Search Documents

By Stanislaw Wasilewski, Zdzislaw Krzystanek

Ventilation process in deep mines features relatively low efficiency. Commonly used passive control by means of regulators and flow throttling leads to remarkable energy losses that could be lower if effective monitoring and remote control of main fan operating point were implemented. In the paper, some results of investigation carried out in Polish coal mines to evaluate real energy losses in ventilation process are described. Different methods for main fans performance monitoring and control are considered and compared especially those using fan drive speed control to minimize power consumption. On the other hand some criteria for power evaluation are analysed and algorithms for optimum location of controllers in ventilation network are considered. The results of investigation are being implemented in the first system for monitoring and control of main fan operating point in Miechowice colliery.

Jan 1, 1995

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By Gerald V. Jergensen, Edward J. Samuel

Slurry system are the principal method for storage and transportation of solids within and between concentration operations In a mineral processing plant. A slurry 1s a mixture of solid particles In water, or a chemical solution, that behaves like a liquid. The design of slurry transportation systems is generally analagous to pumping and piping water, but with a few notable exceptions: • The interaction of particle on particle affects slurry transport. • Particles often interact with the fluid, particularly when chemicals have been added to the system. • Particles have a frustrating tendency to settle from the slurry suspension, especially into locations not considered In the design. • Solids have an affinity for wetted surf aces and tend to wear them away. Slurry transportation systems Include a number of separate components, each requiring special design considerations. A systematic evaluation of each component of a slurry transfer system will help overlooking the small details that could cause operational headaches. Most slurry transport systems include: • A receiving sump or tank that provides for mixing and/or momentary storage of slurry. • A driving force.. by a pump, atmospheric pressure or gravity. • A suitable conduit for transportation.. pipes or launders. • A delivery objective.. another sump or process vessel, or distribution system to several process points. • A control strategy and design to regulate the transfer operation. The design of the slurry transportation system normally evolves through the following steps: • Finalizing the process flowsheet and establishing the weights and volumes to be handled. • Identifying and characterizing the various process fluids and slurries. • Defining critical and minimum transport velocities of fluids. • Selecting a pipe diameter (or dimensions and gradient) and

Jan 1, 1986

As discussed previously, total cost is the sum of the direct materials, direct labor, and production overhead costs. The assignment of direct materials and direct labor costs to individual activities is generally straightforward. The assignment of overhead often is not. Overhead costs frequently contain allocations that only approximate the demand the activity has made o; the overhead resources. The inaccuracy of the overhead calculation can create erroneous production cost information and lead to suboptimal management of the operation. This problem is particularly acute when determining the production cost of individual products in multiproduct firms. Pricing, process management, and product mix decisions are especially susceptible to errors in product costing. The problem of properly determining production cost is complicated by the fact that few if any alternative methods exist to identify the inaccuracies in overhead allocation. To avoid errors, some firms simply ignore overhead costs in their product cost calculations, particularly those resulting from marketing and distribution of the final product.

Jan 1, 1999

By Chester R. McKee, Amar C. Bumb, Kohei Kawakita

Unlike many other heavy metals, gold can be profitably mined in small operations because of the prices. One mining technique that seems ideally suited for small deposits of gold and for certain large, lowgrade oxidized disseminated deposits is solution mining. Solution mining generally requires lower capital investment and operating costs than conventional mining and milling and is safer and less degrading to the environment. Although gold has long been recovered by cyanide leaching following conventional milling, solution mining as discussed here gained momentum only in the past two decades, during which time alternative lixiviants instead of cyanide have been researched. Chamberlain and Pojar (1981) classified solution mining systems used today as three types, namely heap, dump, and in-situ leaching.

Jan 1, 1990

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By Maria S. Adusumilli, A. Bhaskara Rao

ABSTRACT The presence of gold in lateritic crusts over mafic and ultramafic volcanogenic complexes in / and greenstohe belts, has called the attention in several parts of Brazil and also in Australia. Recent studies reveal the variety of structures and mineralogy of such crusts, and their importance in correlation with host(bed) rock types, as exploration guides, specially for greenstone belt metallogeny. The expected nature of growth of plates and/or nuggets in such crusts is under detailed study, and is considered as possibly due to dissolution and reprecipitation phenomenae of disseminated-fine-low grade ore in the host rock, in this investigation, laterite geochemistry, though incipiently discussed todate, is of fundamental importance and significance. Lateritic gold can be classified texturally as: dusty and diffused, fine, thin platy, taDular, and nuggets. Such gold is pure, and is often restricted to nodular (pisoliths, ooliths, concretions) forms or the matrix, that constitute the crusts or lateritised gravel beds which have an essentially goetnitic nature. Further this gold is recovered directly by mining the crusts or the adjoining placers with the metal derived from them. The thickness and extension of laterite crust zones is extremely variable depending oh the paleoclimatic conditions, and is conditioned to the favourable lithology and its structural expression. However, the "growth" of gold in these laterites will be conductive , without doubt, to several small scale mining activities, specially in the developing countries and regions limited to latitudes 309N and 309S.

Jan 1, 1987

By C. Ceccarini, I. Salvadori, G. Oggiano

GENERAL BACKGROUND The first mention of the presence of bauxite in the mesozoic series of north-west Sardinia (fig. 1) is owed to Oosterbaan, a Dutch geologist, who carried out a geological survey of the area in the ninetten thirties. A more detailed study of the mesozoic series was attempted in the fifties by Pecorini and other, who concentrated particularly upon the stratigraphy of the bauxitic horizons, through examination of the various outcrops. In the sixties a pining company, Monte Amiata S.p.A., turned its attention to a section of the deposit outcropping near Olmedo and, considering it to be of some promise, carried out prospecting works consisting essentially of various trenches, some bore holes, a few adit and a. layout plan for the preparation and execution of trial exploitation. The results, although positive, did not convince the company's shareholders to continue the exploration. This report, which is intended as a new contribution to knowledge of the Sardinian bauxite deposit, takes into account the information acquired not only from a drilling prospection begun in 1979 in connection with the SOMIT-PROGEMISA joint venture, but also the results of structural studies and numerous chemical, mineralogical and

Jan 1, 1984

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

By George E. Aiken, B. R. Jr. Waples

INTRODUCTION In this paper the author will attempt to bridge from the paper work of design and engineering to the reality of implementation. Certain facets of construction are constant to a successful project, no matter the level of technical complexity. Basic to timely, low cost construction are the people assigned to the project. Construction is not accomplished by robots, computers, or speeches; but rather by people. People do however require the avail- ability of equipment and communications to properly complete the work. ORGANIZATION Good organization is the basic requirement of a well implemented construction project. For this paper the author will suggest an organization chart as well as an activity listing that together support the construction activities. There is little difference in the activities or functions needed to construct a small plant or a large one. It is a matter of how much time an individual has to spend on an activity that determines the structure of an organization. The difference between a large and small plant construction job is often described as the multiple hat versus the single hat philosophy. As an example, a resident construction manager on a small job might be the manager, the field engineer, the scheduler, the estimator, and the procurement manager. At some time during a construction

Jan 1, 1986

By D. M. Sloan

While surety capacity for the mining industry continues to shrink, States are demanding greater financial certainty for closure/post closure obligations. To combat these demands, larger mining companies are pursuing a Mining Surety Reinsurance Program that requires a significant up front capital contribution. This paper outlines an alter-native program for middle market mining organizations. The program utilizes a “Blended Finite Risk” environmental insurance solution with surety acting as the “front” in states where insurance is not an acceptable form of collateral. Marsh proposes creating separate programs for each State requiring surety. The reason for separate programs stems from each states’ different surety rules. Insurance companies typically require at least $5 million in future value remediation liabilities for finite risk programs. Since most middle market mining companies have obligations that fall below this threshold, the Blended Finite Risk Program contemplates combining several companies closure/post closure liabilities to accomplish the minimum amount required by the insurance company. Why use a Blended Finite Risk Program? One of the primary benefits is the financial assurance that funds will be available for planned remediation. For example, the financial assurance may be required by a government agency. The certainty may help facilitate a merger or acquisition. Additionally, the funds may be part of a CER-CLA PRP settlement. In all cases, the insurer providing coverage would be a secure independent 3rd party. A Blended Finite Risk Program also provides a long-term solution – up to 30 years and in some select cases longer. The benefit to a state or the BLM is the removal of financial uncertainty. An insurance company writing the policy would have an AA or AAA balance sheet. The hardening of surety markets coupled with the tightening of financial assurance requirements in many states have necessitated the posting of 100% collateral. This program substantially reduces these collateral requirements.

Jan 1, 2004

By A. L. Mular

Introduction The cost of grinding may be divided into a fixed equipment cost portion and an operating cost portion. The fixed equipment cost is the amount of money required to purchase the grinding mill itself. This amount may be kept separate from the installation cost which, often, is taken as a percentage of the fixed equipment cost. A good average is 43%; therefore a $100,000 ball mill would cost approxi¬mately $143,000 installed. Operating costs are variable and paid per unit time for power, liner replacement, grinding charge replenishment, labor, and mainte¬nance including major parts replacement. Such costs depend on the geographical location and will vary with the cost of labor. Operating costs are difficult to estimate. Most mining companies consider such information proprietary. This section provides a means to obtain an estimate of the equip¬ment cost of a grinding mill with a rated accuracy of±l0%. Compara¬ble methods to determine operating costs are not available. Such costs are presented in table form with suggestions for updating them. Esti¬mating the cost of liners and steel replacement is possible as described in a later section. Capital Costs of Grinding Mills Grinding mill costs have been related,124 by means of equations and corresponding graphs, to the nominal horsepower requirements of mills. All graphs are based on a Marshall and Stevens cost index for Mining and Milling of 300, where a cost index is a ratio used to estimate current prices of equipment from obsolete prices. Where (Cost Index Now) Cost Now = (Cost Then) (Cost Index Then) (I) For example, the cost of an autogenous mill that requires a 3000¬hp motor is estimated as $500,000 (Fig. 95). This was the estimated price when the M&S (Marshall and Stevens, Mining and Milling) cost index had a value of 300. If the index is currently at 400, then the estimated current price of the autogenous mill is: Cost Now = ($500,000) (400) (300) = $667,000 Most professional journals will publish current values of cost indices at least once a month. In subsequent pages, each graph of grinding mill cost vs. mill horsepower has an associated graph of capacity vs. horsepower along with a table that relates mill size to horsepower. The associated graph and the table must be used with caution, since both apply to an average ore under average conditions. Example calculations showing how graphs should be used are shown in the following. It should be stressed that the cost data incorporated herein ex¬cludes the cost of pumps, motors, lines, and classifiers, unless other¬wise stated. Costs are not direct quotes; they are the averages of quotes supplied by manufacturers and analyzed by means of regression analysis. Example 1. Calculate the power required to grind 100 tons of dry solids per hour (in a closed circuit with a classifier) when the

Jan 1, 1985

By David G. Chedgy

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health administration (OSHA) are accepted by MSHA relative to caal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By Donald D. Haas

This presentation will discuss a mine owner's evaluation to utilize a contract miner in the development and production of gold properties. I will address both the quantitative and subjective aspects of the evaluation process. The quantitative aspects include cost evaluation, capital preservation, acquisition and disposal of new and used equipment, administrative costs, recruiting and training, and organizing a staff and craft labor force. The subjective areas of this discussion include corporate philosophy, administrative concerns, contractor competence, loss of owner control, operating flexibility, financing assistance, recruiting and training program utilization and risk reduction. The evaluation of alternatives provides a system for comparing, on a cost basis, an owner/operator system vs. a system using a contract miner. The supplement provides a concept on how a contract miner may be the cost effective system to be utilized.

Jan 1, 1989

In May 1993, SME contracted with The Dolecek Companies of Denver, CO to conduct a salary survey and a study of Mining Engineering. A written, four-page survey was sent to a random select sample of 1897 current SME members from the United States and Puerto Rico and to 40 current SME members from Canada. A total of 621 survey responses were input and analyzed, to guarantee the validity of the survey findings. The findings are representative of the entire SME membership. And the survey is within a statistical range of accuracy of plus or minus 5%. Salary survey SME members currently earn an average of approximately $60,000 a year. Some 45% earn less than $60,000 and 49% earn more than that. About 24% of all SME members earn $80,000 or more each year and 13% earn $100,000 or more. Not surprisingly, a statistically greater number of owners (27.5%) and those in senior management (30%) have a current income or salary of $100,000+ a year.

Jan 1, 1993

By William E. Wallace, Michael J. Keane

This review summarizes three sets of ongoing studies which we are performing in collaboration with a number of researchers associated with the Dept. of Interior - Generic Mineral Technology Center for the Study of Respirable Dusts, concerning surfactant-particle interactions studied using this surrogate surfactant. These topics are: (A) the suppression of mineral particle cytotoxic potential by DPL adsorption and the persistence of this effect under conditions of enzymatic digestion; (B) surfactant suppression of organic particle cytotoxicity by DPL adsorption and the effect on subsequent expression of genotoxic potential; (C) potential effects of surfactant on heterogeneous structured complex respirable particles. The references list some of our reports which can provide additional information on these studies. Further, those reports provide references to the literature of the field and to the works of others on these topics. Deep lung airspaces, the pulmonary alveoli and respiratory bronchioles, are coated with a hypophase which is rich in surfactant biomolecules secreted by the alveolar type II epithelial cells. The surfactant is known to be critical to maintaining stable low surface tensions on the inner surfaces of the alveoli by forming a surfactant layer on the airliquid interface of the alveolar hypophase. Upon deposition in the acinar regions of the lung a respired particle's initial contact will be with this surfactant coating over pulmonary tissue. A primary component of this surfactant is the phospholipid diacyl glycerophosphorylcholine, commonly called lecithin. A surface layer of dipalmitoly lecithin on saline will act much as full pulmonary surfactant in decreasing surface tension and producing a hysteresis in surface tension behavior with surface area. We have used dipalmitoyl glycerophosphorylcholine, or dipalmitoyl lecithin (DPL), a major component of that surfactant, dispersed in physiologic saline as a surrogate for studying interactions of both mineral and organic respirable particles with pulmonary surfactant and consequent effects on particle toxic behavior. A. DUST CYTOTOXICITY AND LECITHIN SURFACTANT ADSORPTION Respirable quartz and kaolin clay particles are found to be comparably cytotoxic in a number of in vitro bioassays including lavaged rat pulmonary macrophage release of cytosolic and lysosomal enzymes, and red blood cell hemolysis as a measure of dust membranolytic potential. These direct and prompt cytotoxic activities do not account for the distinctly greater potential for quartz to induce pulmonary disease. When respirable quartz and kaolin are incubated with a dispersion of DPL in saline at 37C it is found that the prompt cytotoxicity of both dusts is fully suppressed as measured in vitro by pulmonary macrophage release of lactate dehydrogenase, beta-N-

Jan 1, 1991

By Robert A. Jankowski, Fred N. Kissell

Recent allegations about tampering of coal mine dust samples have led to suggestions that the coal industry needs a respirable dust compliance sampling method that is less subject to tampering. The sampler designs under consideration include fixed location monitors that could be mounted on a mining machine or located at a stationary location in the mine, and samplers that are worn, like the existing samplers. Fixed-point samplers have a design advantage, since samplers worn on the body will have size and weight limitations. On the other hand, in some cases there are respirable dust concentration gradients, which will dictate careful placement of a fixed-point sampler inlet to determine the exposure of workers. This study examined dust concentration-gradient data obtained by the Bureau of Mines and others over the last decade. As an example of spatial gradients at continuous miners, a fixed-point monitor located in front of the operators cab shows a higher dust concentration than a sampler located on the operator and reduced exposure when the sampling location is behind the operator cab. It may be necessary to use a sampling tube with a machine mounted monitor, to sample in the operators breathing zone in the cab to provide a more representative sample of the miners exposure. For face workers on longwalls or on continuous miner sections using remote control, the study shows significant dust level gradients and gradient variations between typical operator positions and mining machine locations. In addition, if fixed-point monitoring is used to monitor an area, vs the exposure of specific workers, dust control technologies currently employed to ensure reduced dust exposure such as the diversion of dust laden air away from the workers, or through the use of remote control of mining machinery may not indicate the same dust reduction obtained with current sampling techniques.

Jan 1, 1993