Search Documents

By B. M. Munyungano

Rössing Uranium Mine operates a recovery circuit with continuous ion exchange followed by solvent extraction. Serious organic degradation problems were encountered during 1985/6, 2000 and 2005 in the solvent extraction plant. The preferential loss of the tertiary amine extractant was observed during the above-mentioned period. Previous investigations revealed that the tertiary amine was breaking down to nitrosamine, which cannot take part in the exchange reaction with U3O8. A reduction in the redox potential of the solvent extraction plant feed to below 500 mV halted this preferential loss. A lot of effort has been made to try and understand the actual mechanism for nitrosamine formation. Current understanding for the degradation is that formation is due to high nitrates on the strip side of the circuit emanating from nitrates from the precipitation process using ammonia. It is the current belief that pH lower than 3.7 on the strip side results in loading of nitrates onto the solvent. If oxidizing conditions prevail on the extraction side of the solvent extraction circuit, the tertiary alamine will then degrade into nitrosamine. This phenomenon is yet to be established and verified. It has, however, been established that the above process is brought about the following conditions ?High redox potential greater than 550 mV predominately caused by a high Fe3+/Fe2+ratio (4:1) ?Perception that if Fe2+<0.5 g/lit will contribute to high redox ?High concentrations of NO-3 in the conc eluate (feed to SX)/ammonium sulphate (NO-3> 4 g/l based on historic values) ?Presence of Mo as a catalyst ?Tests also have proved that the presence of nitrous acid in a concentration of 1 g/lat 550 mV leads to formation of nitrosamines from alamine.

Jan 1, 2007

By L. A. Sandham

Environmental impact assessment (EIA) in South Africa is administered by the Department of Minerals and Energy (DME) for the mining industry, and the Department of Environmental Affairs and Tourism (DEAT) for all other sectors. Thus far, EIA research has focused on the process under the auspices of DEAT but none has focused on the EIA process that has been mandatory in the South African mining industry since 2004. Using the Lee and Colley(Lee et al.13) review package as a basis, a review model specifically tailored to the needs of the mining industry was applied to review the quality of a sample of 20 environmental impact reports (EIRs)approved by the DME. Results reveal that 85% of the EIRs are of a satisfactory quality. Presentational and descriptive components generally achieved higher quality grades than the analytical components such as impact magnitude and alternatives. The results show that in spite of some areas of weakness, and in spite of being conducted in terms of different legislation, EIR quality in the mining sectors appears to conform to the overall standard of quality of EIRs in other sectors in South Africa, and is also on a par with quality abroad. Hence, despite the criticism that DME is usurping the role of DEAT, it is concluded that EIRs of comparable standard are being produced, and that the quality of EIRs in the mining sector do not provide supporting evidence for this criticism. However, EIR quality is only a single aspect of EIA effectiveness, others including action and implementation of EIA proposals and mitigation measures.

Jan 1, 2008

By L. A. Vermeulen, D. D. Howat

A study was made of the performance of a rod mil operating without liter bars and with different arrangements of liter bars in the lining. . The results show that striking improvements in performance, increased throughput, and reduced consumption of liner metal and electrical energy can be obtained by a change in the geometry of the liter-bar arrangements within a mil. Rod mils of equal size fitted with the same arrangement of liter bars but operating at different speeds presented apparent anomalies in the relative consumption efficiency of electrical energy for the production of material smaller than 75 µ m. Marked savings in the consumption of liner metal were achieved by the use of an arrangement of alternating lines of higher and lower liter bars. A study of the relative performances of two large tube mils showed that the use of liter bars in one of the mils resulted in a marked reduction in the consumption of liner metal and electrical energy per ton of material smaller than 75 µ m in the product.

Jan 1, 1986

By D. S. Loubser

The technique of backfilling in the gold mining industry is dependent on the dewatering of slurry to form a solid support system. In many cases flocculants are added to the slurry to increase the rate of dewatering. To ensure that a stable support is obtained it is important that the chemistry, application and limitations of these flocculant additives are understood. Flocculant additives have to be added at a point where minimum shear will occur. (Shear occurs when a flocculant is exposed to excess energy resulting in breakdown, of the floc.) To ensure that optimum results are obtained it is important that personnel involved are trained to use the flocculant additives and dosing equipment correctly.

Jan 1, 1988

By H. Wagner

The discovery of the gold-rich Main Reef Group of reefs on the farm Langlaagte in 1886 marked the opening of the richest and most extensive goldfield in history. Mining of the narrow reefs progressed from the outcrops to more than 3,5 km, and has made South Africa the foremost mining country in the world. Changes in the political and socio-economic climate create a new challenge to the gold-mining industry. The most significant of these is the emergence of Black trade unions, with their demands for higher wages, improved safety, job advancement, and abolition of discriminatory legislation. Industrial conflicts on gold mines have risen significantly in the past ten years, and are likely to continue in the future, although the causes of these conflicts may change. Events largely outside the control of the gold-mining industry, such as the improved dollar price for gold and the depreciation of the value of the rand relative to major currencies, have enabled the industry to meet the demands for higher wages and to narrow the wage gap. However, labour productivities have improved insignificantly and are a cause of major concern for the future development of the industry. Continued pressure in the industrial-relations area, the inflation of working costs, and the extension of mining operations to greater depths and more difficult areas create major challenges to mine managements and mining engineers. Significant improvements in mining technology, environmental control, and safety will have to be made to ensure the long-term survival of the industry. The unavoidable introduction in deep gold mines of mechanization on a larger scale to meet the requirements of higher labour productivities and a better and safer underground environment will have a major impact on the cost and management structure of these mines. Engineering will assume a more important role on deep gold mil1es, and management styles and structures will have to be adapted to accommodate these changes. The supply of suitably qualified engineers, technicians, and artisans will be a crucial factor controlling the rate of technological change. The industry is well-geared through its Group system to meet these challenges, and to benefit from the experience gained in the operation of highly mechanized mines. However, changes take time to implement and there is very little time left.

Jan 1, 1986

By R. S. J. Du Toit

SYNOPSIS This paper is based on a thesis dealing with the problem of basing the current rate at which money is collected from mine owners to pay compensation for pneumoconiosis in the future, on the current dust hazard on mines. The certification of pneumoconiotics and the incidence of pneumoconiosis are discussed against the background of existing legal provision for collecting funds for compensation. The various pneumoconiosis indices are considered. In the data analyzed, the only pneumoconiosis index common to a number of classes of mines is the time it takes to develop pneumoconiosis. Sets of dust indices and pneumoconiosis indices are computed. Expressions are derived for the time it takes to develop pneumoconiosis as a function of the dust hazard, and for the collection of funds as a function of the time available for collection. From these two expressions follows an expression for the rate of collecting funds as a function of the dust hazard.

By B. Sergeant

Any study of the contentious subject of nationalization can ultimately be reduced to a sombre analysis of the simultaneous, and very different, interests of capital, labour, and government. Each of these interests attempts to maximize its objectives, subject to checks and balances provided, in an ideal system, by a country&apos;s executive government, legislature, and judiciary. Where even one of the three interests goes out of control, the consequences can be disastrous. The case histories show that when this occurs, the most common culprit is government, or its proxy, such as a dictator. At the other extreme, the case studies indicate that the optimum outcome occurs when capital, labour, and government are &apos;ring fenced&apos; from each other: each enjoys its rights, but is also subject to duties. &apos;Conflicts of interest&apos; between the three entities are ideally avoided to the maximum possible extent. The case studies include several salient instances from both the DRC (Gécamines, La Générale des Carrières et des Mines) and Zambia, along with Ghana and Chile. Further instances are examined in South Africa (gold), India (Coal of India), Brazil (Petrobras), Venezuela (Petróleos de Venezuela), Sweden (Luossavaara-Kiirunavaara Aktiebolag), Mauritania (Société Nationale Industrielle et Minière), Norway (Norsk Hydro), Botswana (Debswana), and Namibia (Namdeb). The article concludes broadly that South Africa&apos;s minerals sector is not ready for nationalization.

Jan 1, 2013

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years&apos; duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00 (country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years&apos; duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the persmission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute&apos;s financial year in which the attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, p.a. Box 1183, Johannesburg.

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By M. Thurston

This case study shows that for a set of lognormal data with a low coefficient of variation the semi-variogram of the logs has almost the same shape as the semi-variogram of the raw data. This means that the variogram of the logs, which is numerically more stable, can be used to krige the raw data. This technique is tested on samples from a sedimentary gold deposit and the results compared to those obtained from ordinary and simple lognormal kriging.

Jan 1, 1987

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMC&apos;s (now BHP Billiton&apos;s) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

By M. Pötsch, W. Schubert, A. Goricki

Geological and geotechnical data are essential for the design of tunnels. To determine the rock mass behavior and the support of a planned tunnel excavation a consistent method for rock mass characterization and excavation and support determination has been developed. Probabilistic data processing with analytical methods is used for the quantification of the procedure and allows an evaluation of the applicability and the technical risk of different excavation and support methods. The sensitivity of the procedure on selected input parameters is highlighted in a parametric study. Finally an application of the procedure illustrates the use of the described method of probabilistic excavation and support determination for tunnels. Des données géologiques et géotechniques sont décisives pour la planification d’un tunnel. Pour la détermination du comportement des strates, le choix du soutènement et de la méthode de progression une description compréhensible de la montagne a été développée. À l&apos;aide d&apos;un traitement de données probabiliste, la procédure proposée est transposée quantitative sur une base de méthodes analytiques. De cette manière l&apos;évaluation des méthodes de construction et la détermination du risque technique deviennent possibles. La sensitivité de la procédure de différents paramètres d&apos;entrée est représentée dans une étude de paramètre. Pour finir, l&apos;application de la procédure décrite est montrée à l’aide d&apos;un cas pratique. Geologische und geotechnische Daten sind entscheidend für die Planung von Tunnels. Für die Ermittlung des Gebirgsverhaltens und der Festlegung von Ausbruch und Stützung wurde ein nachvollziehbarer Ablauf der Gebirgsbeschreibung entwickelt. Mit Hilfe von probabilistischer Datenverarbeitung auf Grundlage analytischer Methoden wird die vorgeschlagene Prozedur quantiativ umgesetzt. Dadurch werden die Bewertung von Baumethoden und die Ermittlung des technischen Risikos ermöglicht. Die Sensitivität des Verfahrens von einzelnen Eingangsparametern wird in einer Parameterstudie dargestellt. Abschließend wird anhand eines Beispiels die Anwendung des beschriebenen Verfahrens gezeigt.

Jan 1, 2003

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987

By L. A. Cramer

There are a couple of dozen junior platinum mining companies coming into existence in Southern African and most intend to mine, concentrate the PGM?s in a flotation product and sell the concentrate to one of the major producers in South Africa. The price they will receive for their product and hence the return they achieve for their investment will depend upon the large number of factors that influence the market for such a product. Unfortunately the number of buyers is severely limited as it is dominated by the two major local producers, Impala Platinum and Anglo Platinum. Furthermore the current smelting technology has limited capacity for UG2 concentrates and high nickel concentrates will quickly fill any available base metal refining capacity. Few if any overseas buyers can compete for the bulky flotation concentrate produced. This paper will explore those factors such as metal recoveries, metal prices, operating costs, capacity constraints, deleterious elements, transport issues, metal premiums and discounts that are in play, types of flotation concentrates, processing capital costs, PGM grades, etc and their impact up on what smelters and refiners might be prepared to pay for such PGM concentrates. Ultimately simple graphs and equations can be developed for probably payment terms for such concentrates. Those who negotiate well will move to the higher return section of the envelope and those who use the concentrator facilities to produce the most saleable combination of flotation concentrates will enhance their returns. A deep and firm understanding of the issues surrounding this market is necessary in order to negotiate the best possible price for the seller.

Jan 1, 2008

By C. F. Vos, J. D. Miller, J. C. Davidtz

"This work presents the potential for improving the flotation recovery of slow-floating sulphide minerals with the use of starvation dosages of a normal dodecyl (n-C12) trithiocarbonate (TTC) co-collector, together with a sodium isobutyl xanthate (SiBX) and dithiophosphate (DTP) collector mixture.At potentials below –150 mV (SHE), addition of nC12-TTC with SiBX improves the hydrophobicity of pyrrhotite, yielding captive bubble contact angles greater than those measured for SiBX or nC12-TTC alone, suggesting a low potential synergistic effect. This synergistic effect is further studied using Fourier transform infrared (FTIR) spectroscopy, the results indicating an increase in the surface concentration of the collector species when in a mixture. Thus, nC12-TTC with SiBX may act as an immobile surface anchor to which SiBX/SiBX2 molecules bond, increasing the localized concentration of collector species.Bench-scale flotation tests using mixtures of SiBX/DTP/nC12-TTC on a platinum group element (PGE)-bearing ore from the Bushveld Complex in South Africa confirm an improved metallurgical performance at very low substitutions (approx. 5 molar per cent) of SiBX. The improved recoveries for PGE, Cu, and Ni are correlated with improvements in the flotation kinetics of their slow-floating components. IntroductionShort-chain (less than C6) xanthates are very effective for the bulk flotation of sulphides (Fuerstenau, 1982), and early work (Leja, 1968; Gaudin, 1957; Plaksin and Bessonov, 1957; Taggart, Giudice, and Ziehl, 1934) indicated that the presence of oxygen in flotation slurries is necessary for the oxidation of the xanthate collector at the sulphide mineral surface to induce hydrophobicity. Fundamental research into the chemistry and adsorption mechanisms of xanthates over the years (Finkelstein and Poling, 1977; Woods, 1976; Winter and Woods, 1973) has revealed that for iron-bearing sulphide minerals, adsorption occurs predominantly through a charge transfer process. Oxidation of the adsorbed collector to the corresponding dimer takes place if the mixed potential of the system is greater than the reversible potential for dimer formation. In oxygenated slurries the rate of adsorption and oxidation of the collector depends greatly on the substrate surfaces. For chalcopyrite (Guler et al., 2005; Leppinen, 1990; Roos, Celis, and Sudrassono, 1990) and pentlandite (Hodgson and Agar, 1989) a two-step interaction with xanthate is proposed in which the chemisorbed xanthate is further oxidized to the dimer. The initial interaction of xanthate with pyrrhotite is through physisorption where xanthate physisorbs onto positive surface sites followed by oxidation to dixanthogen (Khan and Kellebek, 2004; Bozkurt, Xu, and Finch., 1998). This process is, however, slow and increased reaction time is needed to improve flotation recovery (Buswell and Nicol, 2002)."

Oct 1, 2018

1. Book reviews Tungsten: 1982. London, Mining Journal Books Ltd, 1982. 179 pp. Reviewer: G.A. Brown The geology of industrial minerals in Canada, edited by G.R. Guillet and Wendy Martin. Canadian Institute of Mining and Metallurgy, special volume 29. Reviewer: R.W.O. Kersten Foam flotation - theory and applications, by Ann N. Clarke and David J. Wilson. New York, Marcel Dekker, 1984. 418 pp. Reviewer: B.K. Loveday Industrial and financial indicators of the steel industry, by Patrick Genevaz. Paris, La Chambre des Cartes, 1982. 2 vols. Vol I: Analysis and conclusions, FF3500. Vol. 11: Tables, FF4000. Reviewer: R.J. Dippenaar An encyclopaedia of metallurgy and materials, by C.R. Tottle. Plymouth, Macdonald and Evans and The Metals Society, 1984. 481 pp. RI44,50. Reviewer: P. T. Wedepohl The role of crack growth in metal fatigue, by LP. Pook. London, The Metals Society. Reviewer: C.A. Boothroyd Hydraulic coalmining - new technology and its geological and industrial significance, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 33 pp. Hydraulic coalmining - hydromining update: potential impact on coal deposits and coal mining industry, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 130 pp. Victoria&apos;s brown coal. A huge fortune in chancery, edited by J .T. Woodcock. The Australasian Institute of Mining and Metallurgy, 1984. 204 pp. Reviewer: J.J. Versluis 2. Canadian publications The following reviews of the activity and developments during 1982 in respect to the chief minerals produced or consumed in Canada are now available. Zirconium. An important mineral commodity. Mineral Policy Sector, Mineral Bulletin MR 202, $6.60. Canadian minerals yearbook 1982. Mineral Policy Sector, Mineral Report 32, $40.75. Canadian reserves of copper, nickel lead, zinc, molybdenum, silver and gold as of January 1, 1983, by W.H. Laughin. $4.20. Mineral Policy Sector, Mineral Bulletin MR 201. Sulphur market profile, by B.W. Boyd. Mineral Policy Sector, MRI 84/5. 3. Mintek publications Report M123 The use of of activated charcoal in a NIMCIX column for the recovery of gold from cyanide solutions. Report M150 Energy transfer in the hearths of submerged-arc furnaces. Report M151 A preliminary investigation of the initiation of pitting corrosion in austenitic stainless steels and nickel-based alloys. Report M154 The reduction of Winterveld chrome spinel at 1300°C under an argon atmosphere in the presence of carbon. Report M165 The development of an improved on-line gold analyser. Report MI67 three nebulizers for use with an inductively coupled plasma spectrometer. 4. New publications Mineral Industry Consultants Association (as at 31st March, 1984). Parkville (Australia), The Australasian Institute of Mining and Metallurgy, 1984. 112 pp. Philosophical and procedural guidelines for the planning professions. Johannesburg, the Environmental Planning Professions Interdisciplinary Committee (EPPIC, P.O. Box 61019, Marshalltown 2107), R2.50. Directiona//y solidified materials for high temperature service, by M. McLean. London, the Metals Society, 1983. 337 pp. Tin and its uses no. 142. Greenford (England), International Tin Research Institute, 1984. Metals engineering International Symposia & Exhibitions Ltd - a subsidiary of Industrial Newspapers PLC - are pleased to announce that they will be organizing a mammoth engineering event, entitled Metals Engineering 86, comprising five important exhibitions in 1986:. Agglomeration A major symposium on agglomeration is being organized in Toronto for the 2nd to 5th of June, 1985. Speakers from around the world (Canada, U.S.A., Brazil, Australia, Japan, West Germany, Italy, India, China, Switzerland, Poland, Yugoslavia, and France) will address delegates on various aspects of agglomeration relative to iron ore, coal, coke, and fuels. Plenary theme papers will also be presented by speakers from Japan, the U.K., and the Netherlands.

Jan 1, 1985

By R. Tinsley

Project-finance risk assessment is mature and approached systematically. Mining industry due diligence remains fragmented with specialists addressing different aspects of the project such as reserves/JORC, environmental impact, commodity market, even financial analysis/ modelling. Each professional has a natural tendency to believe that the risk factors they have examined are the key ones necessary to be reviewed, as if their review will stand in isolation from others in the way a project materialises. By first laying out the project risk categories and risk matrices, this paper examines the due diligence process with a keen eye to the risk assessment and overlap/interaction. Some cross fertilisation of due diligence techniques from other industry sectors is placed into the mining context. Six case studies are then presented with regards to due diligence features in each project&apos;s feasibility review or financial information/ offering memorandum. A power case first shows the differences between the due diligence expectations of banks versus bond financings. Then some Australian and Indonesian mining development cases are analysed to see the due diligence learning points. Some of these were project/due diligence failures. The conclusion focuses on the value of a systematic risk assessment for project evaluation, all from the project-finance perspective.

Jan 1, 2007

By N. Coulson, P. Ledwaba

"The University of the Witwatersrand presents an accredited four-course training programme for community relations practitioners (CRPs). Between May 2013 and October 2014 six courses were facilitated for 145 participants, of whom 82% were from sub-Saharan Africa, 62% worked in mining, and 58% worked directly with communities. Thematic analysis of the comments of course participants collected during course exercises found that there were a set of coherent drivers for resilient companycommunity relationships, but that the restrainers to resilient relationships were often context-specific and dominated by politics. CRPs reported facing as many difficulties in the internal company environment as in the external environment. These findings for CRPs in Africa resonate with those worldwide.InroductionMuch has changed in how the extractive industry responds to social and community issues. There has been a growing prioritization of community-related issues within the extractive industry globally (Kemp, 2010; Tatar, n.d.). According to Kemp (2010) this can be attributed partly to escalating pressure from local-level stakeholders to push mining companies to take greater responsibility for the social, economic, and environmental impacts of mining. Securing and maintaining the social licence to operate is ranked fourth in terms of the top risks facing the mining and metals industry in 2016, up one place from 2015 (Ernst & Young, 2016).Conflicts between local communities and large-scale mining companies arise because of the social, environmental, and economic impacts of mining. Worldwide, large-scale mining companies have a poor reputation amongst communities, including those in Africa (Gilberthorpe and Banks, 2012; Kemp and Owen, 2013a; van Wyk, n.d.). For mining companies, conflicts for whatever reason, result in loss of productivity, lost opportunities, lost time, and adverse impacts on reputation (International Council on Mining and Metals, 2015). Conflicts also have a significant financial impact on mining operations (Franks et al., 2014). Davis and Franks (2014), estimated that US$10 000–50 000 is lost each day when a project is delayed during the exploration phase, and about US$20 million per week when in operation. Today these costs could be expected to be higher due to increasing input costs."

Jan 1, 2017

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987