Search Documents

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By Parviz F. Rad

The increased use of tunnel boring machines (TBM) has stimulated laboratory research to optimize the cutting parameters of these machines with the objective of increasing machine efficiency and penetration rate. Laboratory-scale rock cutting experiments have succeeded in identifying many of the important parameters involved in rock-cutter interaction. Although scaling factors may be required to apply the results directly, the concepts developed can be used qualitatively as design guidelines for boring machines. The Bureau of Mines Twin Cities Mining Research Center has recently developed a large-scale rock cutting device (RCD) that will simulate many of the operating parameters of the tunnel boring machines in the laboratory under a controlled environment. The results of the experiments with this device will be directly applicable to the design of TBM's.

Jan 1, 1973

By F. S. Crawford

The average visitor to a large electric-shovel operation may wonder how electric power can be treated as carelessly as apparently it is in open-pit mining, and how the mining company can string it carelessly along the ground in great, black, hoselike cables, whereas the power company, which has learned to respect his deadly agency, keeps power lines far out of reach. This is explained by the fact that this particular kind of application of power to moving machinery requires the use of trailing cable instead of the more permanent type of construction that permits a moving contact, such as a trolley. The cables are designed to insulate fully the enclosed power lines against damage and loss of current; and employees are taught to handle them carefully, although engineers are not satisfied that the trailing cable is foolproof and are seeking constantly to improve methods and equipment to insure greater safety. In some sections they rely mainly on the construction of the cable and perfection of equipment, while in others additional precautions are taken, such as handling the cable with rubber gloves, slings, tongs, or loops. In some sections no temporary repairs are made to cables, while in others such repairs are made and later are vulcanized in the shop. At some operations the cycle of shovel duties is arranged so that cables are very seldom exposed to flying rock fragments while at others this exposure appears to be unavoidable. Methods of fastening the cable to the shovel frame and transporting the loose cable vary. Inspection and care of the cable are important in insuring its safety and durability. A limited amount of information was obtained by field engineers of the United States Bureau of lines from operators in various parts of the United States, as methods of handling electric-shovel operations differ with the districts; practices followed and equipment used in these districts are described in this circular.

Jan 1, 1936

By Edward F. Divers

Tills U.S. Bureau of Mines report briefly evaluates the advantages and disadvantages of basic dust control techniques presently used by U.S. coal preparation and mineral processing plants. These include ventilation, baghouse-type collectors, wet scrubbers, electrostatic precipitators, source control, sprays, good housekeeping, and personal protection devices. Two specific problems in these types of operations are also considered: dust collector system duct clogging, and control room dust control. Information provided in this report results from dust control research projects conducted by the Bureau at various coal preparation and mineral processing plants over the past decade to reduce workers' dust exposure. These studies indicate that plant ventilation systems normally provide the most cost effective method for dust control. Baghouses and scrubbers were also effective in specific applications, and examples of each are given. In extreme dust conditions, personal protection devices, such as respirators or the dust helmet, can also be highly cost effective.

Jan 1, 1990

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

By Lloyd A. Morley, Alan M. Christman

PART A. ELECTRICAL EQUIPMENT – GENERAL Paragraph 1. Electrical Equipment; Examination. All electric equipment shall be examined, tested, and properly main¬tained by a qualified person to assure safe operating conditions. The examinations and tests shall be performed at intervals not exceeding six (6) months unless otherwise specified in Parts A, B, C, D, and E. When a potentially dangerous condition is found on electric equipment, such equipment shall be removed from service until such condition is corrected. A record of such examinations shall be kept and made available to an authorized representative of the Secretary and to the authorized repre¬sentative of the miners in such mine. Each item of major equipment, in¬cluding substations, switchgear, load centers, and so forth except powered hand tools, shall be recorded separately. The record of such examination shall include all dangerous conditions found, corrective action taken, and name of examiner, and shall be signed by the person responsible for main¬taining the equipment in safe operating condition, who shall also be a qualified person. Paragraph 2. Electrical Work; Qualified Personnel. No electrical work shall be performed on electrical distribution circuits or equipment, except by a qualified person or by a person trained to perform electrical work and to maintain electrical equipment under the direct supervision of a qualified person. Disconnecting devices shall be locked out and prominently tagged by the persons who perform such work, except that in cases where locking out is not possible, such devices shall be opened and prominently tagged by such persons. Locks and tags shall be removed only by the persons who installed them or, if such persons are

Jan 1, 1976

By F. J. Palumbo

Effective recycling or disposal of flue dusts is a continuing problem for copper, brass, and bronze smelters. Over 300,000 short tons (st) of dust is generated annually by U.S. secondary copper, brass, and bronze smelters. The Bureau of Mines has developed an alkaline leach method for recovering metal values from copper converter flue dust containing zinc, tin, lead, and copper. The dust was leached with a hot solution of ammonium chloride and ammonium hydroxide to solubilize ZnO. All of the tin (as Sn02) and the metallic copper, lead, and zinc, as well as possible insoluble compounds of each, report to the residue. Dissolved copper and lead salts are removed from the leachate by cementation with granular zinc. Zinc oxide is precipitated by diluting the leachate with water. The tin-rich (9.8 pct) residue has a ready market. The cement product is recyclable to the smelting operation. The ZnO is at least 97 pct pure and has potential marketability.

Jan 1, 1985

By R. E. Meaker

Electrical conductivities and densities of molten fluoride systems were measured as functions of the melt temperature and composition. For any given mixture, the two properties change linearly with temperature. Three alkali metal fluorides were selected as solvents for melts of the type LiF-, NaF-, and KF-MFx, where M is a metal selected from the alkali metal or alkaline earth groups, or from the lanthanide or actinide series of elements, and x = 1-4. Heats of activation for conductance were calculated from the experimental data and varied from 2.3 to 9.2 kcal/mole at 1,000° C. Some relation between position in the phase diagram and the conductivity changes was suggested.

Jan 1, 1971

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

By C. W. Dwiggins

This report describes the development, theory, and application of techniques and instruments for quantitatively determining nickel, vanadium, and iron in oils, using direct, X-ray emission spectrographic methods (5, 6).3 The methods developed apply to petroleum and other oils as well as some specific fractions of oils. The quantities of nickel, vanadium, and iron in various petroleums are of practical and theoretical interest. Even traces of nickel and vanadium may poison cracking catalysts, and X-ray methods have been used for determining nickel in such catalysts (7). At least parts of the nickel and vanadium occur as metal-porphyrin complexes, a fact which may have considerable bearing on knowledge of the origin of petroleum.

Jan 1, 1962

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010

By Peter Krause

This report provides an overview of the worldwide photographic industry and of the applications of photography. It also covers important technological and market trends, with special emphasis on those factors which may affect the consumption of silver in the future. The text is divided into the following eight sections: 1. Principal manufacturers of silver-based photographic products 2. Major product sectors 3. Structure of the international market for silver-based photographic products 4. Silver-bearing raw materials for the manufacture of photographic products 5. Processing of photographic products: recovery of silver and recycling 6. Methods for estimating the use of silver in photographic products 7. Basic function of silver in photography and alternate image capture and recording systems 8. Brief history of photography Silver- based photographic materials are made for many applications that require different photochemical and physical response characteristics and a wide variety of formats and sizes. All of these products are laminates consisting of a surface-treated support and bonded gelatin layers. Two basic types predominate - films and papers. Films have transparent or translucent plastic supports (mostly cellulose tri-acetate and polyester), while papers have mostly a paper core coated with polyethylene resin layers on both sides (RC type). The front layer contains white titanium dioxide to provide high reflectivity and the back layer a matting agent. However, a few so-called fiber base papers are still supplied. These have a high quality paper base coated with a baryta layer ; i.e. a gelatin layer containing white barium sulfate. The manufacture of photographic film and paper supports requires special procedures and equipment, because of the severe requirements for chemical purity, optical integrity and uniformity (see Table 1 on page 10 for a list of the principal makers of film and paper supports).

Jan 1, 1992

By D. Harrington

"There is continued activity in connection with probable reopening of old-time silver producers, but this is largely offset by other obstacles which make metal mining in Colorado a rather precarious proposition. Discussions at the joint meeting of the Colorado chapter of the American Mining Congress and the Colorado Metal Mining Association in Denver, January 20, 21, and 22, brought out many interesting facts, among them that Colorado, once a producer of high-grade ores, and with freight rates, smelting charges, etc. to accommodate high-grade ores, is now compelled to depend almost wholly upon low-grade complex ores or abandon mining, In the face of this, the railroads threaten to advance freight charges, and smelters , because of decreasing tonnage, high labor, etc., must either advance smelting charges or close (the Globe Smelter et Denver recently closed, and it is said that the Salida Smelter will close in February). A serious menace is the possibility of increase of rates by companies supplying electrical power, and the threat of the agricultural interests, now in the saddle in Colorado, to alter the laws so as to greatly increase the burden of taxation to be borne by the mines.In order to stimulate interest in Colorado metal mining, the Colorado Metal Mining Association and Colorado chapter of the American Mining Congress have planned to have an elaborately staged exhibit in the Denver Auditorium during the latter part of the coming summer, This exhibit will reproduce an old time mining camp,including mining structures such as mills, headframes, etc., as well as the camp saloons, dance and gambling halls, etc., together with mineral exhibits from many of the old time mines, no abandoned, but possibly to be reopened. due to increased price of silver, Inasmuch as the Bureau of Mines plans a National First-Aid meet at Denver in August or September, and the Rocky Mountain Mining Institute will also hold its summer meeting in Denver, it seems advisable to hold the three meetings simultaneously and it is proposed to have this done.Labor supply is fairly abundant and apparently not inclined to be dissatisfied; few, if any, strikes or other labor disturbances being found. In some mining regions advances in wages were posted January 1 and no wage reductions are noted.The Rocky Mountain Coal Mining Institute held its meeting at Denver, January 20, 21, and 22, and much attention was devoted to methods of bringing down coal without use of explosives chiefly by undercutting and subsequent use of hydraulic processes of forcing down the coal. Some attention was given the question of labor and it was suggested that the time is at hand when labor unions should be made responsible bodies by incorporation or otherwise. It was agreed to hold the summer meeting in Denver simul-taneously with the holding of the National First-Aid. and Mine Rescue Meet.In general, coal production in Colorado is proceeding satisfactorily with occasional interruption by local strikes, and tonnage is up to that being produced before the strike, but not nearly up to the record of 1918. In general, the labor supply is plentiful, but demand for coal is by no means great and unless some cold weather intervenes, it is probable that the lignite mines will have to go to a three or four day a week basis. There have been no recent disasters, but the Pictou mine of the Colorado Fuel and Iron Company encountered a heavy supply of water, and had to be abandoned until such time as arrangements can be made to pump or bale the water out."

Jan 1, 1920

By H. C. Brunaugh, James Westfield, R. W. Whittaker

"INTRODUCTION The purpose of this circular is to describe the sealing off of a mine fire and subsequent use of carbon dioxide gas to extinguish it.A fire of electrical origin occurred in the Valier mine of the Valier Coal Co., Valier, Franklin County, I11., on March 29, 1949, at about 1:35 p.m. It was discovered about 3:35 p.m. in 5 south west intake airway inby 1 and 2 west panels. The No. 5 southwest airway had caved, and the fire was in the top coal beneath a large fall of rock. All men, except officials, were ordered from the mine. The mine officials decided to seal the fire, and four temporary seals were erected, which isolated approximately 200 feet of 5 south west entry. The seals were completed on March 30 at 2:45 a.m., but on March 31, at 3;40 a.m,, two of them were blown out by an explosion of gas that was produced by the fire. The two seals were rebuilt, the work being completed on March 31 at 12:00 noon, but they were blown out by another gas explosion at 12:10 a.m. on April 1. It was then decided to extinguish the fire with water if possible.To accomplish this, concrete-block dams were constructed. On April 1, about 4:25 a.m., when the dams were about half completed, water was introduced into the fire area through a 2-inch pipe.On April 4, J. G, Crawford, general manager of the Valier Coal Co., notified James Westfield, chief of the Vincennes (Ind.) Branch, U. S. Bureau of Mines, by telephone of the fire in Valier mine and requested assistance to combat it. Westfield, accompanied by F. J. Smith and H. C. Brumbaugh, Federal coal-mine inspectors, went underground and inspected the seals and dams. Later, during a conference with company officials, it was decided that the concrete-block dams were not strong enough to withstand the hydrostatic pressure that would be produced by flooding the fire area. It was then decided to use carbon dioxide gas to extinguish the fire. Four seals were completed, and 5 tons of carbon dioxide gas was introduced into the fire area, which extinguished the fire."

Apr 1, 1950

By A. S. Peck

This report presents the results of a cooperative study between the Bureau of Mines and the University of Utah to define the mechanism involved in the adsorption of oleic acid and sodium oleate on fluorite, calcite, and barite, using an infrared spectrophotometer for identifying and measuring the adsorbed reagents and reaction products. Fluorite, calcite, and barite react with oleic acid and sodium oleate in a water system, forming chemisorbed and solution products. The chemisorbed species is a surface mineral cation-collector anion salt, Chemical analysis of solution resulting from the adsorption reaction indicates that the adsorption process causes displacement of mineral anions, namely, fluoride, carbon ate, and sulfate from the surface of these minerals.

Jan 1, 1963

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981