Search Documents

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990

By P. Kovalchik

The Bureau of Labor Statistics (BLS) classifies hearing loss as a separate illness category. Hearing loss accounted for 11% of all illnesses in 2005 (U.S. Department of Labor Bureau of Labor Statistics, 2006a). According to occupational data for coal mining provided by the Mine Safety and Health Administration (MSHA) from 2000 to 2005, operators that exceeded 100% noise dosage were from only seven types of machines: auger miners, bulldozers, continuous mining machines, front end loaders, roof bolters, shuttle cars (electric) and trucks (Title 30 CFR Part 62, 2000-2005). Roof bolting machine operators rank second among all underground machine operators that exceed 100% noise dose. There are approximately 600 underground coal mines with 3,930 roof bolting machine operators (U.S. Department of Labor, Mine Safety and Health Administration, 2005; U.S. Department of Labor Bureau of Labor Statistics,

Jan 1, 2008

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By W. G. Bradley

THIS PAPER describing the quarrying, mining, and crushing of gypsum at the Blue Diamond mine, 11 miles from Arden, Nev., on the Union Pacific Railway, is one of a series on gypsum mining being prepared for and published by the Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total production costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

[ ]

Jan 1, 1997

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By J. Burlin Johnson

This report describes an investigation of the relationship between crater dimensions formed in laboratory blasting experiments and the mechanical properties of the material cratered. Scaled field data have been included when available. The results show that tensile strength and possibly other mechanical properties may be useful in predicting maximum crater dimensions.

Jan 1, 1963

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

Lower the respirable dust expo-sure of longwall mine workers by reducing the amount of air-borne respirable dust generated during coal extraction. Approach Increase the moisture content of the coal seam through water infusion before the coal is mined. How Water Infusion Works Increasing the moisture content in coal tends to prevent respirable dust from becoming air-borne during mining and transport. The moisture content of the coal seam can be increased by infusing water into the seam. Water under pressure is forced into the cracks (cleats) of the coal seam through sealed bore-holes. The effectiveness of water infusion is a function of the amount of water the coal seam accepts (its infusibility), which depends on the cleat density (cleat spacing) and cleat size (crack diameter). Thus the effect of water infusion on dust control depends mainly on coal seam characteristics. Water infusion techniques are generally used to restrict the flow of methane gas to the working face; however, the technique provides an alternative dust control method in mines with severe dust problems which limit production.

Jan 1, 1987

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By E. E. Maust

The literature on the activation of sphalerite for flotation by short¬chain xanthates leaves unanswered the question of whether a compact surface film of activator sulfide is necessary or merely sufficient for high flotation recoveries. Studies by Guarnaschelli and Plaksin indicate that xanthate adsorption and flotation of sphalerite are increased with increasing hole/ electron ratio. These results, and the known acceptorlike behavior of many heavy-metal impurities in zinc sulfide, suggest that activation may result from a traditional semiconductor doping effect at the surface. Using the theory of chemisorption states on ionic crystals as developed by Levine and Mark, the Bureau of Mines has carried out A calculation to estimate the surface-state energies of various metals when they are substituted at zinc sites on (110) sphalerite surfaces. Based on a simple Madelung-Born treatment of ionic solids, the calculation indicates that many of the metals known to activate sphalerite for subsequent flotation have lower surface-state energies than nonactivators. The results of these calculations are discussed from the standpoint of consistency with the proposed activation mechanism and observed flotation results. The satisfactory agreement obtained is taken to be support for the proposed mechanism, and further elaboration of a surface-doping model is attempted.

Jan 1, 1976

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By K. A. Fowler, L. W. Higley

The effect of uranium on the transformation kinetics and the hardenability of a low- alloy steel was evaluated . Isothermal transformation curves were developed from metallographic studies , and hardenability was determined by standard Jominy end- quench tests . For the steels investigated , the addition of 0.15 weight- percent uranium was found to produce a significant shift in the isothermal transformation curve and caused a related increase in hardenability . These effects diminished rapidly when the uranium content was increased above 0.2 weight - percent .

Jan 1, 1964