Search Documents

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

"A coordinated, integrated research effort aimed at studying the scientific, engineering and medical aspects of the respirable dust problem is underway in the areas of dust generation, dust dispersion and dilution, dust characterization, interaction of dust and lungs, and relationship of seam characteristics to dust generation and mobility. (FIGURE 24) The Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the dust-lung interaction processes that lead to mine worker disability. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated.Research projects in the Generic Mineral Technology Center for Respirable Dust have effected several improved methods for the preparation and characterization of the dusts needed by these projects. Superior procedures for generating ""standard"" dust samples have been developed and are in regular use in the laboratory. Questions raised during the course of some projects regarding ""stale"" versus ""fresh"" dust have led to the development of sampling techniques where the dust is directly collected in a surfactant. MSHA and CANMET have requested and received information on Center generated software. An equipment manufacturer, TSI, Inc., requesting input on modifying the inlet of an aerosol sampler has been assisted as a result of research that was conducted at the University of Minnesota.The objectives, scope and progress of all the research projects in the Center, in the form of abstracts and reports, have been detailed in Volume 1 of this series. Research papers written by the principle investigators and resulting from the findings of projects (FIGURE 25) and which are funded by U.S. Bureau of Mines grant number G1135142 have been published in Volumes 3 through 6 and Volume 8 of this series. Volume 2 relates the cooperation and interaction of the U.S. Bureau of Mines and the Generic Mineral Technology Center for Respirable Dust in research on the problem of respirable dust in the mineral industries."

Aug 31, 1989

By Deno M. Pappas, Christopher Mark, Eric R. Bauer

During 1998-99, groundfall incidents resulted in 27 fatalities and were responsible for over 70% of all deaths in U.S. underground coal mines. To obtain a better understanding of where and why these incidents occurred, a comprehensive analysis of ground fall injuries and fatalities was conducted. The first portion of the study examined various factors associated with roof and rib fall injuries and reportable roof fall noninjuries that occurred during 1995-98. The study found that the room-and-pillar mining method has twice the groundfall incident rate than the longwall method. Mine locations with high groundfall rates seem to correlate to regions where there is a higher concentration of problematic coalbeds. For example, the Illinois Basin has very high groundfall rates, which can be traced back to several key coalbeds-Kentucky No. 13, Herrin/No. 6/Kentucky No. 11, and Springfield No. 5/Kentucky No. 9. High rib fall rates were found in mines located in thick seams. Groundfall rates were found to be 30% to 40% higher during the months of July through September, possibly due to high humidity that may cause the shale mine roof to deteriorate. The second part of the study examined the root causes of failure by reviewing all groundfall fatality reports for 1996-99. Primary and secondary hazard factors were assigned to each groundfall incident. The primaryf actors resulting in these groundfall fatalities were pillar extraction, traveling under unsupported roof, skin failure, construction, longwall faces, intersections, and geologic discontinuities. Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 10, 2000

Lower the respirable dust exposure of longwall shearer operators by isolating and con-fining the dust cloud near the face. Approach Install conveyor belt screens at various locations on the body of the shearer to contain and hold the dust cloud toward the face side of the machine. This approach provides a cleaner air split in the walkway, over the shearer operators. How It Works On most longwall shearer sections, the dust exposure of the shearer operators is primarily attributable to the machine it-self. The dust cloud originates at the face, and the exposure of the operators depends largely on how quickly this dust spreads into the walkway. Conveyor belt screens placed on the gob side of the body of the machine can reduce the amount of dust which spreads out into the walk-way. In addition, belting may be installed over any open spaces between the shearer under-frame and the panline to prevent conveyor dust from boiling out into the operator's walkway.

Jan 1, 1981

By Charles L. Kimbell

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom has been continued this year in tables 23 and 24. As a result of the lack of availability of comprehensive data on the prices of metals in Canada, the table that had presented that information in past years in this chapter has been discontinued and the price series for nickel that had been in that table now appears in the table presenting metal prices in the United States.

Jan 1, 1993

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By O. P. Hood

The smoke problem means different things in different places . In the neighborhood of industrial plants , especially smelting plants and cement plants , the term " smoke " is applied to material discharged from these plants , consisting of a mixture of solid particles ( dust ) , fume which has condensed from vapors , and gases of various kinds that are produced in the operations . In the ordinary use of the word , however , " smoke" refers to the visible material which escapes from the burning of coal . White smoke usually owes its color to small drops of water which have condensed from the water vapor that it formed in the burning of coal . When smoke is black, the color is due to unconsumed particles of carbon and usually when the smoke problem is spoken of , it is this black smoke produced in the burning of coal that is referred to , Many inquiries in regard to smoke are addressed to the Bureau of Mines , and the following brief summary has been prepared as covering the usual questions . For references to the smoke problem in England , I am indebted to a recent interesting paper on this topic by David Brownlie .

Feb 1, 1922

By Alex C. Smith, Thomas P. Mucho, John B. Walsh, Alden Ozment, Michael R. Thibou, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), with US Foam Technologies, Inc. and On Site Gas Systems, Inc., conducted research on the remote application of extinguishing agents with the intent of improving deployment strategies to limit miner exposure and to help ensure the best possible outcome during a mine fire. Full-scale in-mine were conducted at the NIOSH Lake Lynn Experimental Mine to determine the flow characteristics, stability and fire-suppression capability of gas-enhanced foam. The in-mine experimental work was designed to evaluate movement of gas-enhanced foam through mine workings closely simulating an underground coal mine environment and how long gas-enhanced foam would remain stable. This paper presents results of the experiments and provides valuable insight into mine fire deployment strategies for gas-enhanced foam technology.

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By David J. Ellis

The mineral industry of Benin continued to be confined to the production of cement, crude oil, salt, and sand and gravel. Only crude oil and cement were exported, with the value of crude oil exports and cement exports constituting about 20% and 2% of export revenue, respectively. The value of crude oil exports was less than the cost of imports of refined petroleum products. Production of crude oil was unchanged from 1986, averaging 5,500 barrels per day (bbl/d). The Government managed the facilities at the Semé Oilfield while actively seeking a new manager to replace Pan Ocean Oil Co. of Switzerland, whose contract was canceled in 1986. Recoverable reserves of crude oil were estimated to be between 18 and 30 million barrels.

Jan 1, 1989

By Robert F. Chaiken

A quasi-steady-burning channel model is used in this Bureau of Mines study to describe the conductive heat loss from an in situ coal combustor to the surrounding rock strata. The calculated heat losses are significantly greater than those previously estimated, but are still very acceptable from the viewpoint of energy recovery. Approximately 80% to 90% of the heat of combustion of the coal should appear as sensible heat of the gaseous exhaust, with exhaust temperatures in the range of 1,000° to 1,200° C. The effects of burning stoichiometry and channel size on the heat loss are also discussed in terms of the model. Such effects are shown to be compatible with an in situ combustion process even in thin seams. However, these results depend on gas leakage and adverse roof falls not being important factors in deter-mining the heat loss mechanism.

Jan 1, 1977

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By A. E. Prokop, J. P. Rider

Previous research on continuous mining operations has shown that significant interactions exist between dust control parameter application and the resulting respirable dust levels, but simply increasing the level of the controls does not guarantee a reduction in respirable dust levels. Full-scale laboratory tests are being conducted to provide information to longwall operators which would assist them in selecting control parameters that would reduce dust levels for mine-specific conditions. The interactions between face air velocity, shearer water quantity, drum water spray pressure, external water spray pressure, and spray system design were evaluated in a simulated 2.13. m (7-ft) coal seam for two cutting directions. Locations around and downwind of the shearer were monitored to evaluate relative changes in respirable dust levels as a function of each control parameter.

Louisiana's coal reserves, located in the north-western part of the state, consist entirely of lignite, with estimated recoverable reserves of about a billion tons. Although lignite deposits were discovered in the early 1800s, the first documented use of lignite occurred at the federal arsenal near Shreveport during the Civil War. By the late 1800s, lignite use was common by blacksmiths, railroads, and steamboats. Lignite production ceased, however, from the early 1900s until 1985. A new lignite mine permitted September 1, 1985, produced 0.2 million tons in its first year. The operation uses a seven-mile-long conveyor to transport lignite to the associated mine-mouth power plant. The surface coal mining reclamation and enforcement program in Louisiana was approved October 10,1980. Louisiana's Abandoned Mine Reclamation Plan was approved December 10, 1986

Jan 1, 1992

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By E. P. Youngman

Although, an effort has been made to standardize and codify the mining law to apply to the entire German Nation, nothing has yet been accomplished. abstract, which applies only to Prussia, the largest and most important of the German States, is based upon the Prussian Mining Law (Preussisches Berggesetz) of June 24, 1865, which grants to certain provinces, communities, and districts special exceptions, of no particular significance, except locally.

May 1, 1930

By H. M. Lawrence

The recovery of phosphate rack from the ores in the land-pebble district of Florida is a simple washing and screening operation. In the gashing plants coarse phosphate only is saved. Log-Washer overflows and screen-undersize products containing an appreciable content of fine phosphate are discarded. The phosphate grains in the material discharged to waste are generally finer in size than the mesh--14 to 20 mesh or 0.346 to 0.03 inch--of the finest screen in the washer. The operators state that the washers ordinarily recover from 50 to 60 per cent of the phosphate content of the matrix mined. Any increase that can be effected in the recovery of phosphate would be of advantage to the industry and would conserve the mineral resources of the country. In considering possible methods that might increase the recovery obtained in phosphate-washing plants the application of flotation, if it could be successfully developed, seemed to warrant investigation.

Jan 1, 1928