Search Documents

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By A. W. Hall

Cylindrical plastic scintillators were investigated for efficiency in detecting neutron-induced prompt gamma rays. Scintillator performance was compared on the basis of half-resolution and peak-to-trough ratios for gamma spectra obtained from Co-60 (1.17 and 1.33 MeV), Th-228 (2.62 MeV), and PuBe (4.43 MeV). Various sizes of Pilot Chemical scintillators (types B, F, M, and Y) were tested. The best half-resolution, 7.7 percent for PuBe, was achieved with a 5-by 5-inch Pilot Y?scintillator and dual photomultipliers. Comparison with sodium iodide (NaI) scintillators and the use of plastic scintillators for on-stream analysis of sulfur in coal is discussed. Plastics were found to be unsuitable for on-stream analysis of materials having complex prompt gamma ray spectra; however, they could conceivably be used for those yielding Simpler spectra.

Jan 1, 1974

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By J. B. Janus

This Bureau of Mines publication updates a series of reports on the quality of coal purchased under specifications for Government use. Listed are analytical data on the composition and quality of tipple and delivered samples of coal collected during the period July 1975 through September 1976.

Jan 1, 1977

Although early Spanish settlers used coal several centuries ago, significant commercial coal mining in New Mexico began in 1861, when the U.S. Army opened a mine to supply Fort Craig. Since then, coal from the state has been used to fuel railroads, lead and copper smelters, and other local industry. In recent years, lower-cost strip mining methods and an increased demand for coal by electric utilities in the Southwest have caused an increase in New Mexico coal production. The coal-bearing regions of New Mexico underlie about 25,000 square miles or20.6 percent of the total area of the state. However, the majority of coal-bearing regions lie under Indian lands that are regulated by the Office of Surface Mining (see Navajo and Hopi data on pages 72-75). Today, most of the coal produced in New Mexico comes from the San Juan Basin in the northwest part of the state and the Raton Area in the north central part. New Mexico's reserves are estimated to be 4.6 billion tons, about one percent of the national reserve. New Mexico's permanent regulatory program was conditionally approved December 3 1, 1980. Its Abandoned Mine Lands Program was approved July 17,198 1.

Jan 1, 1992

Develop a method of dewatering ultrafine mineral waste that will increase water recovery from the waste and produce a dewatered material that eliminates the need for large settling ponds. Background In the hydrometallurgical treatment of many ores and concentrates to recover mineral values, slurries of fine particles are generated. Some of these slurries settle slowly and are difficult to dewater. This inherent property causes environmental and handling problems for the minerals industry. Examples of such problem wastes are clay wastes generated during the mining and beneficiation of phosphate ores, the processing of coal to produce a low-ash material, the cleaning of bentonite, beneficiation of potash, and the recovery of mica from clay-containing ores. At the present time these waste slurries are treated by techniques such as impoundment, thickening, and thickening followed by filtration. But factors such as new environmental regulations, the loss of mineral values in the waste slurries, the need to recycle water in the processing facility, and the lack of land suitable for impounding the waste have shown that new technology will be needed in the future to handle waste slurries.

Jan 1, 1986

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

By R. Larry Grayson

Barrett EA, Kowalski KM [1995]. Effective hazard recognition training using a latent-image, three-dimensional slide simulation exercise. Pittsburgh, PA: U.S. Department of the Interior, Bureau of Mines, RI 9527. NTIS stock number: PB95-170379. Beus MJ, Orr TJ [1995]. Computer modeling and analysis of the Greens Creek Mine, Admiralty Island, AK. Spokane, WA: U.S. Department of the Interior, Bureau of Mines, RI9530. NTIS stock number: PB95-176418. [ ]

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

Provide exhaust face ventilation to remotely-controlled continuous mining machines making extended advances without exposing workers to unsupported roof. Approach Modify the sprayfan to move additional air to and from the coal mine face. Unmodified, sprayfans are capable of ventilating the face with 20-foot brattice setbacks. Additional sprays on the rear of the mining machine allow setbacks to be extended up to 40 feet.

Jan 1, 1988

By L. A. Johnson

The Bureau of Mines analyzed three cores from the south Seep Ridge area of the P. R. Spring tar sand deposit of northeastern Utah. Four tar sand zones are indicated in the area. The zones range in average thickness from 13 to 24 ft. The total net thickness of the tar sand in the three coreholes ranges from 71 to 112 ft. The tar sand occurs between the depths of 27 and 254 ft. It has good porosity, 25.6 pct of bulk volume; high permeability before and after oil extraction, 819 and 2,218 md, respectively; but a relatively low oil saturation, 36.5 pct of pore volume. Gravity of the oil ranges from 8.20 to 16.5° API.

Jan 1, 1975

To reduce air be respirable dust generated from emptying dry dust collectors on small truck-mounted drills used at surface coal mines.

Jan 1, 1995

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

By R. A. Friedel

Data on compositions of natural substances are important in the study of possible interrelationships. The similarity of the low molecular weight alkane isomers from crude oil and Fischer-Tropsch catalytic synthesis product has been reported (8).3 A similar composition for the alkane isomers from high-temperature coal carbonization has been found. The composition of the C4 to C 7 alkane isomers from these three sources can be calculated quantitatively with the equations previously developed to calculate alkane isomers in Fischer-Tropsch product. An KM sting reversal of the concentrations of the monomethyl isomers from C6(2 Me > 3 Me) to C7 (3 Me > 2 Me) occurs in all three products; fragmentary comparisons at higher carbon numbers indicate some dissimilarities. Naphthene isomers in the C6 to C7 range for crude oil and high-temperature coal carbonization also have similar compositions. Aliphatic hydrocarbons from low-temperature coal carbonization processes are considerably different, consisting mainly of normal alkanes.

Jan 1, 1968

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972