Search Documents

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board's management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By G. T. van Rooyen

The susceptibility of a low-alloy steel that has been hardened and tempered-826 M40 (EN26)-to embrittlement by strain aging during service was simulated by artificial aging of specimens at 100°C. It was found that the brittle transition temperature of both monotonic and cyclically strained material was increased by only about 25°C as a result of strain aging. It is concluded that the susceptibility of low-alloy steels in the hardened, tempered condition is less than that of low-carbon steel, and that such steels qualify for exemption of the periodic 'annealing' required by the Mines and Works Act.

Jan 1, 1986

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

ADVANCES IN EXTRACTION METALLURGY AND REFINING A symposium organised by the Institution of Mining and Metallurgy will be held in London from 4th to 6th October, 1971. Particulars can be obtained from: The Secretary, Institution of Mining and Metallurgy, 44 Portland Place, London WIN 4BR, ENGLAND. ICAMC -71 - HUNGARY The Third International Conference on Automatic Control of Mines and Collieries will be held at Balantsfured, Hungary from 27th to 30th September, 1971. Further particulars can be obtained from: ICAMC - 71, Budapest 3, P.O. Box 115, HUNGARY. AUSTRALIAN INSTITUTE OF MINING AND METALLURGY Illawarra Branch A symposium on "Blast Furnace Injection" is to be held at Wollongong University College from 15th to 17th February, 1972. About 20 papers on various aspects of blast furnace injection will be presented, including two on nonferrous furnaces. Further particulars may be obtained from: N. Standish, Chairman, Symposium Committee, Wollongong University, Australia 2600.

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020

By A. Atta-Quayson

Since 2012, Ghana has been implementing local procurement regulations in the mining sector to broaden and deepen linkages between mining and other sectors of the economy. The regulations have been implemented in collaboration with the mining industry. This paper offers an in-depth analysis of how the local procurement regulations and related initiatives have been implemented so far. Primary data gathered with semi-structured interviews and secondary sources of data indicate a steady improvement in both in-country procurement and local manufacturing of inputs for the mining industry. There are, however, some challenges relating to tariff structure and support (financial and technical) for local suppliers and manufacturers to meet high standards and demands of the mining industry. This calls for a well-thought-out strategy and programme of activities to sustain and improve on progress made.

Feb 2, 2022

By M. R. Khalesi, Y. Kianinia, A. Seyedhakimi, F. Soltani

"The feed ore to Agh-Darreh gold processing plant (Takab City, Iran) contains 2 ppm Au, 7 ppm Ag, and 120 ppm Hg. After cyanide leaching of the feed at pH 10.4, 80% of the total mercury (in the form of cinnabar and metacinnabar) goes to the tailings dam. In this research, separation of mercury from the tailings by flotation was investigated. The effects of collector type and dosage, pH, and the number of cleaner stages were studied. The results showed that after two stages of cleaning a 40–62% recovery of Hg at a grade of 14.3% Hg is attainable. Recycle water from a test in which 50 g/t amyl xanthate and 30 g/t pine oil was used in the flotation stage showed no adverse effect on the leaching and adsorption of gold onto activated carbon.IntroductionMercury, most commonly found in the nature as the mineral cinnabar (HgS), is a hazardous substance because of its mobility and toxicity (Kyle et al., 2012). Roasting is the wellestablished treatment method for mercury ores, in which the sulphur is burned and volatilized and mercury recovered subsequently by cooling and condensation. However, for low-grade ores, flotation is mainly applied for primary concentration due to its comparatively low costs, low environmental hazards, and flexibility regarding feed variations (Bulatovic, 2007). Particularly, cinnabar can be easily recovered by flotation using pine oil and a collector such as xanthate (Bulatovic, 2007; Crozier, 1991). Floatability of cinnabar is reduced due to surface oxidation when it is exposed to the atmosphere after crushing. This problem can be eliminated by adding copper sulphate and lead nitrate or acetate. The best pH for cinnabar flotation is in the range of 6.5 to 8.5 according to Erspamer and Wells, (1954), who reported that cinnabar and stibnite can be floated with long-chain xanthate collectors and an alcohol frother, with cumulative recoveries of 97.8% and 94.7%, respectively. Lead acetate was used as an activator."

Jan 1, 2017

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By I. D. Wood

The geostatistical methods given for the estimation of low-ash coal reserves take into account the geological structure of the seam, and consequently give far more reliable results than have been obtained in the past. Confidence limits are given for all the estimates.

Jan 1, 1979

By K. Muchima, C. Siame, L. Little, B. Kaputula, Q. Mclennan

"The variability of copper mineralization at Kansanshi mine significantly affects the efficiencies of the processes used to recover copper. Quantifying this variability is therefore essential for monitoring and optimizing the performance of the concentrator, which comprises three different flotation circuits (sulphide, mixed, and oxide) and an atmospheric leach circuit. Onsite automated scanning electron microscopy with energy-dispersive X-ray spectrometry (Auto-SEM-EDS) is used to analyse routine weekly composite samples for each circuit, providing detailed analyses of bulk mineralogy, copper deportment to different minerals, mineral liberation, and associations. Weekly mineralogical trends are used to assess changes in process performance, and characterization of the copper losses has inspired a number of projects to target the specific particle types responsible for the main losses. In this paper we describe the relationship between mineralogy and plant performance at Kansanshi, and discus IntroductionKansanshi is a copper and gold mine located in the Northwestern Province of Zambia, with an annual production in the region of 250 000 t of copper and 160 000 ounces of gold. Ore mined from the epigenetic vein-hosted deposit is classified into three ore types based on the extent of oxidation and supergene enrichment. Sulphide, oxide, and mixed ore are fed to separate mineral processing circuits tailored for recovery of the dominant copper minerals in each. After comminution to a target grind size of 80% passing 150 µm, each ore type is subjected to flotation to recover the copper sulphide minerals (chalcopyrite, bornite, chalcocite, covellite). The oxide float tails and a large proportion of the mixed float tails are then treated by atmospheric leaching to extract copper from the remaining copper-hosting minerals, which include cuprite, malachite, chrysocolla, and delafossite. Some native copper is recovered by flotation and some of it is recovered by leaching. A small portion of the combined concentrate from all circuits is subjected to high-pressure leaching and the rest is sent to the smelter. Sulphuric acid produced during smelting is used for the atmospheric leach."

Nov 1, 2018

By A. J. Rogers

The KX36 kimberlite was discovered using a high-resolution gradient aeromagnetic survey, with follow-up detailed ground geophysics and deflation soil sampling used to assess and prioritize the geophysical anomalies identified from the initial aeromagnetic survey. Prospect drilling intersected kimberlite in the first hole drilled on the KX36 anomaly. Preliminary evaluation has shown that KX36 is diamondiferous, and a more detailed evaluation and sampling programme is currently underway. The area around KX36 has been prospected by numerous companies over the last few decades, with sporadic kimberlite indicator mineral (KIM) recoveries in regional deflation sampling indicating the possible presence of kimberlites, but without sufficient resolution to ?home in? on specific targets. Previous (lower resolution) aeromagnetic surveys and soil sampling campaigns also did not define anomalies with sufficient detail to guide prospect drilling effectively. The discovery of KX36 highlights the prospectivity of areas of Botswana under deep Kalahari cover that have been explored previously. Keywords kimberlite exploration, central Kalahari, overburden, high resolution aeromagnetics, deflation sampling, KIM.

Jul 1, 2013

By N. A. Chapman

The effect of using conventional crushing and HPGR in combination with dry or wet milling was investigated using a base metal sulphide (sphalerite), and a PGM (platinum group minerals) ore in order to determine how these different processes affect the flotation performance. In the case of sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc. Conversely, in the case of PGMs, a similar treatment produced the poorest results. The results were investigated further by comparing the relative effects of factors such as percentage liberation, particle size, and surface properties of the samples produced by the different milling procedures as well as the concentrates and tailings obtained from the flotation tests.

Jan 1, 2013

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By K. Koruyan

Although remote sensing technology has been available for many years, it has rarely been used for monitoring mining activity. Recent studies indicate that remote sensing is also a valuable tool for managing and planning certain aspects of the mining operation. In this paper, we examine areal expansion of marble quarries and the affected vegetation over a period of 10 years in the Mugla region in Turkey, using geographic information system (GIS) and remote sensing (RS) techniques. Images captured by ASTER Level 3A01 (3D Ortho Data Set), Landsat 5, and Landsat 7 satellites between 2001 and 2009 were used for the analysis. Changes in the natural vegetation as a function of the production level in the marble quarry were calculated using the normalized difference vegetation index. According to the study results, land cover and natural vegetation decreased by less than 3 per cent and 1 per cent respectively between 2001 and 2009, following an upsurge in mining activity in the region.

Jan 1, 2012

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013