Search Documents

By William A. Vogely

STRIKES in the steel and copper industries adversely affected production in the minerals industry in 1959. Because of an excellent first half of the year and rapid recovery of production after the steel settlement, most statistical indicators were higher than the recession-recovery year 1958. Domestic production of metals declined by 9 percent, but nonmetals (except fuels) increased by 8 percent. Ferrous-metal mine production was down 8 percent, and base-metal mine production was off 11 percent. Employment was high during the first half of the year, but averaged lower than in 1958. Stocks continued to decline as a whole, but crude metal ore stocks actually increased. The indexes of stocks at yearend were still high as compared with 1955. Prices were firm throughout the year. A new index of average unit mine value is presented for the first time in this review; it showed a very slight decline in average mine realization for 1959. The percentage share of supply from imports increased in some commodities, due in large part to the shutdown of domestic iron, steel, and copper industries.

Jan 1, 1960

By A. Z. Dimitroff, A. C. Moschetti

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jun 23, 1964

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By D. E. Seizinger

The Bureau of Mines has developed analytical methods, primarily gas chromatographic, for measurement of exhaust oxygenates produced from selected simple fuels. The resulting data were used to estimate levels of carbonyls and noncarbonyl oxygenates in exhaust from gasoline fuels. Estimated noncarbonyl oxygenates in gasoline exhaust may comprise as much as 30 pct of total oxygenates which include unsaturated carbonyls and noncarbonyls believed to be significant potential pollutants.

Jan 1, 1972

By Ronald D. Hill, Elmore C. Grim

Some of the terms defined here are not used in the text. However, the terms will be useful to those interested in this and other publications in the field of coal surface mining.

Jan 1, 1974

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By Kenneth H. Johnston

Information on oil and water production, volume of water injected, core analyses, and well completion data was collected on 28 Red Fork sand water-flood projects for comparison and evaluation of results. An average water injection efficiency of 35 percent, an average water-injected to oil-produced ratio of 16.8:1, and an average loss outside the flood pattern of approximately 45 percent of the injected fluid resulted in an oil recovery to January 1, 1969, of only 5.6 percent of the pore volume, or 9.1 percent of the initial stock-tank oil in place. The principal causes of poor oil recovery from these projects are the losses of large quantities of injection water from the flood patterns through oriented, natural fracture systems or zones of high permeability and excessive channeling of injection fluids from input wells to oil wells. For more efficient operation and a higher percentage of oil recovery from the Red Fork sand and other low-permeability-sand waterflood projects, directional orientation of both induced-and natural-fracture systems should be determined during early development. The success of a low-permeability-sand waterflood project depends to a large extent upon the orientation of the injection wells with the fracture system.

Jan 1, 1970

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

By J. E. Zeilinger

This Bureau of Mines study was conducted to determine the sulfur reduction potential attainable when washing fine-size coal on a spiral concentrator. Crushed samples of Middle Kittanning and Bakerstown bed coals washed on the spiral provided pyritic sulfur reductions of up to 90 percent for the plus 200-mesh material. Pyritic sulfur reductions on the minus 200-mesh material seldom exceeded 30 percent; consequently, this material would require further treatment. The capacity of the spiral was 2 tph per unit when washing l4-mesh by 0 coal. The ability to remove pyrite combined with the higher-than-expected capacity makes the spiral worthy of consideration as a rougher-cleaner in new fine-coal desulfurization circuits.

Jan 1, 1976

By B. W. Jong

As part of the Bureau of Mines program to develop substitute or improved performance refractory materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives on sintering and strength properties of aialon (silicon aluminum oxynitride) compositions fabricated by a conventional powder metallurgy technique. Additions of Y203, Gd203, CeO2, MgO, ZrO2, ZrSiO4, and MgA12O4 to a sialon composition containing 70 pct ß-Si3N4 + 30 pct a-A1203 increased sintered densities by as much as 50 pct over densities of undoped material. The studies also indicated that sintered densities reached a maximum between 20 and 30 mole-pct a-A1203 when a series of sialon compositions of a-Si3N4, having 6.7 to 57.9 pet a-Al203, were doped with Y203, Gd2O3, and MgO. In studies to establish the effect of the crystalline phase of the silicon nitride and alumina used, tests were made using a- and ß-Si3N4 and a- and ?-A12 03 as starting materials. The tests indicated that when using an addition of 5 wt-pct Y203, best results were obtained with a sialon composed of 74.4 mole-pct a-Si304 and 25.6 mole-pct ?-A1203. In other tests made with this sialon composition MOR values of 28,120 and 29,500 psi at 25° C, and 23,520 and 16,850 psi at 1,400° C, were obtained when doping with 5 wt-pct ZrSiO4 and ZrO2, respectively.

Jan 1, 1980

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By T. T. Campbell

This report describes the development of new electroplating baths from which tin-nickel alloy plate was deposited. Although tin-nickel plate can be deposited from an aqueous ammonium bifluoride bath, the corrosive nature of this bath has served as a deterrent to its use. The Bureau of Mines felt that more general acceptance of this new alloy plate would follow if neutral or alkaline baths could be developed. Promising results were obtained from electrolytes containing both tin and nickel chlorides dissolved in triethanolamine-hydrochloric acid or in ethylene glycol hydrochloric acid baths. Current efficiencies close to 100 percent were obtained with these baths. Research revealed that tin-nickel plate could be produced from organic solvents or from mixed aqueous-organic electrolytes. The composition of the alloy deposit - 65 percent tin and 35 percent nickel - was found to exhibit the same single-phase structure that is obtained from the commercially accepted fluoride-type bath.

Jan 1, 1959

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 6 Automatic Elevator Control Systems An automatic elevator control system, consisting of position sensing devices and a control unit, can be used to control an emergency mine hoist. While automatic elevator control systems are assembled from standard components, they are typically custom designed to suit a given customer's application. Various manufacturers contacted indicated that the price range, less installation, for a simple two-stop control system begins at approximately $2500 and can increase depending upon the type of components used, shaft depth, the type of mechanical drive used, and the maximum operating speed A partial list of elevator control manufacturers follows. They should be contacted for further details. Marshall Elevator Company Pittsburgh, P A 412 -431 -1340 Armor Elevator Company, Inc. Louisville, KY 502-361 -7181

Jan 1, 1976

By Kenneth H. Johnston

Information and data necessary for research on improving methods of oil recovery from low-permeability reservoirs and for comparison and evaluation of performance of such reservoirs with those producing from more permeable sands were obtained. Core analyses, well logs, production tests, well stimulation techniques, primary and secondary production records, and data on two water-flood projects were examined for wells producing from the Bartlesville sand, West Avant field, Osage County, Okla. Overall recovery from the study area was generally poor with only 9.0 percent of the pore volume recovered to January 1, 1968. Larger fracture treatments (8,000 to 12,000 gal) could have resulted in an increase in primary oil recovery. Secondary recovery by water-flooding accounted for only 1.9 percent of the pore volume because of the inability to control the large volume of injection fluid that escaped from the flood patterns and the excessive volumes of water produced with the oil. Future waterflood development in other low-permeability reservoirs should include the drilling of new input wells, use of injectivity surveys to locate possible natural fracture systems, or zones of high permeability, and control of injection fluids by altering flood patterns and/or plugging of the more permeable zones.

Jan 1, 1968

By Joseph J. Wallace

1. The Pocahontas No. 3 and Pocahontas No. 6 ere the two most important beds in Mercer County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 188 million short tons as of January l, 1953. Of this total, 80 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By William L. Rice

Geochemical humus sampling techniques were used by the Bureau of Mines in investigating a potential large, low-grade gold deposit in the Orogrande district, Idaho. Conifer needle humus samples were processed by ashing and fire assay-atomic absorption analysis. An area bearing anomalous concentra¬tions of gold and silver was outlined by the geochemical method.

Jan 1, 1970

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

By Joan T. May

Anhydrous methods were tested for the extraction of beryllium from low-grade source materials. The purpose of the investigations was to find new extraction processes that are applicable to domestic ores. Beryl, helvite, and phenacite materials containing from 0.1 to 2.8 percent BeO were used as starting materials for direct halogenation tests and pretreatment followed by halogenation. The results of the investigations showed that direct fluorination and carbide-chlorination are two practicable methods that can be applied to low-grade concentrates. Treatment of concentrate-carbon mixtures with anhydrous hydrogen fluoride extracted 99 percent of the beryllium in the concentrate; the soluble fluoride product, converted to an oxide, contained 70 percent BeO. Chlorination of beryllium-silicon carbide, prepared from low-grade concentrates, extracted beryllium into the volatile chloride product.

Jan 1, 1962