and/or nitrogen sources. Ammonium-nitrogen (NH4+-N) and/or cyanate (CNO-) accumulated in solution as the metal cyanide complexes were degraded. The accumulation of cyanate as a product is a concern due to its toxicity. Degradation rates were increased if a growth substrate (peptone, 0.1%) was added to the medium or if bioreactors were primed with peptone before addition of the metal-cyanide complex. Tetracyanonickelate was degraded at pH 8 without added peptone, but it was not degraded at pH 10. The addition of peptone was required for degradation of the Cu(I)-cyanide complex at pH 8 and pH 10. At pH 8, the addition of peptone resulted in the accumulation of cyanate, whereas, at pH 10, cyanate was not detected in the cultures. Biodegradation of metal-cyanide complexes was faster (approximately 1.5 to ten times faster) in bioreactors than in shake flask cultures. The addition of peptone was not required for degradation of metal-cyanide complexes in bioreactors. However, priming the bioreaetor with peptone resulted in higher metal-cyanide degradation rates over multiple cycles.

Jan 1, 2000

By G. T. Lineberry, W. J. Wiehagen, L. L. Rethi

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: •job definition through task analyses, •the ranking of job elements by perceived cost consequence, •observational techniques to establish performance baselines, and •cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technological efforts but include consideration of the so-called "soft-skill technologies, " aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

Jan 1, 1996

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982