Search Documents

By T. O. Llewellyn

The Bureau of Mines conducted laboratory batch beneficiation tests on a waste granite sludge from New Hampshire to determine the feasibility of recovering a reusable silicon carbide product. The granite sludge responded to attrition scrubbing, desliming, and flotation in either alkaline or acid circuits using fatty acid as a collector. Recovery of over 80 percent of the contained silicon carbide at grades of up to 96 percent SiC was obtained.

Jan 1, 1975

By R. L. Montgomery

The heats of solution of erbium chloride in water and in hydrochloric acid and of erbium oxide in hydrochloric acid were determined. The results reveal a discrepancy of 10.5 kcal. per gram-atom between the heats of combustion and solution of erbium reported in the literature, the heat of combustion being more negative. The heat of combustion of erbium t4)4 and its heat of solution in hydrochloric acid (1, 18) have been reported in the literature. The heat of solution of erbium chloride was determined in two studies (2, 19). The present work was undertaken to check the reported heats of solution of erbium chloride and to determine the heat of solution of erbium oxide in hydrochloric acid. The latter quantity permits the heats of combustion and solution of erbium to be compared for mutual consistency. It was also desired to determine the degree of similarity between the thermochemistry of yttrium and erbium.

Jan 1, 1961

By A. L. Johnson

In this Bureau of Mines report, time-resolved infrared emission spectra and corresponding pressure and temperature histories are reported for large-scale propagations of CH4-air, CH4-air-N2, and CH4-air-CF3Br ignitions in a 12-ft-diam sphere. Absolute spectral radiances were obtained throughout combustion over the 1.6- to 4.8-gym range, and the radiance growth patterns for the H20 (2.5-µm) bands are presented as a function of methane stoichiometry and diluent concentration. Flame temperatures were determined from the C02-band emissions, which approximated unit emissivity shortly after ignition. Burning velocities are also given for some of the test-mixture compositions. Measured flame temperatures were in excellent to fair agreement with theoretical adiabatic values for the CH.-air and CH4-air-N2 mixtures; the best agreement was for the stoichiometric CH4-air mixture. The CH4-air-CF3Br mixtures with =2 pct CF3Br gave poor agreement with theory. The measured temperatures were significantly lower during the early stage of combustion; furthermore, the later stage of combustion was uninhibited and yielded unexpectedly high pressures. Supplemental data from a 2-ft-diam sphere at various initial pressures confirmed that the CF3Br inhibition effectiveness decreases with increased pressure. The possible effects of buoyancy, turbulence, and changing kinetics are discussed.

Jan 1, 1977

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

By Clarence O. Babcock

This Bureau of Mines report presents the initial development of a two-dimensional method of analysis for inclusions in plates in which the deformed shape of an open hole and the separate structural behavior of inclusion and plate with hole are used to obtain the stresses and strains in the inclusion only. In this report the solution for a circular inclusion is presented because a direct verification of the results with previous solutions was possible. The numerical results were in exact agreement with those obtained with the equations of Sezawa and Donnell. The equations developed are less complex than those of Sezawa and more general, for a circular inclusion, than those of Donnell. Stresses and strains in the inclusion are in terms of the elastic constants of the inclusion and the plate and the biaxial stress field applied far away. The elastic constants can be all different. An important conclusion from this work is that a difference in Poisson's ratios between inclusion and plate may be as important as a difference in Young's moduli between inclusion and plate in producing the inclusion effect. Many problems in mining and rock mechanics can be treated as inclusion problems. The understanding of inclusion behavior on a physical basis should provide the solutions to some of these problems.

Jan 1, 1974

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By S. J. Page, J. A. Organiscak

Dust surveys were conducted around small truck-mounted rock drills operating at surface coal mines to assess their airborne respirable dust generation and in-service dust control methods. Of four out of seven drills sampled, respirable dust concentrations measured around the drill deck ranged from 8.68 to 95.15 mg/m with3concentrations ranging from 1.37 to 2.69 mg/m at distances 12.2 to 30.5 m downwind of these drills. The other3drills had noticeably lower respirable dust concentrations measured around the drill deck at or below 1.30 mg/m.3Rotoclone-type dry dust collectors were commonly used with dust being emitted from around the drill deck shroud, collector exhaust, and collector fines dumping. Wind speed and direction was also a factor in the dust concentrations measured on the bench. Dust control modifications were made to three rock drills to reduce their airborne dust emissions. Dust controls tested included water injection into the Rotoclone exhaust, Rotoclone exhaust extension, improved sealing of drilling deck shroud, shrouding the Rotoclone hopper dump process, and wet drilling. These control techniques showed noticeable improvement in dust concentrations measured around the drills. Finally, repositioning the drill operator showed that operator dust exposure can be improved by avoiding the dust cloud around the drill.

Jan 1, 1995

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By Douglas Pollock, John Organiscak

Water spray characteristics, including droplet size and velocity, airborne dust capture potential, and induced airflow quantity for various spray nozzle designs were evaluated to provide basic information for improving spray applications. Water droplet size and velocity characteristics were initially measured by a Phase Doppler Particle Analyzer (PDPA) for hollow cone, full cone, flat fan, and air atomized spray nozzles at similar operating parameters. Airflow inducement and dust capture experiments were also conducted under the same operating parameters to examine any salient features of the spray nozzle type, droplet characteristics, induced airflow, and airborne dust capture. Test results indicate that there are trade offs between airflow inducement and dust capture efficiency. A spray nozzle with a wider discharge angle was observed to induce more airflow, but at reduced dust capture efficiencies. Increasing spray nozzle fluid pressure(s) generally reduced water droplet sizes with concurrent increases in droplet velocity, airflow inducement, and airborne dust capture. Placing a three-sided barrier around the spray nozzles normally reduced spray air induction and increased dust capture efficiency. A direct relationship between airborne dust capture efficiency and spray input power normalized per unit of airflow induced was ob- served. This information can be utilized to improve the performance of water sprays for reducing airborne dust levels.

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By B. D. Hanson

The U.S. Bureau of Mines has developed an interactive computer program which enables the user to identify the effect of cutting system changes on relative dust generation and forces for continuous miner drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. One or more of these parameters may be changed to determine their individual or collective effect on relative dust generation and cutting forces. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs.

Jan 1, 1989