Search Documents

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By Oliver Bowles

"The manufacture of asbestos paper began commercially about 40 years age but its principal development has taken place during the past twenty-five years. The asbestos used by the ancients, termed amiantus by Pliny was used for winding sheets, tablecloths and other fabrics. It was probably chrysotile fiber and was a woven and not a felted product, and there¬fore is not to be confused with asbestos paper. There are, however, some early references to paper manufacture that are of interest. Pontoppidian, Bishop of Bergen, in his Natural History of Norway, published in 1750, refers to paper made from asbestos found in the parish of Waldens. He states that this paper did not burn when thrown in the fire, but the writing on it totally disappeared. This indicates that the primary ob¬ject was to obtain an indestructible writing paper. About 100 years later, further efforts were made with the same object in view. In 1853, a patent was issued for a process of making paper from a mixture of asbestos and alum. Many experiments were made to manufacture suitable asbestos printing paper. Some such papers contained only about one-third asbestos, the remainder being of combustible material. Such papers would burn, but would leave a white residue which retained its shape and preserved the written characters. On account of the difficulty of obtaining a smooth and even surface, and the tendency for the material to absorb ink like blotting paper, asbestos paper is not well adapted for writing or printing purposes. Other early uses of asbestos paper were for ornamental wall-paper and carpet linings. None of the uses mentioned above have developed to anything of importance in a practical way, but the manufacture of asbestos paper has become a very important industry, and it has found extensive uses in ways that were never dreamed of by the early investigators.It is recorded that the first sheet of asbestos paper made in America was manufactured in 1876 by John Roberts & Son Company, in a mill near Waltham, Mass. The material first used was a long-fibered amphibole asbestos from Italy. About three years later, Canadian fiber was introduced and proved to be very satisfactory. The shorter grades of fiber which would otherwise be wasted were used for the manufacture of paper and board. For several years, the product of this mill was sold through Rice Kendall of Boston, Mass. From 1881 to 1900, the H. W. Johns Company, of New York, took the entire product which was 30C to 700 tons per year. The latter company built their own asbestos paper mill at Brooklyn in 1900. Keasbey & Mattison Company, of Ambler, Pennsylvania, began to manufacture in 1897. Other early manufacturers were: the Asbestos Paper Company, at Baldwinsville, Mass„ and Mr. B. S. Binney, at Shirley, Mass. The number of manufacturers gradually increased until at present asbestos paper is manufactured by the following ten companies:"

Nov 1, 1919

By John B. Bennett

This Bureau of Mines report presents a method of standardizing forecasts of mineral consumption that attempts to resolve the problems caused by the use of different data bases, different definitions of minerals consumption, and different base years for making projections. Using this method, forecasts of U.S. and world mineral consumption, in the year 2000, for nine commodities (aluminum, chromium, cobalt, copper, manganese, nickel, tin, tungsten, and zinc) are standardized and compared. Also selected forecasts or associated growth rates are used to generate implied values of consumption for 1980-83, which are then compared to actual values of consumption for 1980-83. The economic growth predictions underlying the forecasts are examined, and some general conclusions are drawn. A description of each methodology used to generate these forecasts is given in an appendix.

Jan 1, 1986

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Wesley A. Grosh

The Toncrae-Howard copper deposits in Floyd County, Va., were first mined about 1800. The property has been operated or under development at various times since then for iron, copper or sulfur, although the total production has been small. The deposit consists of a vein or zone of sulfide mineralization in schist composed mainly of pyrrhotite with minor copper values in the primary zone and some rich areas of copper mineralization in the altered zone. The Bureau of Mines, in an attempt to develop minable copper ore during the war, opened part of the mine for examination and sampling, deepened the shaft and other underground work, and drilled 29 holes totaling 2,187 feet.

Jan 1, 1948

By T. J. Ballard

Corundum is a natural alumina (A120 ) and is next to the diamond in hardness . Except for the gem varieties , it is used principally as an abrasive , chiefly in grinding , dressing , and polishing metals and optical glass . Natural corundum is preferred to artificial abrasives for certain specialized jobs . Most of the corundum ( excluding emery ) mined in the United States came from the Corundum Hill mine in North Carolina and the Laurel Creek mine in Georgia . The Corundum Hill mine provided over half of the domestic production of corundum prior to 1900. Since 1900 , the importation of foreign corundum and the manufacture of artificial abrasives caused the decline of corundum mining in the United States .

Mar 1, 1947

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923

By L. J. Kane

Chemical processes using coal often require economical removal of dust from high-temperature gases. Laboratory-scale investigations by the Federal Bureau of Mines have shown that an aluminum silicate fiber is suitable for filtering dust from gases at 1,800° F. The effects of the bulk density of the filter, rate of gas-flow, concentration of dust in the filter, fiber diameter, depth of filter, and concentration of dust in the feed gas on removal efficiency, pressure drop, and capacity of the filter to hold dust were studied. The laboratory filters were difficult to construct because the fibers were longer than the tube diameter. This caused irregular distribution of fiber that permitted dust-laden gases to leak through channels developed in the filter. Leaks also formed between the filter and the tube wall, but this was minimized by improved filter design. However, edge leaks and leaks through channels in the filter probably would be insignificant in properly constructed filters of industrial size. As the concentration of dust in the filter increased, the efficiency of the low-density filters decreased, contrary to expectations, probably because a higher percentage of the dust passed through channels that developed in the filter. The efficiency of high-density filters, however, increased with the concentration of dust in the filter. Results indicate that loosely packed filters would have a longer life than tightly packed filters at the expense of efficiency. As regeneration or replacement of stationary filters is difficult and expensive, loose filters would be best for filtering gases containing much dust. Gases containing little dust may be cleaned with tightly packed filters to obtain higher efficiency. For either type of filter, precleaning with cyclone separators or other means is advisable.

Jan 1, 1960

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By Wilbur I. Duvall

Surface vibrations of ground, rock, and structures resulting from blasting or other sources are often measured with portable seismographs. These instruments are usually supported by a three-point mount or tripod which is simply placed on a horizontal surface on which vibration levels are to be measured. The rigid-body motion of a tripod-supported seismograph is considered from the point of view that there should be no slippage of the feet with respect to the surface and none of the feet should leave the surface as a result of imparted motion. From these studies the following design criteria are deduced which assure that the seismograph will respond accurately to vibration levels as large as 1/2 g.:3/ First, the coefficient of friction between the feet and the surface on which the instrument rests should be as large as possible, preferably approaching unity; second, the center of gravity of the instrument should be vertically above the centroid of the three-point mount; and third, the vertical distance between the center of gravity of the instrument and the centroid of the three points of contact with the surface should be less than the perpendicular distance between the centroid point and anyone of the three sides of the triangle formed by the three points of contact. Portable seismographs that do not satisfy these conditions should be clamped to the surface if vibration levels above 0.1 g. are to be recorded.

Jan 1, 1961

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By C. E. Arthur

The Bureau of Mines has investigated the problem of radioactive contamination using nuclear explosives to fracture petroleum reservoirs in an attempt to stimulate production. It was concluded that some contamination of petroleum products will almost certainly occur. However) the degree of contamination cannot be predicted except by a full-scale experiment) since simulating the problem in the laboratory is economically impossible because of the extremely high temperatures and pressures that must be reached in extremely short time intervals if a reasonable analog is to result.

Jan 1, 1965

By W. P. Yant

Publication of lists of the devices for giving respiratory protection which have been approved by the U. S. Bureau of Mines is made periodically for the purpose of aiding consumers in procuring equipment .374/ The last published list , approved to March 15 , 1935 , appeared as Information Circular 6845 with the same title as this article . The schedules of requirements and tests which the devices must meet in order to obtain approval are published 2/6/1/8/ by the Bureau of tests the devices must Mines and are available to the public . It is pertinent to mention that the preparation of a schedule of requirements for fresh-air supply devices of the types commonly known as positive -pressure respirators , airline respirators , sand- blast helmets , and hoods , has been practically completed and will soon be ready for release to the public .

Oct 1, 1936

By R. C. Hickman

"INTRODUCTION .As part of its spot drilling program, the Bureau of Mines core-drilled seven holes on the Alexander and Barber properties in Spartanburg County, S. C.Extensive surface float and outcrops of sillimanite schist on these properties appeared to justify drilling, which did not prove satisfactory, however, owing to the spotty occurrence of the schist bodies and the poor core recovery in the decomposed schist.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.This project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Alexander and. Barber properties are in the southern part of Spartanburg County, S. C. The Alexander property is about 5 miles cast of Woodruff. It is reached from Woodruff by driving east 5 miles on a macadam road to the intersection with an unsurfaced road near Unity Church. The farm house on the property is 0.4 mile north on this road. The sillimanite outcrop is in a field approximately 1,200 feet east of the farm house. The Barber property is about 2 miles north along the unsurfaced road that passes the Alexander property."

Sep 1, 1947

By H. B. Brunot, L. C. IlsLey

The design , construction, inspection , and test for permissibility of a storage- battery locomotive outfit in accordance with the requirements of Schedule 15* represents a large amount of work, first on the part of the locomotive manufacturer and secondly on the part of the Bureau of Mines . Detailed information of the first investigation under the schedule is presented here . This investigation covers the inspection and test of a storage- battery locomotive manufactured by the Geo . D. Whitcomb Co. , Rochelle , Ill . , to which Approval No. 1500 was assigned ,

Feb 1, 1923

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988