Search Documents

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By D. R. Tesarik, M. K. Larson, D. K. Denton, J. B. Seymour, R. L. Rains, T. J. Williams

Because backfill has occasionally collapsed into an active working area, posing a hazard to miners, engineers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and Hecla Mining Co. installed instruments in a cemented, backfilled, stope-ramp intersection at Hecla’s Lucky Friday Mine, Mullan, ID. The purpose was to measure stress and strain changes in the backfill and reinforcing members during undercut mining. The instruments were monitored for 6 months while three successive cuts were mined below the intersection. Readings showed induced loads up to 3450 kPa (500 psi) in the backfill as stope walls converged 2.5 to 12 cm (1 to 5 in). The backfill then deformed against the top and bottom plates of the 2-m- (6-ft-) long vertical rock bolts installed as reinforcement, producing loads to 177 kN (40,000 lb)on the rock bolts. We hypothesize that a compressive zone was created in the backfill that allowed the backfill to remain stable as long as the compressive zones from adjacent rock bolts overlapped. This hypothesis is presented in graphical form. Of particular interest was the effect of loading on trusses installed to augment the vertical rock bolts and wire mesh typically installed in backfill. Data from the instruments indicate that wall closure perpendicular to the vein induced loads in truss legs parallel to the vein and in the rock bolt driven through the center of the truss, but, because they are designed to function under tension, truss legs perpendicular to the vein supplied in significant support as a result of compressional forces from wall closure. Based on this study, use of trusses was discontinued, and an alternative support system of wood beams and posts was installed as needed to ensure the safety of miners working beneath the backfill in stope-ramp intersections.

Jan 7, 2001

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By Everett A. Sondreal

Data are presented on the characteristics of lignites with emphasis on the composition and fusion properties of the ash. Differences in the analyses of commercial-grade lignites are related primarily to variations in moisture and ash contents. Lignite ash is generally characterized by high concentra¬tions of alkaline earth oxides and a greater tendency for retention of sulfur in the ash than higher-rank coals. Composition of ash varies significantly within and between mines. The differences within mines are significant for short distances and may be eliminated under certain circumstances by normal mixing occurring during mining. The sulfur in lignite averages 0.6 percent and is found primarily in the organic or pyritic forms with only a trace of the sulfate. During the stan¬dard laboratory asking procedures, from 60 to 100 percent of the original sul¬fur is retained in the lignite ash. Trace elements, such as uranium and germanium, in the ash from commercial¬-grade lignites are present in low concentrations, but others, primarily copper and silver, are present in specific samples in concentrations approaching those found in some commercial ores.

Jan 1, 1968

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society's interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By R. E. Hall

When the criterion for control of scale prevention on the evaporating surfaces is made the conditions in the concentrated boiler water, then this control becomes an exact operation amenable to an accuracy commensurate with all other operations in the boiler room. The responsibility in boiler water conditioning, however, includes more than clean surfaces. Corrosion in feed lines, economizers and the boiler is a function of the condition of the later, and must be controlled. Steam line and turbine blading deposits must be obviated by the system of conditioning. By the chemical treatment employed, the amount and character of noncondensable uses in the steam must be controlled in accordance with the intended use of the steam. All. in all, the responsibility in boiler crater conditioning ends not with the entrance of the water into the boiler but with the passage from the boiler nozzle of steam, the dryness and rarity of which are defined by the uses to be made thereof. A clearer conception of the scope of boiler water conditioning can be obtained by reference to a diagram of the surfaces (Figure 1) at which it functions. Consideration of this diagram leads to the following outline for the problems of boiler water conditioning: (a) Prevention of scale formation on surfaces (1) In contact with water but at which no evaporation occurs. (2) At which evaporation is occurring.

Jan 1, 1926

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By E. L. Rawlins

Pipe lines through which natural gas is flowing should be buried in order to minimize fluctuations in the temperature of the gas, as these fluctuations have several harmful effects. One of these effects is to decrease the accuracy of measurements of gas volume. In order to meter properly the quantity of gas flowing past any point in a transmission system, it is necessary to how the temperature of the gas. If the temperature remains fairly constant, the gas flow can be measured with a close degree of accuracy, but if it fluctuates rapidly, close measurement is impossible.

Jan 1, 1926

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals? and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the ?Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1981

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978