Search Documents

By W. H. Ode, W. A. Selvig

"INTR0DUCTIONAccording to the Standard Specifications for Classification of Coals by Rank of the American Society for Testing Materials (A.S.T.M. Designation: D388-38).1/ high-volatile bituminous coals, subbituminous coals, and lignites are classified on the basis of calorific values on the ""moist"", mineral-matter-free basis. The moist basis refers to coal containing its natural bed moisture but not including visible water on the surface of the coal. It is assumed that the natural bed moisture of coal in the ground represents the moisture-holding capacity of the coal when in equilibrium with air at approximately 100 percent relative humidity. This moisture is sometimes referred to as inherent moisture as opposed to extraneous moisture, which wets the surface of the coal.To simplify procedures for determining the moisture-holding capacity of coal it is assumed, for all practical purposes that the moisture content of coal when brought to a standard condition of moisture equilibrium in an atmosphere of 97 percent relative humidity and 300 C. represents the bed moisture of the coal. The A.3.T.M. specifications provide that this condition of moisture equilibrium shall be obtained by bringing the coal to a standard condition of moisture equilibrium at 300 C. in a vacuum desiccator containing a saturated solution of potassium sulfate (97 percent relative humidity) according to the procedure proposed by Stanfield and Gilbart. 4/ No mention is made in the specifications for bringing partly air-dried samples to their natural bed moisture condition probably because of the hysteresis effect that has been noted by various investigators. 5/ In this connection it has been found from sorption studies that the adsorption and desorption curves for lignite are not entirely reversible. The hysteresis effect has been explained by some investigators as resulting from shrinkage of the lignite during drying, which causes a collapse of some of the capillaries, so the dried lignite cannot take up as much water as it held originally."

Apr 1, 1953

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By Steven J. Page

Longwall double-drum shearers frequently have difficulty complying with the 2.0 mg/m3 dust standard and, therefore, require the use of effective dust controls. However, before dust controls can be implemented effectively, the major individual dust sources must be determined and their relative severity evaluated. The Bureau of Mines has recently developed a sampling strategy, based upon short-term gravimetric sampling, that can identify the major dust sources contributing to the shearer operator's exposure. This technique utilizes approved gravimetric sampling equipment already available to all mine operators and can be performed by two people in 2 days. Five examples, including data analysis, are discussed with respect to various cutting sequences. In addition, typical dust source contributions obtained from studies of double-drum shearer operations regularly in compliance are included. Mine operators can thereby compare their dust source evaluation results with those from these longwalls.

Jan 1, 1982

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By Steven W. Schmauch

The Ruby Mountains study area encompasses 75,615 acres managed by the U.S. Bureau of Land Management in Madison County, MT. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine mineral resources. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. There are no organized mining districts and no current claims in the study area. Significantly mineralized quartz veins, shear zones, or talc bodies apparently do not exist within the study area. A small part of the Kelly Iron Deposit is inside, but dips away from the study area; the main occurrence is estimated to have 32 million tons of subeconomic resources that average 21 percent iron.

Jan 1, 1985

By A. D. Garman

This paper presents one of a series of digests of foreign mining leg- islation and court decisions which is being repared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countrics. This interpretation of the laws of Panama has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to who it is being referr ed through the courtesy of the Department of State.

Apr 1, 1930

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By Eugene V. Cilento, R. Clark Lantz, K. A. DiGregorio

"This laboratory bas developed a sensitive electro-optical method to quantify the initial rate (R) and total amount (MAX) of superoxide (02) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope-based TV system to visualize PAM in culture, and to video record the images during the time the cells produce 02. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of O2-, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin . were added to the medium (in vitro). Rand MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using which will permit PAM to be restirnulated by different dusts to help establish a dose response relation~ p and a means to study the role of lung surfactant on modifying the acute toxicity of inbaled dusts. Ultimately, this methodology should provide useful insight into establishing the role of 02 in PAM dysfunction due to inhalation of dusts, and in lung diseases such as pneumoconioses. INTRODOCTIONPAM are free cells found in the lungs which protect the lungs by removing foreign debris and bacteria. This is accomplished, in part, by the process of phagocytosis, whereby foreign matter is internalized into vesicles known as primary phagosomes. Phagocytosis also involves the chemical breakdown of inhaled dusts and the killing of microbes. Detoxification is aided by the respiratory burst, which is a metabolic response of the cell to foreign substances, that results in the production of highly reactive oxidizing agents from the partial reduction of extracellular oxygen to superoxide (02) at the surface of the plasma membrane. Superoxide undergoes either spontaneous or enzyme catalyzed dismutation reactions to form hydrogen peroxide (H202) and subsequently hydroxyl radical (OH•) and singlet oxygen (02 t ). However, while these oxygen metabolites aid in the killing of microbes they also may destroy endogenous tissue. For example, 02 has been linked to the aging process and to many diseases including emphysema, diabetes, and cancer.'' Therefore, a better understanding of the production of 02 is extremely important since an abnonnally low production could result in damage by inhaled dusts and bacteria while an abnormally high production could result in direct damage to the lung tissue by the phagocytes. Inhalation of respirable sized mineral dusts, such as quartz (silica), coal mine dusts (CMD), and asbestos, results in various pulmonary disorders. PAM are thought to play an important role since evidence suggests that the first step in fibrogenesis is an interaction of dust particles with PAM. Generally, in vivo exposure of animals to mineral dusts results in increased respiratory burst activity, migratory patterns, phagocytic behavior, and secretory potential of PAM, and for this reason these have been implicated to be pivotal events in the pathogenesis of pulmonary diseases.1 In addition to stimulation of resident PAM, an influx of monocytes into the lung and/or production of new macrophages generally occurs in response to fibrogenic dust inhalation. Further, PAM may attract and stimulate fibroblasts, which normally synthesize proteins and collagen during rep~ of tissue, by secreting chemoattractants and enzymes. Thus, PAM may be involved in pulmonary disorders through failure or partial loss of their defensive capability, or indirectly, through release of other mediators."

Jan 1, 1990

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By Robert F. Droullard

The Bureau of Mines has investigated techniques of using gross alpha or beta detectors to continuously measure working levels. Both methods measure radioactive particulates collected on a filter paper using a constant airflow. Inherent-error studies indicate a value of about ±3 percent for the gross alpha method and about ±8 percent for the beta method in typical mine atmospheres. However, the beta method avoids problems associated with alpha detectors and is therefore more useful. Applications of these continuous working-level detectors include work area monitoring of exposure levels in underground openings, such as mines and caves, and calibrating personal dosimeters exposed over extended time intervals.

Jan 1, 1977

By RUSSELL S. DAVIES, Andrew Allan, John W. Buch

This is a progress report for the period February 1, 1949, to August 15, 1949, covering experiments with lightweight shearing machines for developing thin, steeply pitching anthracite beds. The over-all objective at the time an underground test section was established on July 30, 1946, was to improve mining above the gangway by developing methods for mechanization of pitch mining. Following the preliminary cutting tests in the gangway with the German machines, it became evident that the use of machines of this type indicated advantages for development work that could not be overlooked and warranted investigation. An agreement was reached with the cooperating company that this be done. Thus, the objectivo in the period covered by this report has been to obtain operating data to uso in comparing hand and machine methods of driving development openings. In obtaining the machine-mining data, 78 feet of gangway, 108 feet of heading, and 80 foot of chute work were driven. Hand-mining data are authentic for the mining condition. It has been shown that full mechanization is two and one-half times as fast as conventional hand methods on a lineal-feet- advance-per-shift basis and costs but little more than one-third as much. Tho machines are air-powered; there is less shattering of the coal bed by blasting; water sprays are used to allay' dust; coal is loaded by machine; no rock is taken; timber is not dislodgod by heavy blasting charges; and it may be said, except for the development of a means for transporting timber to the face, that the tasks for the miner are less arduous, and the working face equally as safe, or safer, than in driving by hand. Face timbering remains the greatest time- consuming cycle item, and steps are being taken to correct this. More than 50 percent of the cycle time is now usod for face-timbering work.

Jul 1, 1951

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of "lost" air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974