Search Documents

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By I. V. Samarasekera, E. B. Hawbolt

A review of recent work being conducted at the university of British Columbia on the modeling of the microstructural evolution during the hot rolling of steel is presented. A mathematical model of heat transfer was developed to describe the thermal field in a slab during rough and finish rolling. The model for rough rolling, discussed in this review, also simulates the growth of oxide scale on the slab surface. To quantify the heat transferred from the slab to the work rolls, instrumented samples of MSI3O4 L stainless steel, 0,05 per cent carbon steel, and 0,05 per cent carbon steel with 0,025 per cent

Jan 1, 1995

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

By K. R. Vost

Most theoretical methods for the prediction of air-temperature gradients in underground airways always assume that the temperature of the entering air either remains constant or has only a slow seasonal variation. Large changes of temperature, caused by variations in atmospheric conditions on the surface, were measured in a fourteen-day period in air entering a horizontal airway. The changes in wet-bulb temperature were damped along the airway less uniformly than the dry-bulb changes; significant variations occurred in the wet-bulb temperature of the air leaving the airway. The damping was .associated with large variations in air-temperature gradients. Other causes of rapid changes In temperature are discussed. These changes must be taken into account in predictions of the frequency with which undesirable conditions can be exceeded at critical points in the ventilation circuit of a mine to allow proper planning of ventilation and refrigeration requirements.

Jan 1, 1977

By J. Björkvall, L. Bååth, D. Malmberg, J. Malm

Microwave technology has for decades been a tool for astronomers to map and understand the complexities of the universe its composition and extent. It is also used on a laboratory scale by spectroscopists to examine properties of atomic and molecular compounds. In this novel work we will introduce microwave technology to be used for the investigation of liquid slag structures. The preliminary results indicate that the alteration of the slag composition could be correlated to the measured microwave refractive index. Investigations have been performed in the Al2O3-CaO-SiO2slag system. Keywords: Microwave technology, slag, structure, liquid, Al2O3-CaO-SiO2

Jan 1, 2004

This report describes the investigational work on the development of a fire-assay method capable of concentrating, in a button of nickel sulphide, all six of the platinum-group metals present in samples of ores, concentrates, and mattes. In the method adopted, the sample is fused with a mixture of sodium carbonate, sodium tetraborate, nickel carbonate, and sulphur. The nickel sulphide formed during fusion collects the noble metals and carries them to the bottom of the crucible. The nickel sulphide button is dissolved, and the noble metals are isolated and determined. The coefficients of variation range between 1,0 and 4,9 per cent for the various platinum-group metals when they are present in concentrations between 0,3 and 75 p.p.m.

Oct 15, 1971

By Page-Shipp. R. J., Elizabeth Harris

A study of the response of South African white gold miners to exposure to dust in their working environment yielded large quantities of dust data. Analysis of this data (presented in summarized form) reveals a variety of interesting relationships, including the shift-long exposure of different occupational groups, the dust levels due to various mining operations, relationships between different dust-measuring procedures and time trends in dust levels during the shift. The statistical probability of contracting silicosis at various levels of exposure to this dust is reported briefly. A new method of using microscope counts to estimate the respirable mass of dust samples is given in an appendix.

By P. F. Sorensen

A simple mathematical model is presented that relates the 'head' developed at the surface of pulp in a tank to the power dissipated by the air in producing it. The value for the head is then used in the calculation of the superficial circulating velocity of the pulp and the area of the overflow, and the product of these two values gives the pumping rate of the pulp. Thus, the superficial circulating velocity, and hence pumping rate of the pulp, are related directly to the flow-rate of the air. This hypothesis was tested with good results in an air-agitated pachuca tank (of 1 m in diameter) fitted with a draught tube. The method can also be used for the prediction of the pumping rates in production-scale vessels.

Jan 1, 1985

By J. D. Flint

A description is given of the extraction of pillars in a seam of coal which normally varies in thickness from 10 feet to 14 feet using conventional trackless mechanised units. By using the pocket and fender method of pillar extraction, the high capital cost of hydraulic supports is eliminated, and a volumetric extraction of 85% to 90% of the seam of coal is possible. This method of mining opens up the possibility of extracting vast tonnages of coal which hitherto would have been left in situ as pillars. The major benefits likely to accrue from this technique are seen as follows: 1. Greater volumetric extraction of the seam; 2. Longer panel life with less frequent transferring of sections; 3. Preservation of our natural resources. The authors deal with the history of this development at Springfield Colliery, discuss the present results and outline the future trends in the light of current experience.

By B. P. Gilbertson

In her wonderful book, 'The Guns of August', historian Barbara Tuchman tells us that the French war plan for 1914 was dedicated entirely to an offensive strategy, not a defensive one. Plan 17, as it was called, concentrated everything on a French advance to the Rhine, leaving the French left virtually unguarded. This strategy could only be justified by the fixed belief that the Germans could not deploy sufficient manpower to extend their invasion around through western Belgium and the low provinces; and this in turn was based on the belief that the Germans would never use reserve troops in the front line. Al evidence to the contrary was ignored. But when the war came, the Germans followed Count Von Schlieffen's plan; they did use reserves in the front line and they did come the long way around on the west. The result- as you know-was a protracted war, with fearful consequences for the rest of our century.

Jan 1, 1994

By J. P. McDonald, P. L. Mattison, J. M. W. Mackenzie

A variety of processing problems in the hydrometallurgical extraction of uranium in the U.S.A. are contrasted with those in South Africa. In U.S. plants, for example, problems are often encountered in the separation of vanadium, molybdenum, and uranium, and in the contamination of the circuit with organic acids. South African plants often experience problems with dissolved silica in the feed, clarification of feeds, and problems associated with synthetic polyelectrolytes. Individual situations are examined, along with the analytical techniques that assist in solving specific problems. Successful approaches that have been applied to mechanical and chemical problems in' uranium solvent-extraction plants are discussed.

Jan 1, 1981

Results from a study undertaken at a Transvaal colliery on the feasibility of undermining an urban development by conventional bord-and-pillar mining operations in the No. 4 Seam of the Highveld Coalfield are discussed. Surface ground vibrations above production sections were measured, analysed, and then compared with well-accepted guidelines so that the expected effects of vibration on inhabitants and surface structures could be determined. The measurement and scaling of ground vibration from blasting are outlined, and the effects on humans and structures are discussed. It is concluded that residential areas can be safely undermined by conventional drilling and blasting techniques provided certain simple guidelines are followed.

Jan 1, 1987

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By D. G. Krige

Recent publications have demonstrated the important role that can be played by a priori information of the grade levels, variability, and spatial patterns in adjacent or nearby areas in improving the quality of grade estimates for virgin or sparsely drilled areas. A research project was therefore conducted involving the collection and analysis of extensive sampling and borehole data from 7 reefs on some 30 Witwatersrand mines. This paper shows that the 'equivalent' log variance for the two-parameter lognormal model provides a good basis for the study and comparison of the levels and behaviour of relative variances. The trends of these against the corresponding log areas were found to form distinctive patterns, which are useful for these purposes. The patterns for the Basal, Vaal, Carbon Leader, and Main Reef Series form a reasonably close group, whereas those for the V.C.R.(particularly where the facies are mixed), B Reef, and Kimberley-Elsburg Reefs (particularly for narrow channel widths) do not always conform. The patterns shown by underground chip samples are also compared with those obtained from borehole cores. It is shown how this information can be used to improve the borehole valuation of new mines and of virgin areas in existing mines.

Jan 1, 1993

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By C. J. Van Niekerk

When gold plant residues are cycloned for producing a coarse product for backfilling the gold and uranium values are upgraded in the backfill product. Gravity concentration, wet high intensity magnetic separation and froth flotation were investigated as first-stage recovery processes to recover these economic values from backfill prior to placement underground. This paper addresses the recovery of values from flotation concentrates and also details the economic feasibility of a treatment route including flotation, followed by roasting of flotation concentrate to liberate gold entrapped in pyrite and reverse gold leaching of the calcine so produced.

Jan 1, 1988

1. Book reviews Quantitative texture analysis, edited by H. ,}. Bunge and C. Esling. Deutsche Gesellschaft fur Metallkunde, 1982. 551 pp. Reviewer: L. 1\'1.Matthews Boundary element methods in solid mechanics by S. L. Crouch and A. M. Starfield. Reviewer: J. A. C. Diering World mineral statistics 1976-1980. Produdion,' exports,' imports, by Institute of Geological Sciences. London, Her Majesty's Stationery Office, 1983. £18.00 Reviewer: R. P. King 2. New publications Canadian mines,. perspective from 1982. Mineral Bulletin MR 197. Supply and Services Canada, Hull, Quebec K1A 059, Canada. Copper' s changing cost structure, by Commodities Research Unit Ltd (31 Mount Pleasant, London, WClX OAD, England). Petrology of metamorphic rocks, by M. Suk. New York, Elsevier, 1983. 320 pp. U.S. $68.00. Applied geomorphology, by H. Th. Verstappen. New York, Elsevier, 1983.442 pp. U.S.$95.75. Tin and its uses, no. 137, by the International Tin Research Institute. Greenford, the Institute (Fraser Road, Greenford, Middlesex UB6 7AQ, England), 1983. 3. New journals Mining Science and Technology, edited by C. 0, Brawner and B. N. Whittaker, is to be published quarterly in one volume per year by Elsevier. Aluminium, published monthly by Aluminium -Verlag GmbH, P.O. Box 1207, D-4oo0 Diisseldorf 1, F.R. Germany. DM 690.00 per annum. Rock mechanics The South African Institute of Mining and Metallurgy is to hold two schools on 'Rock Mechanics in Mine Management' at the University of the Witwatersrand, Johannesburg, from 23rd to 27th January, 1984, and from 30th January to 3rd February, 1984. The Federation of Societies of Professional Engineers The Federation of Societies of Professional Engineers (FSPE) has been a member of the World Federation of Engineering Organisations (W FEO) for many years and has regularly sent delegates to the biennial conference of that organisation. Second progress report by ASRET The Professional Engineers Joint Council was estabislhed in 1960 and initially its main fWlction was to represent the interests of engineers. Explosives technology The Center for Explosives Technology Research (CETR) has been established at the New Mexico Institute of Mining and Technology (Tech) in Socorro, New Mexico. International Tunnelling Association A conference entitled 'Ita Tunnels 1984' will be held in Caracas, Venezuela, from 2nd to 7th June, 1984. Automation The IFAC Symposium on Automation for Mineral Resource Development is to he held in Brisbane (Australia) from 9th to nth July, 1985.

Jan 1, 1983

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

From its early beginnings, shortly after the Witwatersrand gold rush of 1886, Randfontein Estates was planned as a heavyweight operation. The venture was capitalized by J .B. Robinson to the tune of £2 million at time when syndicates were loath to invest £50000 in ventures in and around the new metropolis, Johannesburg, which had sprung up midway along the Witwatersrand. But by then Robinson was a colossus among his contemporaries. Operating as a loner as he had done on the Kimberley diamond fields, where he created his own individual fortune and commanded the sort of respect which, early in his career, led to his election as Mayor of Kimberley. When news of a third gold discovery in the Transvaal (the first two had been in the Pilgrim's Rest and Barberton areas) reached Kimberley, Robinson's pioneering spirit was further stired and he hastened to the new goldfield to stake his claims before his business adversaries- Rhodes, John X. Meriman, Hans Sauer, and Caldecot-could entrench themselves. Once the new Witwatersrand goldfields had been proclaimed, claimpegging started in earnest. But the question was: where to start? Diamond men al, not one of the financiers had any knowledge of the geology of the gold-bearing formations.

Jan 1, 1989

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988