Search Documents

The latest Active List of Permissible Explosives and Blasting Devices was published in July, 1929, as Bureau of Mines Report of Investigations 2947, 2 under the title or "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1929.' Subsequent Reports of Investigations 2253, 2958, 2962, 2972, 2988, 2992 and 3000, were issued to record the official actions taken during July, August, September, October, 1929, and January, February, and March, 1930. No changes were made during November and December, 1929, and April, 1930. The following additional changes in the list recording the actions taken during May, 1930, are now authorized. [ ]

Jan 1, 1930

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By Foster Fraas

A method is presented for the linear evaluation of adsorption data using the equations dC = Ae-rv dv and v = [jT] - q, where dC is the phase composition increment, v a calculated parameter, T the absolute temperature, and A, r, h, g, and q the constants. The value of v is calculated from the composition C for both the adsorption surface and the immersion phase. A plot of v for each phase on Cartesian coordinates results in straight line graphs. With temperature variation, a plot of v versus,[ ] also results in straight line graphs. The equations are applicable to electronic and salt equilibria.

Jan 1, 1962

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By P. W. Jeran, C. M. McCulloch, Maurice Deul

The natural vertical fracture sys tem in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north- western West Virginia to N 57° W in southwestern Pennsylvania ; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures . Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By Oliver C. Fursman

The Bureau of Mines undertook this investigation to study methods of utilizing red mud residues from production of alumina from bauxite. Pilot-plant tests were conducted using Jamaican and Surinam red muds. Both the carbon-lime-soda sinter process and electric-arc smelting with coke and limestone were employed to recover iron and alumina. Alumina recoveries of 85 to 90 percent were obtained by the sinter process; although iron recovery was about 80 percent, the magnetic product was finely divided and difficult to separate from the gangue. Smelting red muds in the electric-arc furnace produced a pig iron with 98-percent recovery of iron; up to 84 percent of the A1203 was recovered by leaching the calcium aluminate slag with Na2C03 solution. A titania product assaying 96 percent TiO2 was recovered from the nonmagnetic portion of Surinam red mud sinter by extraction with H2SO4. Leached calcium aluminate slags and brown mud (from the combination Bayer process) are possible raw materials in the manufacture of portland cement.

Jan 1, 1970

By Edward F. Courtney

Loss of life, loss of sight, crippling injuries, and property damage nearly always result from accidents involving explosives. The severity of such accidents has prompted lawmaking bodies to pass laws concerning the transportation, handling, and use of explosives; manufacturers of explosives publish manuals 'describing explosives and practical methods of handling then; and mining companies and others who use large quantities of explosives publish rules based on actual experience for the guidance of their employees. Careless storage of explosives by thoughtless or incompetent persons, particularly if they are left where children or saboteurs have access 'to them, has led to many serious accidents. Many contractors and mining operators who use explosives are extremely careless about storing them. It is the purpose of this paper to discuss the explosive-handling practices of a large western mining company, which are considered better than most.

Jan 1, 1946

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By A. J. Farstad

The use of radio signals for underground communications was considered as early as the mid-1920's [1] - [4] . However, early experiments did not produce promising results with the type of equipment that was available then [5] . With advancements in solid state technology many of the schemes considered impractical in the early days suddenly became practical. The properties of electromagnetic wave behavior in conducting media have been intensively studied by Wait [ 6] and others and can be utilized not only in communication with trapped miners, but also as a means of locating their position. This report deals with the development of portable electromagnetic equipment, powered by the miner's conventional lamp battery, which can be used to alert surface rescue personnel of the trapped miner Is location. The Westinghouse Georesearch Laboratory (WGL) under BUMINES sponsors hip initially approached the trapped miner location problem using seismic techniques. It was learned from this effort that two serious shortcomings of seismic techniques are (1) the extremely weak signals available on the surface from miner generated hammer blows, requiring long processing times at the surface receiver, and (2) the relatively slow procedure of deploying geophone arrays to sense the seismic uplink signals. By contrast, the electromagnetic techniques have proven much more practical from a deployment time standpoint and in most cases have also proven to be more accurate in determining location. Furthermore, these techniques have been successfully tested using a receiver in a heli- copter for reconnaissance purposes. However, before any electromagnetic location technique can become fully operational, the miners themselves must be equipped with emergency transmitters to be carried with them on each work shift. Consequently, much emphasis has been placed on the development of extremely lightweight transmitting equipment. The performance of some of the electromagnetic location equipment developed by Westinghouse will be described in the following sections. 2.0 Basic Concepts Theoretical concepts for locating magnetic dipoles in the earth have been treated by Wait [ 7] and Olsen [ 8] . A generalized curve for the attenuation of magnetic fields in a conducting half-space is derived from

Jan 1, 1973

By J. E. Hamak

This publication contains analyses and related source data for 165 natural gas samples from 21 States and 1 foreign country. Of the total samples, 155 were collected during calendar year 1988. The remainder were collected earlier, but releases granting permission to publish were not received until 1988. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1989

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

[ ]

Jan 1, 2012

By C. M. McCulloch

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006