Search Documents

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southernsector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite-anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only theUG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000tons at full run of mine production from the underground UG2 mine.

Jan 1, 2006

By T. Bednarski, L. Thomas, G. Banza, D. Muteba, P. Cole, M. Soderstrom

"In copper solvent extraction, aqueous-in-organic entrainment results in the carry-over of unwanted species into the electrowinning process with negative cost implications. The need to bleed is increased and the purity of the copper cathode is potentially compromised, depending on the impurities being transferred (Cl, NO3, Fe, Mn). In some cases, entrainment results in elevated levels of manganese in the electrolyte which can cause oxidative conditions to develop and degradation of the organic phase. Degraded organic phase detrimentally affects the physical performance of the copper solvent extraction process, contributing to even higher aqueous-in-organic entrainment. Aqueous entrainment may be minimized through good operating practices and maintenance of the organic quality, but the accurate measurement of entrainment remains a challenge. This paper presents coalescing devices designed to provide more exact measurements of aqueous-in-organic entrainment. IntroductionMany copper solvent extraction (SX) plants experience high aqueous-in-organic (A-in-O) entrainments but are unaware of the extent of the problem because entrainment is often not measured. Aqueous entrainment results in the carry-over of unwanted species into the electrowinning (EW) process and the need to bleed to maintain acceptable concentrations in the electrolyte. The costs associated with the bleed are exacerbated in copper plants where aqueous entrainment levels are high. Other than these direct costs, there are operational consequences of the build-up of certain species in the EW circuit that can have deleterious effects on plant performance.Minimizing aqueous entrainment in operating plants requires an understanding of the factors that affect entrainment levels. Both chemical and operational influences are discussed in this paper. The difficulty of obtaining a representative sample makes it challenging to obtain an accurate measure of aqueous entrainment from a continuous process like SX. Coalescing devices used to get a more precise measurement of A-in-O entrainment are useful to complete mass balances around the SX circuits. Alternatively, mass balances can be used to estimate aqueous entrainments and are helpful as a tool to troubleshoot operations with a view to improving plant performance."

Jan 1, 2016

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By G. D. Schena

The issue of evaluating the economic impact of large mineral projects in developing countries was studied by the use of econometric models. The evaluating system is demonstrated by its application to an example from Namibia. Three-dimensional graphics are used to illustrate the procedures leading to an assessment of the economic effects of the mineral development. The analysis allows the assessment of the overall economic consequences of mineral developments where there is a need to incorporate in the evaluation issues that are broader in scope than the pure financial objectives. Sets of technical coefficients are exploited for the development of input-output models of the productive structure of an economy. The models are refined to incorporate country-specific behaviours. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy wide effects associated with a new project in the mineral sector of a developing country. Synthetic measures of profitability at market and shadow prices are introduced, and the cost/benefit ratio is used to rank mineral projects according to their economic profitability. The cost is the capital mobilized for the development of the project and for increasing the productive capacity of the related satellite industries. The benefits are identified with the economy-wide increase in value added induced by the project. 80th costs and benefits are initially valued at market prices. Their ratio is likely to be an index of economic profitability superior to measures that concentrate exclusively on the benefit side of projects. To allow for market distortions, the concept of shadow prices is introduced, and accordingly project-related costs and benefits are re-evaluated. A new cost/benefit ratio at shadow prices is recalculated, which is more meaningful to the policy-maker than decision-making based on socio-economic issues.

Jan 1, 1993

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractor's and owner's perspectives and focuses on: ? when performance tests are required, ? what type of performance test/warranty is optimum for each type of project, and ? how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between owner's risk and contractor's risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the owner's corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide `common purpose' early in the contract negotiation process.

Jan 1, 2007

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009

By G. Dhakal, J. -I. Kodama, K. Neaupane, T. Yoneda

ABSTRACT Durability tests and evaluation of sub-zero temperature effects to some argillaceous clastic rocks were carried out. Welded tuff, limestone, sandstone and schist samples collected from different parts of Japan were tested and results are presented. Schist and dolomite from Ganesh Himal area along the higher Himalayas of Nepal were also tested, and the results are compared. The slaking tests were performed on all samples in pure water. The results reveal that the slaking index of schist from Japan is lower than that of schist from Nepal. Regarding carbonate rocks, the slaking index of limestone from Japan is higher than that of dolomite from Nepal. A tendency of decrease in slake durability with an increase in porosity is also observed. Freezing and thawing experiments conducted on welded tuff and schist reveal that crack initiates earlier but extends slower in schist than in welded tuff. It is also observed from the freeze-thaw experiment that the welded tuff deteriorates and wears faster than the schist. However, sandstone remains relatively intact for a long run of freeze-thaw cycles. Zusammenfassung Beständigkeitstests sowie die Bewertung der Auswirkungen von Minusgraden auf Tonschiefer Trümmergestein wurden durchgeführt. Dabei wurden geschweißter Tuff, Kalkstein, Sandstein und Schiefer aus verschiedenen Gebieten Japans sowie Schiefer und Dolomitgestein aus dem Ganesh Himal Gebiet, dem höheren Himalaya Nepals, untersucht und die Resultate verglichen. Für alle diese Gesteine wurden Slaking-Tests in reinem Wasser vorgenommen. Die Resultate zeigen, dass das Slaking von Schiefer aus Japan höher als das von Schiefer aus Nepal war, wohingegen bei kalkhaltigem Gestein das Slaking von Kalkstein aus Japan niedriger als das von Dolomitgestein aus Nepal ausfiel. Es wurde dabei auch eine Tendenz zur Löschbeständigkeitsverringerung bei gleichzeitig erhöhter Porosität beobachtet. Gefrier- und Tautests an geschweißtem Tuff und japanischem Schiefer zeigten, dass Risse in Schiefer schneller auftraten, aber sich langsamer ausweiteten als in geschweißtem Tuff. Bei Gefrier- und Tautests wurde ebenfalls beobachtet, dass geschweißter Tuff schneller verfällt und verschleißt als Schiefer. Sandstein hingegen blieb über lange Tau- und Gefrierzyklen intakt Résumé Des tests de solidités et l’évaluation de l’effet des températures en dessous de zéro sur les rocs argileux ont été effectués. Les rocs d’origine volcanique (cendre), les rocs calcaires, sableux et les schistes de différentes régions du Japon, ont été étudiés. Les schistes et les dolomites de la région de Ganesh Himal le long du haut Himalaya (Népal) ont été étudiés et comparés à ceux du Japon. Les tests de désintégration sur les rocs ont été effectués dans l’eau pure. Les résultats montrent que l’index de désintégration des schistes du Japon est inférieur aux schistes du Népal. En ce qui concerne les rocs carbonyles, l’index de désintégration des rocs calcaires du Japon est supérieur à ceux des dolomites du Népal. Une décroissance de la résistance à la durabilité est observée avec une plus grande porosité des rocs. Les tests de congélation-décongelation sur les schistes et les rocs d’origine volcanique (cendre) du Japon montrent une apparition précoce des fissures mais l’expansion des fissures est plus rapide dans les rocs volcaniques. Des tests similaires montrent que les rocs volcaniques (cendre) se désagrégent plus rapidement que les schistes. Cependant, les rocs sableux restent intacts après plusieurs cycles de congélation-décongélation.

Jan 1, 2003

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

By W. A. Hodgson

"In order to be able to map the variation in the concentration of elements in soils, it is necessary to sample at intervals that will give adequate coverage of the area and will allow determination of the rate of fluctuation of concentration with distance in any environment. This rate of fluctuation with distance can be referred to as the continuity of concentration.The continuity of concentration in soils varies according to the chemical characteristics of the element being considered, the underlying rock type or orebody and in response to the dispersion processes that operated during soil formation. Within any environment there is a maximum distance between sampling points within which adjacent sample values are related. This distance, the critical sampling interval, can be determined by means of a correlograrm.Where the sampling grid has been chosen to provide an adequate coverage over unmineralized rock, adjacent samples being related, anomalies may be missed if the element continuity in the anomaly is less than in the background. Results show that a knowledge of the critical sampling interval of the environment being examined may used to select a more efficient sampling pattern for a geochemical survey."

Jan 1, 2014

By R. R. Mankowski, F. J. Cox

Experimental results are presented on the longitudinal atenuation of a kinetic shock wave traveling along a typical mine hoisting cable. Mathematical curve-fiting of the results established these losses to be exponential and tension-dependent. The reflection and power-transmission coeficients of a typical winding drum were also investigated. The degree of penetration of an incident stress wave onto the coil of cable wrapped round the drum is shown to be governed by a second-degree relationship, and is solely dependent on the acceleration of the cable at the cable-drum interface. Although the investigation is limited to the testing of a single hoisting cable, certain qualitative trends that were identified can be generalized and applied to other types of hoisting cable with diferent geometries, elastic properties, and instalations.

Jan 1, 1986

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused by media when the particle or lump is too big in relation to the media to be readily nipped; and self-breakage resulting from the chip¬ping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions. A simplified form of the model was used to predict the performance of an 8 m diameter SAG mill with L/D = 0.5 grinding a copper ore, and predicted maximum capacity and minimum kWh/ton at about 6% ball load at 25% total filling. Two FAG mills of L/D = 2 were necessary to give the same capacity, and the simulations indicated a lower kWh/ton for these mills. For this ore, both systems were technically feasible.

Jan 1, 1987

By S. Potgieter-Vermaak

The main mineral components of the so-called heavy sands (or black sand) are the titanium, zirconium and iron-bearing minerals, rutile, zircon and illmenite, accompanied by various minor and trace amounts of silicates or phosphates, often present together with the rare earth elements. The investigated samples originated from Richards Bay Minerals (RBM) in South Africa, which is jointly owned by BHP Billiton and Rio Tinto, the largest titanium slag producer in the world. The present study focused on the characteristics of samples originating from various points in the separation plant. The heavy-mineral fractions and concentrates of a representative suite of samples were investigated using various analytical techniques to establish the differences in morphological and elemental compositions at the different points in the plant. These techniques included: reflected light microscopy, micro-raman spectrometry (MRS), scanning electron microscopy coupled with energy dispersive X-ray analysis (SEM/EDX) and structural and chemical analyser (SCA). All samples comprised a heterogeneous population of zircon and rutile grains with diverse physico-chemical properties, expressed by large differences in colour and trace element chemistry of single grains. The elemental composition proved the presence of the rare earth elements that appeared to coexist with both Ti and Zr minerals. The percentage of grains hosting inclusions, such as anatase, monazite, quartz, spessartine, augite, epidote and actinolite, varied for each sample and could be uniquely characterized by Raman investigations. Keywords: heavy mineral sands, micro-ram an spectrometry, elemental analysis

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007