Search Documents

By G. L. Hopps

Various chemicals, including compounds of copper and lead, were added to a mixture of No. 2 and No. 6 fuel oils that was fired in an experimental furnace. Tests were made to determine (1) the effectiveness of these chemicals in removing soot deposits on probes devised to simulate heat-transfer surfaces in boilers and (2) the effectiveness of the chemicals in preventing the deposition of soot on the probe surface. Test conditions were regulated so that the temperature of the products of combustion adjacent to the probes was in the range of 625° to 700° F. The clean-metal temperatures of the air-cooled probes were comparable with the water-tube temperatures in boilers operated at 40 to 100 p.s,i.g. The dosages of the fuel oil additives used in these tests were generally larger than those usually recommended for most proprietary compounds.

Jan 1, 1962

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By L. E. Schultze

The Bureau of Mines has devised techniques to recover lithium from geothermal brines as the chloride. More than 99 pct of the lithium was precipitated from a brine containing 170 mg/L Li by adding a solution of AICl3 and increasing the pH to 7.5 with lime slurry. The Li-Al precipitate was dissolved in HCl and sparged with gaseous HCI to recover the AlCl3; this resulted in a solution containing LiCl and CaCI2. The solution was evaporated at 1000 C to obtain a mixture of the chlorides from which 97 pct of the lithium was recovered and 90 pct of the calcium was rejected by leaching with tetrahydrofuran. The LiCl recovered by evaporation of the tetrahydrofuran was purified by dissolution in water and treatment with oxalic acid. The final LiCl solution contained 89 pct of the lithium originally present in the brine and had a purity of 99.9 pet.

Jan 1, 1984

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By G. S. Scott, G. W. Jones

Trichloroethylene (CHC1CC12) is an important solvent for fats , resins , bitumens, rubber , sulfur , and phosphorus . It is used extensively in drycleaning because of its low order of combustibility and has recently been proposed as an inhalation anaesthetic . Its physical properties have been described by Carlisle and Levine . It is usually considered a noninflammable material ; however , substances that are noninflammable when mixed with air are not necessarily noninflammable when mixed with oxygen . Thus , Hewer's statement that " Trichloroethylene*** is not inflammable under any circumstances , nor will its vapor explode when mixed in any proportion with air , oxygen, or nitrous oxide , " requires qualification , especially in anesthesia, where pure oxygen may at times be substituted for air , This report gives the results of tests made to determine the inflammability of trichloroethylene in various mixtures of oxygen and nitrogen . The trichloroethylene used was Eastman's No. 1300. The boiling point was given as 86 ° to 87 °C . The specific gravity and refractive index of the sample measured in this laboratory were , respectively, 1.45 and 1.4759 at 25 °C .

Nov 1, 1942

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By Ted A. Lewtas

The effectiveness of induction fans in ventilating dead headings was studied in the laboratory and underground. The following fan attachments were evaluated: a. Aerodynamic nozzle b. Various lengths of vent tube c. Honeycomb airflow straightener. Various fan locations were also tested. The following conclusions were reached: a. A nozzle on a fan located against the drift wall gives the greatest jet penetration distance. b. Air straighteners are ineffective in increasing jet penetration. c. Induction fans are ineffective in removing contaminants from dead headings without sufficient main ventilation flow.

Jan 1, 1980

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs, at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The, cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Evans Pipe Co., Uhrichsville, Tuscarawas County, Ohio. The author wishes to acknowledge the assistance of the following company officials: T. J. Evans, II, president; T. J. Evans III, vice president and general manager; and L. P. Young, general superintendent.

Jan 1, 1936

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By S. G. McAnally

This is one of a series of papers describing mining and crushing methods and costs at cement plant quarries throughout the United States and deals directly with the methods employed and costs obtained at the Reliance quarry of the Giant Portland Cement Co. at Egypt, Pa., although it is more or less descriptive of the methods used throughout the Lehigh Valley cement district. Systems of transportation vary according to local conditions, such as proximity to the mill, depth of quarry floor with relation to the mill level, etc. Methods of prospecting differ mainly in the type f drills used. Systems of storage, crushing, and grinding vary chiefly in the types of units. ACKNOWLEDGMENTS Most of the information regarding the early history of the Lehigh cement district was obtained from the History f the Portland Cement Industry of the United States, by Robert W. Lesley, the first president of the Portland Cement Association. The writer is indebted also to Charles Clader, Giant Portland Cement Co. quarry superintendent, for valuable information regarding present and past methods and equipment.

Jan 1, 1931

By F. F. Aplan, J. A. Gutierrez-Rodriguez

"Contact-angle and flotation techniques were used to evaluate the influence of oxygen - both that inherent in the coal and that introduced by ambient temperature, aqueous oxidation - on a wide range of coal ranks. Oxidation was found to decrease the hydrophobicity and floatability of coal; with the effect being minor for coals of high rank but becoming increasingly important as the rank of coal is reduced. As an approximation, oxidation makes a coal behave as if it were one of lower rank. Frother only flotation' of coal· correlates with the captive-bubble contact angle whereas when oil is used as a collector, the flotation appears to follow the pattern shown by the water sessile drop on a fresh, un-reagentized coal surface. Coal recovery lost through oxidation may often be recovered by use of a variety of collectors, of which No. 2 foe! oil is among the best of those reagents tested. A simple alkali-extraction test may be used to estimate the influence of oxidation on coal preparation processes and use.INTRODUCTIONThe hydrophobicity of coal is not only a function of its rank but also of the extent of oxidation of the coal during and subsequent to its formation. Weathering and oxidation processes may proceed in-situ for coal deposits that outcrop near the earth's surface, or the oxidation of the coal particles may occur during mining, stockpiling or processing. Such oxidation, whether it affects the bulk-coal sample or on1y a thin outer layer on the coal surface, can dramatically influence the wettability of the particle and hence such processes as flotation, filtration, flocculation and dispersion.Many of the studies made on the oxidation of coals ·were designed to study its effect on flotation, coking or pyrolysis. The. present study 'is directed exclusively toward the effect of oxidation on the hydrophobicity and floatability of the coal. One of the first studies of the effect of oxidation on coal flotation was that of Sun [l] who found that as oxidation proceeds, coal becomes progressively more hydrophilic. Low-temperature oxidation (100-150°C for 250 h) generally lowered the coal floatability with an oily collector only slightly, but more extensive oxidation (200- 3500 C for 250 h) reduced coal floatability seriously. Sun also found that cationic amines were effective collectors for the oxidized coal which infers that oxidation makes the coal more negative in solution. He attributed the loss of floatability to be due to the accumulation of water-insoluble oxidation products at the coal surface. Gayle et al. [2] found that oxidation adversely affected coal flotation when an aliphatic-alcohol frother was used, though a small amount of oxidation appeared to improve the floatability of some coals using a kerosene-pine oil, collector-frother mixture in pilot-plant testing. Prolonged oxidation adversely affected the flotation recovery of the coals tested, the effect being more pronounced when an alcoholic-type frother only was used. They also noted that the reduction in floatability of lower rank bituminous coals was more affected by oxidation than was that of higher rank bituminous coals."

Jan 1, 1989

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By Arthur Metcalfe, Edward Thomas, A. J. Barry

"Early in 1947 the Bureau of Mines became interested in adapting suspension roof support to coal mining 5/ as a possible means of reducing the high rate of accidents from falls of roof. For a time the program made little progress be¬cause of the shortage of steel products after the end of World War II, but during the past 8 months this restriction has eased, and as of May 1, 1949, 114 mines had either started experimental work or had ordered materials and equip¬ment in anticipation of trial installations. It is estimated that 30 linear miles of roof in underground passageways have been secured by this method in recent months, and no lost-time roof-fall accident has been reported in these areas up to that date.Many coal-mining companies in widely separated localities have cooperated in making experimental installations. In very few instances are these companies entirely satisfied that they have arrived at the best solution in determining the most efficient adaptation to suit their particular conditions. Moreover, new ideas and modifications of the basic principle are constantly being brought to light and are being tested. Available test data is far from complete, and it is conceivable that some new idea will be developed to alter the present concept of proper technique; therefore, this progress report does not attempt to answer all questions that might arise in connection with this method of roof support; it simply recounts the experience acquired to date. Consequently, few references to costs are made. Up-to-date quotations on material and equipment used in suspension roof-support installations may be obtained from numerous mine-supply companies.The authors gratefully acknowledge the cooperation of mining companies whose personnel made possible collection of the information contained in this circular: Bethlehem Collieries Corp., Barrackville, W. Va.; Berwind-White Coal Mining Co., Windber, Pa.; Consolidation Coal Co., (Ky.); Jenkins, Ky.; Consolidation Coal Co. (W. Va.), Fairmont, W.Va.; Clinchfield Coal Corp., Dante, Va.; Consolidated Coal Co., St. Louis, Mo.; Hanna Coal Co., St. Clairsville, Ohio; Missouri Portland Cement Co., Sugar Creek, Mo.; Pocahontas Fuel Corp., Pocahontas, Va.; Reppert Coal Co., Dola, W. Va.; St. Joseph Lead Co., Bonne Terre, Mo.; and Tennessee Coal, Iron, & Railroad Co., Birmingham, Ala.The fundamental theory of suspension roof supports is not new; in fact, its application in the construction of beams predates mining itself. The basic principle involved is the reinforcement of roof rock with steel rods inserted in the roof and anchored therein at points where the rock is least likely to be affected by stresses resulting from mining. Such roof supports have been used in mines for many years in widely separated localities. The St. Joseph Lead Co., operating in southeastern Missouri, apparently was the first large mining company to prove the practicability of the principle by applying it in a systematic manner for securing roof for more than 20 years (fig. 1)."

Sep 1, 1949