Search Documents

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By R. M. Morris, G. A. Matthesius, M. J. Desai

Slow pyrolysis experiments were caried out on samples of coal from north em Natal having a volatile mater content ranging between 10 and 25 per cent by mass and a constant particle-size distribution. The tests were conducted at atmospheric pressure in a helium atmosphere, and ata heating rate of 10 KImin and a final temperature of 1220 K. The pyrolysis products were taken as coke and volatile mater (tar and eight other species), and tMir respective yields were measured. The experimental results were used in the modification of an existing mathematical model and in the derivation of new corelations for some of the parameters of the model, so that the volatile products of a coal can be predicted from ultimate and proximate analyses of the coal. The pyrolysis tests showed good agreement between the model predictions and the experimental results.

Jan 1, 1987

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By I. M. Wolff, M. B. Cortie

The Stainless Steels '91 Conference, which was held in Chiba, Japan in June 1991, was the fourth in a series of related international conferences on this theme. These conferences have a high profile and currently constitute a premier forum for exchange between researchers and industrialists active in stainless-steel technology.

Jan 1, 1991

By A. W. S. Schumann

SYNOPSIS The most economic exploitation of South African coal resources requires sustained study of the balance between known resources and the predicted rate of consumption, against the background of the development of other sources of energy in South Africa and relevant developments elsewhere in the world. A number of the major issues which would arise in such a study are discussed, including the need for a standardized South African definition for coal resources, the merits of sectoral forecasts of consumption compared with global forecasts, the encouragement of a higher recovery from reserves, and the development of an export market for South African coal.

By G. A. Brown

A colloquium on industrial minerals entitled' A Strategy for Growth in the Industrial Minerals Sector' was held at Mintek on 5th November, 1991, under the auspices of the Extractive Metallurgy Sub-Committee of the SAIMM. The SAIMM had not been previously active in the field of industrial minerals, and the programme was designed to appeal to the middle management of mining and manufacturing companies in the industrial-minerals field. A total of 86 registered for the Colloquium, a predominance of the delegates (65 per cent) being non-members of the SAIMM. Two overseas delegates were registered after announcements

Jan 1, 1992

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

n interesting situation arose last week when two Vaal River residents wrote to me (and a third telephoned) giving me details of how Sasol wanted to develop an open-cast coal mine on the south bank of the Vaal, just upstream of the Barrage. This is agricultural land and is across the river from Millionaire?s Row, where a number of wealthy people have built river-side mansions. The mine would be hidden by a 30 m-high (10 storeys) earth wall set 300 m back from the edge of the river. It could operate 24 hours a day.

Jan 1, 1996

For many of us, formal academic education slows abruptly when we leave a tertiary institute of learning. We start applying and connecting newly acquired knowledge with the practicalities of a career, and begin to think in a manner that is technology-oriented. Subsequent vocational advancement is offered by the .many mining and professional journals that circulate through departments, and by conferences and schools that are organized in-house and via the SAIMM and other professional institutions. The importance of these schools cannot be overstated: they combine people and developing technology to the benefit of the industry as a whole.

Jan 1, 1992

By I. E. Lane

Conventional demand management techniques invariably fail to offer optimum control flexibility in an operationally complex gold mining environment. An improved control system for electrical demand management is proposed. The system is designed to provide more effective load scheduling and control strategies by means of a computer aided demand management system (CADMS). The objective of the CADMS is to provide a responsive computational aid and adaptive control system for effective demand management. The system consists of a short term load forecasting module, an interactive load scheduling module, an incentive based electricity cost allocation module and a power management information module.

Jan 1, 1987

By J. D. Smit, K. C. Garner, P. C. van Aswegen

The initial results obtained from the implementation of computer-controlled strategy on the milling circuit are reported. An analysis of these results showed that a peak-power pebble-mill controller on a high throughput hardrock wet-milling circuit reduces the stability of the system. It was concluded that the milling circuit should be regarded as a single system in which the measurement of grinding efficiency, circulating load, product size distribution, and feed rate should minimize the product variance and maximize the feed rate according to the grinding power available. Work is proceeding on such a system.

Jan 1, 1980

The kinetics of cyanide loss were found to be first order under any given set of conditions, allowing rate constants to be easily determined. At room temperature and in the absence of activated carbon, some cyanide is lost by hydrolysis to hydrogen cyanide, but this does not occur to any significant extent at pH values higher than about 10. A higher rate of hydrolysis occurs when air agitation is used. When activated carbon is present, an additional carbon-catalysed oxidation reaction is responsible for a fairly high loss of cyanide. The evidence indicates a reaction mechanism that consumes oxygen and produces cyanate ion. Some of the cyanate thus produced decomposes to form a mixture of ammonia, carbonate, and urea, depending on the solution conditions. Additional cyanide is lost as a result of the adsorption of sodium cyanide by the activated carbon. At high temperatures, an additional hydrolysis reaction, which involves the formation of ammonium formate as an intermediate, occurs an/j is responsible for. a high loss of cyanide, leading ultimately to the formation of ammonia, hydrogen, and carbon dioxide. The presence of activated carbon has no effect on the rate of this reaction.

Jan 1, 1990

Mr R. w.o. Kersten joined the Geological Department of Anglovaal in 1964 after obtaining a B.Sc. Honours degree in Geology at the University of Pretoria. Mr H.G. Mosenthal was educated at Pretoria Boys' High School and the University of the Witwatersrand. He holds a B.Sc. in Mining Engineering and a GDE.

Jan 1, 1985

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By P. Valicek, M. Farren, G. Harrison, G. van den Berg, P. van Dorssen, P. Kramers

Full mechanization of the stoping operation using rockbreaking methods other than blasting has been a target of research for decades because of the considerable payoffs in terms of increased face advance rates, productivity and safety. However, the unavailability of economically viable rock breaking tools has prevented progress so far. This has changed with the invention of activated cutting tools, which achieve significantly reduced operating forces, power consumption and wear compared to non-activated tools and thereby permitted the development and evaluation of the first mining system using this technology. Targets for the mining system were a face advance of 100 metres per month on a double shift basis for a 30 metre long panel and eventually fully automated man-free stoping. The purpose of this paper is to describe the design, development and evaluation of the mining system. This was a major collaborative effort between Anglo Platinum’s Rustenburg Platinum Mines Rustenburg Section — Townlands Business Area, Anglo Platinum’s Research and Development Department within the Mining Technology Division, the inventor of the technology Bechem GmbH, the equipment manufacturers Long-Airdox Ltd and Zollern GmbH, and CSIR Miningtek who managed the project. A structured process was followed during the development to minimize the risks involved in using such leading edge technology. The system was rigorously evaluated to ascertain the economic viability of the method and to collect data for the design of a production system.

Sep 1, 2001

By G. Whittle

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction - primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

Interpretation of Leached Outcrops, by Roland Blanchard. Published by Nevada Bureau of Mines, University of Nevada, Reno, Nevada, 89507, 1968, 188 pages. Price $7.50 (R5.40). This book contains a summary of the author's knowledge of leached outcrops, derived from some 30 years' experience as a geologist operating mainly in the United States of America and Australia. Part 1 of the book provides a comprehensive coverage of the various processes and substances involved in the oxidation of many minerals, under different climatic conditions, to form the final leached products. In Part 2, details are given of the appearance and composition of the oxidation products of the following minerals: pyrite, pyrrhotite, arsenopyrite, cha1copyrite, cha1cocite, bornite, tetrahedrite, oxidized copper minerals, galena, cerussite, sphalerite, molybdenite, chromite, hematite, magnetite, manganite, pyrolusite, calcite, siderite, fluorite, salite and supergene silica. The illustrations, the black and white photographs and the colour plates of oxidation products are of a high standard. The material is presented in a logical order and in terms which are not over-technical; hence it is useful to persons other than trained geologists. Despite the advances in geophysical and geochemical prospecting, the location and interpretation of gossans remains an important method of discovering ore bodies, particularly so since the correct interpretation of a leached material can prevent the fruitless and expensive prospecting of an underlying body of uneconomic concentration. Therefore it is considered that this volume will be a valuable addition to the libraries of universities, exploration companies and geologists. It is of interest to note that the author, who died in 1966, presented a paper, under the same title as this book, to the Chemical, Metallurgical and Mining Society of South Africa in 1939. For this work he was awarded the Society's Gold Medal. W.T.S.

In many practical situations, calculation of the point semivariogram is not necessary. Such a case is analysed in this chapter. The purpose of this analysis is to give a better understanding of the meaning of the mathematical formulae developed in the previous chapters. A similar problem will be studied in Chapter 11, using the point semivariogram.

Jan 1, 1978