Search Documents

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By D. E. Shanks

As part of its program to lessen dependence on foreign bauxite as the Nation's primary source of cell-grade alumina, the Bureau of Mines is investigating sulfuric acid (H2S04) leaching procedures for the recovery of alumina from domestic aluminous materials. The successful application of a H2S04 leaching process depends on the recovery of the aluminum values in an easily washed and filtered form, containing a minimum of water to be driven off in the subsequent calcination step. This goal was met by the high-temperature hydrolysis of simulated aluminum sulfate [A12(S04)3] leach liquor. Crystalline, insoluble aluminum hydroxy sulfate [A1(OH)S04], which had a water-to-alumina mole ratio of 1:1, was produced. Eighty-six percent of a solution containing 127 g of A12(S04)3 per liter and 76 pct of a solution containing 336 g of A12(S04)3 per liter were hydrolyzed to insoluble aluminum hydroxy sulfate by autoclaving for 1 hr at 320° C and rapidly quenching to room temperature. Higher operating temperatures were precluded by corrosion of the autoclave. The yield of aluminum in the hydrolysis product increased with increasing hydrolysis temperature and decreasing A12(S04)3 concentration.

Jan 1, 1981

By D. M. Lewis, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, J. H. Kang, V. Castronova

"Tetrandrine is a bisbenzylisoquinoline alkaloid which has been shown to exhibit antifibrotic activity against silicosis. Tetrandrine is characterized by its strong binding to alveolar macrophages and inhibition of particle-induced respiratory burst activity in these phagocytes. In contrast, tubocurine and tubocurarine are structurally similar to tetrandrine but exhibit little effect on fibrosis or activation of alveolar macrophages. The objective of the present study was to test the effect of tetrandrine on macrophage production of monokines in response to occupational dusts, and to determine tetrandrine's effect on monokine-medicated cell growth using a mouse thymocyte proliferation assay and lipopolysaccharide (LPS) as a positive control. Stimulation of alveolar macrophages by respirable silica dust resulted in a release of monokines which caused a fourfold increase in thymocyte proliferation. Coal dust, on the other hand, had no effect on macrophage production of this cytokine. Tetrandrine was found to exhibit a dose-dependent inhibition of monokine release from both silica and LPS-stimulated alveolar macrophages. In experiments where thymocytes were directly treated with tetrandrine, a dose-dependent inhibition of thymocyte proliferation was noted with both interleukin-1- (IL-1) specific and nonspecific mitogenic (concanavalin A) actions. In contrast to the inhibitory potency of tetrandrine, tubocurarine was found to have no effect on either the production of monokines by LPS-stimulated alveolar macrophages or IL-I-mediated thymocyte proliferation. These results provide a correlation between the ant:fibrotic effect of tetrandrine and inhibition of macrophage activation. INTRODUCTIONThe pathogenesis of chronic pulmonary fibrosis caused by inhalation of occupational dusts has been associated with abnormal activation of alveolar macrophages such as the release of various cytokines capable of inducing fibroblast proliferation and collagen synthesis. These macrophage-derived cytokines include interleukin-1 (IL-1), tumor necrosis factor (TNF), platelet-derived growth factor (PDGF), transforming growth factor-B (TGF-(B), macrophage derived growth factor (MDGF), and interferon [1, 2].Interleukin-1 is a major macrophage-derived cytokine that has been shown to exhibit multiple biological effects on a variety of target cells. It is known to cause leukocyte [3, 4] and endothelial cell activation [5, 6], and to affect the synthesis and maintenance of the extracellular matrix by stimulation of fibroblast proliferation [7-9], synthesis of collagens [10] and gluco-saminoglycans [11], and prostaglandin E2 production [12]. In addition, IL-1 plays an important role in the initiation of an immune response through its direct activation of lymphocytes and stimulation of the production of other cytokines, such as interferons and hemopoietic colony-stimulating factors, needed for the expression of an immune response [13]. As a major cytokine in the immune-inflammatory sequela, IL-1 is also produced by epidermal, epithelial, lymphoid, and vascular tissues after infection, injury, or antigenic challenge [14]. Agents such as lipopolysaccharide (LPS), phorbol myristate acetate (PMA), immune complexes, and particulates are known to activate the synthesis and release of IL-1 by monocytes and macrophages [15]. These substances also trigger intracellular signals leading to altered arachidonic acid metabolism. Although the mechanism is still not clear, prostaglandins have been shown to suppress IL-1 translation via the induction of cyclic adenosine-monophosphate (CAMP), whereas leukotrienes produce a positive signal for IL-1 production [13]."

Mar 1, 1992

By J. B. Gayle

Both immediate and long-range economic factors are associated with blending anthrafines to produce metallurgical cokes, and they warrant careful consideration of the technology of carbonization of blends containing significant proportions of inert substances in general and anthrafines in particular. This situation has resulted in numerous publications dealing with various phases of the overall problem, particular emphasis being placed on the effects of inert substances on the yields and quality of cokes produced. Because relatively little attention has been given to the expansion behavior of coal blends containing inert substances, an investigation of this problem was undertaken using the Bureau of Mines sole-heated oven. Since experiments in the sole-heated oven do not measure wall pressures directly, a new method of interpretation of sole-heated oven data, which permits estimates of wall pressures, has been proposed.

Jan 1, 1955

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By G. S. Rice, H. P. Greenwald

"Experience and experiment have goth shown that a cloud of coal-dust in air can be inflamed and an explosion developed only when a certain minimum concentration of the dust in air has been equaled or exceeded. Those who have had experience in the handling of coal know that dust is frequently present in the air and may be of sufficient density to obscure an ordinary electric light at a distance of 40 or 50 feet; yet flames may be, and times without number have been, introduced into such clouds, when no additional coal-dust has been stirred up, with no effect other than the burning of the dust particles which actually enter flame. Evidently the density of the dust cloud is insufficient to give self-supporting combustion.The minimum amount of dust in air required to give a spreading flame will vary with a number of factors such as the composition of the dust and its size. This amount in a unit space may be considered analogous to the lower limit of inflammability of fire damp (methane) in air, although the variation in limit of explosibility of gas is small even when conditions of the experiment are altered. In large-scale determinations of the lower limit of inflammability of coal-dust there is no certain method by which a sample of the dust cloud can be snatched and its density determined. It is necessary to produce the best possible dust cloud from a known weight of dust, in a known volume and assume - probably with considerable error - that the dust cloud is reasonably uniform. The dust cloud must be formed and the source of ignition applied to it simultaneously; this is generally accomplished by the use of blow-out shots of black blasting powder, dynamite, or similar explosive so prepared as to blow out like a cannon shot, or by a gas explosion. The more violence attending the source of ignition, the greater is the probability that all the dust is raised in a uniform cloud; and the greater the length or intensity of the flame, the greater are the chances of ignition. As a result one may obtain a variation in apparent minimum density with different sources of ignition. This difference is more apparent than real and must remain until devices for instantaneous sampling of dust clouds during explosions are perfected."

Aug 1, 1931

By M. J. Ankeny

This is a study of 58 fatal haulage accidents investigated by Federal coal-mine inspectors during the period January - June 1951. The information presented in this circular was obtained by analyzing fatal haulage accidents in 33 bituminous-coal producing counties representing 11 States. The physical conditions represent a cross section off producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of large modern mechanized operations. These data are thought to be representative of haulage conditions within the bituminous-coal mining industry and are submitted to follow up the Information Circular 7604 ?Analysis of Haulage Fatalities in Bituminous-Coal Mines - 1950.? Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the problem of haulage safety is complex. It is subject to constant change and is comprised of numerous influencing variables, which are not always obvious. The solution to this problem will not come through the application of any standard formula or mechanical approach since the inherent factors are strongly influenced by the human equation, and the chain of circumstances is further affected by expediency.

Jan 1, 1951

By David C. Scott

Between 1990 and 1991, the Bureau of Mines studied the mineral resources of the Kaibab National Forest to appraise the resources present and to determine the types of deposits, and their location. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. Small amounts of copper with lesser amounts of gold and silver have been produced from limestone-hosted, strata-bound deposits in the North Kaibab and Tusayan Ranger Districts. In addition to these small metallic deposits, volcanic cinders, pumice, flagstone, and sand and gravel have been quarried in the Chalendar and Williams Ranger Districts. At least ten uranium-mineralized breccia pipes have been identified in the Tusayan Ranger District, One of these, the Canyon pipe, contains a high-grade uranium ore body with associated silver, copper, lead, vanadium, and zinc. The mine permit for the Canyon pipe has been approved and the mine shaft head frame erected.

Jan 1, 1992

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"An electro-optical method was used to quantify superoxide (SO) release from single rat pulmonary alveolar macrophages (PAM) exposed in vitro to respirable quartz and kaolin dusts and in vivo to quartz. Release was determined by measuring the reduction of nitroblue tdrazolium (NBT) to a diformazan precipitate at 550 nm from video-recorded images of individual cells. In vitro exposure to 0.025 or 0.05 mg/ml kaolin for 40 minutes resulted in no significant differences in either the total diformazan produced (max) or the maximum rate of diformazan production (R)./n vitro exposure to 0.025 mg/ml c1uartz decreased max 38 percent while no significant change was found using 0.05 mg/ml. However, R was decreased 31 percent and 24 percent for the low and high dose, respectively. In contrast, PAM obtained from animals exposed in vivo to quartz dust for two or four weeks in inhalation chambers exhibited increased production of diformazan. However, only PAM analyzed three days post-exposure showed significant increases, while PAM from animals sacrificed ten or 31 days post-exposure were not significantly different from control. The combined in vitro and in vivo quartz results might suggest that there is an initital acute response to exposure that decreases the ability of PAM to produce SO, followed by recruitment of production of PAM with increased SO producing capability. It appears that removal of animals from the source of exposure permits PAM to return to control levels of SO production by31 days. Whether this would be true for chronic exposure remains to be elucidated.IntroductionPulmonary alveolar macrophages (PAM) protect the lungs by phagocytizing foreign debris and bacteria.(1) This process involves ingestion as well as destruction of foreign matter. Phagocytosis usually is accompanied by a respiratory burst which increases cellular oxygen consumption leading to the release of highly reactive oxygen metabolites.(2) These agents have been implicated in the killing of bacteria by phagocytes, but they have also been shown to be toxic and,have been linked to cancer, emphysema, arthritis, diabetes, and other diseases.(3) Toxic effects may be a result of 1) an abnormally low production of metabolites, resulting in damage to lung tissue by the respired bacteria and/or dusts; or 2) an abnormally high production resulting in direct damage to lung tissue by metabolites themselves."

Mar 1, 1989

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921

By Earl C. Lane

The Bureau of Mines is making a survey of petroleum products manufactured on the Pacific Coast from California crude oils . California crude petroleum is known to differ in some characteristics from the crude oil produced in other parts of the United States , and the claim has been made that the present Federal specifications are unduly severe when applied to the products made from California crudes . The main purpose of the present survey is to determine whether these claims are justified . This report deals only with California gasolines . Other products , such as burning oil , fuel and lubricating oils , will be taken up later . The samples reported were furnished in most cases , by the four large refining companies located on the Pacific Coast , although a number of samples of motor gasoline were purchased in the open market . In Los Angeles , samples of motor gasoline were obtained from service stations representing as many different refineries as possible . Inasmuch as San Francisco is one of the cities covered by the regular semi -annual motor gasoline survey conducted by the Bureau of Mines , it was not considered essential that the set of samples obtained from this city be as comprehensive as would otherwise have been necessary . The gasoline consumed in the States of Washington and Oregon is furnished for the most part by California refineries , and no effort was made to procure samples from these States .

Apr 1, 1922

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By D. C. Dahlin

The Bureau of Mines investigated the Ketchem Dome tin prospect in east-central Alaska to evaluate the tin resource. The studies included field investigations, mineralogical characterization, and concentration of the tin-bearing minerals. The tin mineralization consists of cassiterite (Sn02), which occurs as grains disseminated in a greisen (quartz-mica) matrixo A bulk sample from the largest and best-developed greisen vein exposed at Ketchem Dome contained 0.51 pct Sn. Concentration of the cassiterite by gravity table methods resulted in a product that contained 56 pct of the tin at a grade of 41.4 pct Sn. The mineralization exposed at Ketchem Dome is typical of greisen found in the area and elsewhere in interior Alaska.

Jan 1, 1987