Search Documents

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By A. Bain

The use of plastics in the coal mining industry is making slow progress whereas these materials could make a greater contribution to safety, to a reduction of working costs and to the higher productivity of mine workers. Possibly the reluctance to experiment with the new material of our age is due to the low profit margin of coal mining. This note has been prepared to present a brief survey of what has been done in the last few years and to mention some of the investigations the author has made and is making in an attempt to develop more use of plastics in the industry. Some of the plastics used on the mines have taken their place in the industry in the same manner that they are used in everyday life while others have been introduced because there has been a need for them. New uses and applications are being developed and these are the ones that are most interesting. The plastic that is specially developed to give the maximum benefit and not the one that is a modification of some other everyday product is the next development in the field. Many manufacturers are keen to promote such investigation but are not aware of the problems the mines wish to solve and therefore it is only through management itself that this development can be carried out. This note deals with plastic material under three headings: (a) Plastic as the superior material, and briefly describes how plastic has replaced a few major items which are better when made from plastic. (b) Plastics of necessity, being a short summary of how plastics had to be introduced because of laws and conditions making it a necessity. (c) Development of new ideas, being briefly some of the ideas being developed overseas and some of the ideas being tried by the author. Plastic items in common use such as in housing, electric cables, laboratory equipment, awnings, nylon bearings, locomotive brake linings, etc. being well known are not discussed. PLASTIC AS THE SUPERIOR MATERIAL Plastic belting underground Following a fire in a belt road in England resulting in the deaths of many workers, and subsequently a fire accompanied by fatalities in a belt road in a mine in this country, a law was introduced which states that only flameproof belting is to be used underground. This ruling forced the mines to use P.V.A. belting as no other was available. This belting has non-inflammable characteristics that are superior to rubber. Due to the high tension on long-distance belts used today the need for stronger belting material called for something better than cotton and the answer to this was nylon. Nylon also has the ability to withstand dry-rot which reduces the life of a belt very quickly.

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

By J. A. L. Napier

By use of a functional model of capital expenditure developed earlier, a prototype cash-flow model is formulated as a basis for the investigation of the economic consequences when the production rate of a mine is manipulated as fundamental design variable. The optimum production capacities that maximize the common economic criteria of net present value, present-value ratio, and wealth growth rate are determined. It is shown that these choices depend certain key groupings of the economic parameters, and that they have a fixed interrelationship. The basic cash-flow model is extended further to include the effects of a constrained rate of production buildup and the imposition of State taxation on generated income. An approximation to the initial tax-free period of a new mining venture is developed, and, by use of these results, the optimum choice of production level is analysed when both the buildup rate is constrained and tax is imposed. This extended model permits a comparison between the performance of existing mines and the predicted theoretical production levels for these mines.

Jan 1, 1981

By S. Gqebe, A. Lewis, M. Rodriguez-Pascual

"Gravitational sedimentation of suspensions in various precipitation processes is hindered by colloidal stability. This is due to the high surface charge of the suspension and results in strong attraction/interaction between the ions on the particle surface and counter-ions in solution. Moreover, this strong interaction results in a charge build-up that renders the suspension stable. In order to induce gravitational sedimentation of these particles, a redistribution of ions close to the particle surface is required. We therefore sought to redistribute ions close to the particle surface by applying a magnetic field. This results in the reduction of interparticle electrostatic repulsive forces and a subsequent increase in the zeta potential of a suspension. For the purpose of this study, a copper sulphide suspension was used. Copper sulphide particles were exposed to a range of field strengths for set exposure times and their zeta potential was measured before and after exposure. All particles had an initial zeta potential value equal to or less than –40 mV prior to magnetic field exposure. A significant increase in zeta potential was observed, with values reaching a maximum of –16.5 mV when exposed to a 2 T field strength for 40 minutes. This is due to Lorentz ion shifts resulting from the Lorentz force exerted by the magnetic field on the particle surface. IntroductionMetal sulphide precipitation is a process for treating industrial waste streams with high residual concentration of mixed metal ions and acid mine drainage. This process has been reported to achieve higher metal removal compared with the industrially prevalent lime precipitation, due to the sparingly soluble nature of the metal sulphide precipitates formed. However, precipitation is governed by high levels of supersaturation which favour the formation of fine particles (Lewis, 2010). Consequently, some of the metal sulphide fines formed exhibit slow settling dynamics and thus tend to remain suspended in solution."

Jan 1, 2016

By A. L. Bleloch, A. M. Starfield

This paper is concerned with heat flow in the plane of a typical cross-section of a deep underground airway. A new algorithm, called the quasi-steady method, is presented for the calculation of rock temperatures in that plane. The algorithm is used in the computation of heat and moisture transfer rates from the rock to the ventilating air for an airway that is wet on part of its circumference and dry elsewhere. The speed and accuracy of the new method are demonstrated on a microcomputer, and it is argued that this method offers a considerably more versatile and physically meaningful alternative to previous methods for the prediction of increases in air temperature along mine airways. The algorithm is also used to explore the concept of a uniformly wet airway that is equivalent to a partly wet airway in terms of its effect on the ventilating air. The concept is shown to be reasonable, but more complex than one might have anticipated. Finally, several useful extensions and applications of the new method are suggested.

Jan 1, 1983

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

By I. J. Barker, D. A. Vetter, G. A. Turner

The modeling of the uranium-leaching process, and the logging of data from a plant for the evaluation of the model, are reported. A phenomenological approach was adopted in the development of the model. A set of eight chemical reactions was chosen to represent the complex chemistry of the process, and kinetic expressions for these reactions were incorporated in differential equations representing mass and energy balances. These equations were coded in FORTRAN to form a program that simulated the process, and that allowed averaged and continuous data from the plant to be compared with the model. This allowed the model to be 'tuned', and to reveal a number of minor

Jan 1, 1989

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

Tests were carried out in a Hallimond microflotation cell and a Denver D12 cell on typical residue material from a gold mine in the Orange Free State (South Africa), in which 50 per cent of the kerogen was larger than 100 µm in size. Although kerogen is naturally hydrophobic, the observed unexpectedly poor flotation reponse may be due to occlusion of the kerogen by a slime coating and subsequent depression of the slime by guar gums. The recovery of gold from samples spiked with kerogen increased, with no significant reduction in grades, when a petroleum-based collector and tetrasodiumpyrophosphate (a dispersant) were used.

Jan 1, 1985

By J. J. van Vuuren

Pipe-stick support in deep-level gold mines is first described and illustrated, a pipe-stick being a mine pole trimmed to the required size and sleeved by a pipe. An account is then given of an investigation into this form of support that involved load-compression tests in a 1000-ton press, tests in a rapid loading machine simulating rock-burst conditions, a study of the load-compression behaviour of pipesticks installed underground, and a cost evaluation. Pipe-stick support was found to be very effective on the face and to cost less than conventional matpacks.

Jan 1, 1979

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

1. Book reviews Phosphate rock, a bibliography of world resources. London, Mining Journal Books Limited, 1984. £10 (surface mail), £12.25 (airmail). Reviewer: P.Le. Grubb Ok Tedi, by William S. Pintz. London, Mining Journal Books Limited, 1984. 206 pp. £19 (surface mail), £22.25 (airmail). Reviewer: R.P. Plewman 2. Publications of the Canadian Mineral Policy Sector Lime by D.H. Stonehouse. 5 pp. Phosphates by G.S. Barry. 9 pp. Statistical summary of the mineral industry in Canada. 77 tables. Talc by M. Prud'homme. 6 pp. Zirconium by M.A. Boucher. 6 pp. Cement by D.H. Stonehouse. 13 pp. Gypsum and anhydrite by D.H. Stonehouse. 7 pp. Regional review by T.M. Buch. 12pp. SaltbyG.S. Barry. 7pp. Silicon, ferrosilicon and silicon carbide by D.G. Law-West. 6pp. SulphurbyB.W. Boyd. 9pp. Mineral Report 31. Canadian Minerals Yearbook 1981. Available from the above address at $40.75 per copy. 3. Mintek reports Report M18D The recovery of pyrite and gold from acid-leach residues from the Merriespruit Gold Mine. (First issued Feb. 1982; reissued Mar. 1984). Report M2OD The separation of ore from Cooke into high- and lowgrade fractions. (First issued Feb. 1982; reissued Mar. 1984). Report M33D Explanatory tests on the reduction of the sulphur content of sponge iron. (First issued Apr. 1982; reissued Mar. 1984). Report M43D Beneficiation tests on andalusite-bearing shales from a farm near Thabazimbi. (First issued Aug. 1982; reissuedMar. 1984). Report M129 The determination of tin, niobium, and tantalum in pegmatite by X-ray-fluorescence spectrometry. ReportM131 The determination of copper and nickel in iron- and chromium-bearing materials by a pressed-powder technique and X-ray-fluorescence spectrometry. Report M135 The installation of a 100 kV A plasma furnace at Mintek. The selection and installation of a 100 kV A a.c. plasma Report M136 The determination of gold in activated charcoal by use of a loose-powder technique and X-ray-fluorescence spectrometry. Report M140 The effect of physical and chemical factors on the corrosivity of a synthetic mine water.

Jan 1, 1984

By N. Watson

Historically the insurance industry's involvement in any project has been relatively late in the process. Often it was a case of the last item to be ticked off the checklist has been to ensure that the insurance is in place. However, in more recent times insurers have imposed more restrictions on the cover they are prepared to provide, which has in some cases necessitated a change in the contracting structure to accommodate the insurance policy(ies). In addition, changing contractual practices have changed the allocation of risk between the various parties involved. This calls for a more proactive approach to the design and implementation of an insurance program for both the construction and operational phases of any resource project. This paper explores how a risk managed approach to the design and implementation of an insurance program for a resource project can align itself with current management approaches to project development. From the authors' experience, this approach is best adopted early on in the project (often in conjunction with the bankable feasibility study) and follows AZ/NZS4360 to objectively examine and compare a wide range of risk exposures of the project in a time-effective manner across the following areas: ? personnel; ? environment; ? general management; ? compliance - legislation, systems, protocols; ? asset management; ? change management; ? financial impacts to the organisation; ? products/services; ? service delivery; and ? technology. Having identified and then analysed the risk exposures according to common consequence and likelihood ratings the next step is to develop a risk map of all considered exposures. The true value of this approach lies in the development and implementation of a risk treatment plan for identified exposures where the exposure is unacceptable. The plans will lead to the optimal solution to the appropriate risk prevention, risk mitigation and risk transfer options available. This paper also examines other benefits to the project that may arise from adopting a risk managed approach in addition to the ability to design an insurance program which recognises the exposures and the ability of the organisation (and other project parties) to retain risk.

Jan 1, 2007

1. New books Extractionmetallurgy'81. London, Institution of Mining and Metallurgy, 1981. 441 pp. $40. Structures and properties of engineering alloys, by W. F. Smith. London, McGraw-Hill, 1981. 512 pp. R89,65. Rock and mineral analysis, by W. M. Johnson and J. A. Maxwell (editors). 2nd ed. New York, Wiley, 1981. 424 pp. $40. Mining methods and equipment, by Mining Information Services. London, McGraw-Hill, 1981. 218 pp. International directory of acronyms in library, information and computer sciences, by P. M. Vaillancourt. New York, Bowker Publishing Co., 1980.516 pp. 2. New journals Trends in analytical chemistry (TRAC), Amsterdam, Elsevier, 12 issues per year. Subs. for Volume I (16 issues) D.H 95.50. Engineering management international, Amsterdam, Elsevier, 4 issues per year. V.S. $32.50, D.H. 70.00. 3. Mineral policy sector publications Mineral Bulletin MR 188. Vanadium: an imported mineral commodity. $3.60. Mineral Bulletin MR 190. Canadian mines: 1980 perspective. $3.00. Canadian mineral survey 1980, by the staff of Mineral Policy and Energy Sectors. $1.00. 4. NIM reports Report 2090 Observations made during the dig-out of a 48 MV A ferrochromium furnace. Report 2110 The investigation of a fracture on one side of a skip bridle in a mine shaft. Report 2111 Pilot-plant tests for the recovery of chromite and the noble metals from the UG-2 Reef at Maandagshoek. Report 2112 The behaviour of UG-2 chromite concentrates during smeUing. Report 2113 M uUivariable control of a milling circuit at East Driefontein Gold Mine. Report 2115 Estimation of material variation in powdered materials Report 2116 Optimum operation of a direct-reading spectrometer with excitation by a 5 kW inductively coupled plasma torch. Report 2121 Five robust indicators of central value. Report 2124 The direct determination, by differential pulse anodicstripping voUammetry at the thin mercury-film electrode,of cadmium, lead, and copper. Report 2127 The preparation of a reference material of South African zirconium concentrate from Richards Bay. Report 2128 The determination, by differential pulse anodic-stripping voltammetry at the thin mercury-film electrode, of cadmium and thallium in six NIMROC reference materials Report 2130 The organizing of conferences. Research grant The Board of Directors of International Precious Metals Institute in conjunction with Gemini Industries, Inc., a California-based refiner of precious metals, recently announced a Gemini Research Grant of $3000 will be awarded annually to a graduate student who is pursuing studies in metallurgy, chemical processes as it pertains to precious metals, or materials sciences, and who is performing or planning research studies in the precious metals. Accidents and diseases The Third International Colloquium for the Prevention of Occupational Accidents and Diseases in the Iron and Metal Industry is to be held on 15th and 16th June, 1982, in Palma de Mallorca, Spain.

Jan 1, 1981

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

Professor R.F. Sandenbergh matriculated at Germiston Afrikaans High School, and then he obtained the degrees of B.Eng. (Chem.) in 1972, M.Eng. (Chem.) in 1975, and D.Eng. (Met.) in 1983-all from the University of Pretoria. Mr J.A.D. Britz matriculated in 1958 at the Roodepoort Hoerskool, and joined the mining industry in 1959 as a student mine official at the Rand Mines Training Centre. Mr J.A. Cruise matriculated at Durban High School and joined Union Corporation as a Learner Official in 1962. He was awarded a scholarship to read for B.Sc. and M.Sc. degrees in mining engineering at the University of the Witwatersrand

Jan 1, 1990

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987