Search Documents

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

By O. A. W. Strydom, J. C. M. Wethmar, P. R. Jochens, D. D. Howat

Liquidus temperatures in the Cr-Fe-Si system in the composition range representative of ferrochromium-silicide produced in South Africa J. C. M. Wethmar, B.Se. (Eng.) Rand D. D. Howat,U B.Se. (Glas.), Ph.D.. F.I.M. P. R. Joehens, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. O. A. W. Strydom, M.Sc., Ph.D. Alloys in the composition range of chromium, 20 to 50 per cent, iron, 10 to 30 per cent, and silicon, 25 to 55 per cent, were subjected to both differential thermal analysis and the classical quench method so that the liquidus temperatures of ferrochromium-silicide alloys could be determined. The results are presented as liquidus curves on pseudo-binary sections at various ratios of chromium to iron and as liquidus isotherms in the ternary section.

By R. P. Plasket, D. A. Ireland

Ancillary smelter operations and sulphuric acid manufacture at Impala Platinum Limited by R. P. PLASKET. Pr. Eng.. M.Sc. (Chem. Tech.). Natal (Fellow) and D. A. IRELAND. Pr. Eng.. B.Sc. (Chem. Tech.). Natal (Member) The de-watering, spray drying, and converter operations at Impala are described, aspects that may be new to the minerals industry in South Africa being elaborated. Air-pollution control necessitated the installation of a sulphuric acid plant to limit the emission of sulphur dioxide to the atmosphere. Closer control of the smelting and converting operations was required for successful operation of the acid plant on the inherently Iow and varied concentration of feed gas from converter blowing. Approximately 82 per cent of the sulphur entering the smelter is converted to sulphur dioxide, of which 67 per cent is fed into the sulphuric acid plant.

Jan 8, 1976

By I. D. Wood

Deposition of gold-bearing deposits in the Witwatersrand Basin was controlled by hydraulic processes. These resulted in the formation of independent sedimentological facies areas having different statistics and semivariograms. Consequently, when there are indications that data are a mixture of statistical populations, it is important to decompose them into statistical subpopulations and analyse these independently. However, in the case of actual mining, physical position and extent of sub- populations are important and, as a consequence, any decomposition of data must take space into account if it is to be of use. An algorithm for the spatial decomposition of data into its sub-populations is described and is applied to real data taken from the Witwatersrand. Two distinct areas with completely different geostatistical parameters were revealed.

Jan 1, 1987

By D. I. Nicol

An assessment is made of the possible scope for the use of activated charcoal as the solid adsorbent in an upflow fluidized-bed contactor, and a pilot-plant programme for the recovery of low concentrations of dissolved gold in this contactor is described. It was found possible to produce an effluent that contains less than 0,01 p.p.m. of dissolved gold.

Jan 1, 1997

By D. A. Holtum

On Tuesday, 10th November, 1987, The South African Institute of Mining and Metallurgy held a colloquium attended by some 120 delegates on 'On-Stream Analysis' at Mintek, Randburg. Mr John Moore, Consulting Metallurgist of Anglo American Corporation of South Africa Ltd, introduced Mr Gene Fivaz, the President- Elect of the SAIMM, who read an address by Mr B.C. Alberts, the current President. Mr Alberts was unable to attend the Colloquium owing to urgent business overseas. Opening The opening address emphasized the important role of minerals in the South African economy. In particular, it was noted that 20 per cent of the work force were employed in the minerals industry or associated industries. In recent years, production costs had risen as a result of inflation, and sanctions had had some effect on the exportation of minerals. Thus, there was continuing pressure on the industry to improve recoveries and increase efficiency.

Jan 1, 1988

By R. M. S. Falcon, L. M. Falcon

The prediction of the mechanical behaviour of South African coal on the basis of current proximate and other chemical parameters gives rise to problems, and the use of ultimate analyses and inferred maceral and rank analyses, although it has improved the situation to some extent, is still not satisfactory. In an attempt to reach a new level of understanding, this paper gives an in-depth review of the fundamental petrographic characteristics of coal and compares these parameters with the main types of mechanical performance. A two-tiered system of primary and secondary parameters is proposed for the prediction of coal behaviour. The primary or inherent parameters include rank and organic composition. The secondary or extraneous factors include such parameters as mineral mater, cracks or cleats, degree of oxidation, and size. In addition, an explanation is offered of several anomalous behavioural conditions in some South African coals.

Jan 1, 1987

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.

By A. J. Vietti

"Drought conditions and the possible lack of sufficient raw water supply are a constant reminder to the Southern African diamond miner of the need to minimize raw (new) water input while maintaining or expanding mine throughput.Since water input volume is directly related to water output (loss) volume, mainly to the tailings, it is obviously beneficial to dewater the tailings as much as possible. However, this may not always be as easily achieved as first thought. Owing to the unique mineralogy of each kimberlite deposit and the unique chemical profile of each raw water source, dewatering of the slurry is not a standard process that can be applied equally across the entire diamond industry.This paper presents a first-step strategy that kimberlite diamond mine operators should consider and apply to meet and exceed their watersaving targets. Introduction A common metric for measuring water use efficiency in a metallurgical plant is the amount of raw water used per ton of head feed treated (m3/t). The metric includes all water recycled from the dewatering process and from the tailings storage facility (TSF), and the only inputs are tons of ROM ore and cubic metres of raw water make-up to replace water lost to evaporation, seepage, and lock-up at the TSF (Figure 1).The volume of new raw water available to the process is not unlimited and a maximum monthly allowance is typically set during the mine permitting process. Consequently, if the volume of water lost exceeds the volume of new water available or alternatively, in times of drought where the allowable volume is unavailable, the plant has no other option but to reduce throughput.However, if the plant operator is able reduce the volume of water lost to the TSF, the plant will have additional capacity to either increase tonnage throughput or sustain nameplate capacity during periods of severe drought. The obvious conclusion, therefore, is to reduce the volume of water lost to the tailings by improving the efficiency of the dewatering process (typically gravity thickening) simply by increasing the density of the tailings being discharged. In practice, however, the unique mineralogy of each kimberlite deposit and the chemical profile of the raw water source used imply that at some mine sites, solid/liquid separation (or settling) of tailings slurries at the dewatering process is more easily achieved than at others. In these cases, simple practical steps such as firstly improving the flocculant reagent make-up and dosing control, and secondly focusing on thickener discharge control, are the only requirements for enhancing water recovery at the dewatering circuit. At other mine sites however, solid/liquid separation of the tailings may not be achieved at all, in which case efforts to increase water recovery by improving reagent dosage and thickener control would be fruitless unless the colloidal properties of the thickener feed slurry are modified."

Feb 1, 2019

By B. P. Christos

The improved rate of stope-face advance at Buffelsfontein Gold Mining Company Limited by B. P. CHRISTOS (Associate) To achieve a higher rate of stope-face advance. it was necessary to examine al.1aspects of the stoping operation, to identify bottlenecks, and to eliminate them or reduce their effect. The cleaning cycle was fund to be the most significant bottleneck. and this problem was aggravated by long panel lengths. under-capacity winches In strike gullies. and excessively long strike scraping distances.

Jan 12, 1975

Book news 1. Book reviews ? Prospecting in areas of desert terrain. London, The Institution of Mining and Metallurgy, 1985. 283 pp. £28 (members £25,20). Reviewer: J.S. Mostert This publication records the proceedings of a con¬ference convened to deal exclusively with prospecting in areas of desert terrain. The meeting, organized jointly by The Institution of Mining and Metallurgy (London) and the Ministry of Energy and Mines, Morocco, was held in Rabat from 14th to 17th April, 1985, and generated considerable international interest. Exploration cam¬paigns and case studies of successful discoveries in the desert areas of more than 14 lands are described. Since large areas of South Africa, Botswana, and Namibia are characterized by and and semi-arid terrains, this publication should be of considerable interest to explorationists and mining engineers engaged in the search for and development of mineral deposits in southern Africa. The fact that the desert terrains of southern Africa are host to a number of important base-metal (Aggeneys, Gamsberg, Prieska, and O'Okiep) and diamond deposits (Orapa, Jwaneng) has ensured continued interest in these areas from the viewpoints of exploration and mining.

Jan 1, 1985

By L. Woollacott, R. P. King

This paper presents data collected from full-scale plants in order to verify the predictions of a new simulator of CIP or CL operations. Good agreement was found between the experimental data and the simulator predictions. The simulator is able to predict the effects of many of the complex operating phenomena in GIP and CL plants that previous simulation techniques could not describe. This is illustrated by predictions of how factors, such as the manner of carbon transfer, concurrent leaching, and gold loading on eluted carbon, can affect the performance of an adsorption plant.

Jan 1, 1990

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By J. P. Kirsch

This paper sets out to clearly identify all elements that make up an effective furnace feed system. These are outlined and the more common types of technology are listed. These technologies all play an important role in the final delivery of all feed materials to the furnace.

Jan 1, 2008

By P. Geldenhuys, D. J. C. Taylor, D. C. Page

This paper gives a technical review of the history, occurrence, mining, and metallurgy of iron in South Africa. The reserves of iron ore worldwide and in South Africa are reviewed, and potential new developments In the iron-and-steel industry in South Africa are examined. The paper concludes that the exploitation of lower-grade iron deposits will probably supplement the reserves of high-grade hematite ore in the distant future, and that, accepting this scenario. South Africa will be well placed to provide iron ore for its expected internal steel requirements, as well as supplying quality Iron ore for the export market.

Jan 1, 1988

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different methods of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approaches. This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

By A. Koursaris, H. M. Friede, A. A. Hejja

The features of smelting slags from South African prehistoric sites and of related cinder material are described. Chemical analyses of twelve slag samples found in the Transvaal, Swaziland, and Botswana are reported and discussed. An attempt is made to establish a relationship between these slags and the ores collected at the Early Iron Age site of Broederstroom, which date between AD 350 and AD 600. The liquidus temperatures of29 slags were determined by the use oh hot-stage microscope. The major mineral phases of 16 slags were identified by X-ray diffraction and microscopic examination. It appears that the slags investigated were formed at temperatures below 1250°C or - in some cases - at temperatures only marginally in excess of 1250°C.

Jan 1, 1982