Search Documents

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By C. G. Kirkland

An apparatus for determining trace impurities in Grade-A helium by mass spectrometer methods was designed and built by the Federal Bureau of Mines. Grade-A is the designation for helium commercially produced by the Bureau. Its nominal purity is 99.995 percent. The device, following a suggestion by Deaton, concentrates the impurities in the helium by freezing them out in a coil-and-trap assembly cooled by liquid helium. A known volume of helium is passed through the trap, the concentration ratio determined, and samples of the concentrated impurities are analyzed by mass spectrometer methods. The apparatus has been in service for approximately 20 months and has satisfactorily met all requirements. Over 200 analyses were made of helium contained in conventional cylinders, obtained from the Amarillo, Exell, Otis, and Navajo Helium Plants, during the 6-month period ending March I, 1959. Total impurity concentrations, in parts per million, were as follows: Amarillo, 19.1; Exell, 17.1; Otis, 11.3; and Navajo, 6.6. Neon and nitrogen were the major impurities. Complete data are shown in table 4 in the body of this report.

Jan 1, 1960

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By W. P. Diamond, John C. LaScola, D. M. Hyman

In 1972, the Bureau of Mines developed a direct-method test for measuring the gas content of virgin coal core samples for coal mine health and safety considerations. Since that time, approximately 1,500 coal samples from more than 250 coalbeds in 17 States have been collected for gas content determination. The gas content data, when combined with geologic and engineering studies, can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if methane drainage in advance of mining should be considered. The data are also critical in delineating coalbed methane resources and in utilization feasibility studies. This report makes the Bureau's extensive data base of gas content data more readily available to the coal and gas industries. The data are presented in tabular form, alphabetically by coalbed name and by State. The components of the total gas content (lost, desorbed, and residual gas) are given, Location (State and county), sample depth, coalbed or formation name, and coal rank are included for geographic and geologic identification.

Jan 1, 1986

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By A. J. Barry

Two methods of testing anchorages of headed expansion-type mine roof bolts were investigated by the Federal Bureau of Mines to determine whether they are acceptable for general use. In both methods a load was applied to a tightened bolt with a hydraulic jack. A total of 80 tests, 40 using each method, was conducted in 4 test areas in 3 commercial coal mines. Electric resistance strain gages were used in all tests to indicate true bolt load as the bolt was tightened and when an additional load was applied with the hydraulic jack. The results indicate that: 1. The relationship between the true bolt load and the jack load will vary according to the test method until the two loads become equal. The bolt load-jack load relationship below this point can be determined only with strain gages. 2. The point at which the two loads become equal can be estimated by noting the load when the hardened washer becomes loose in one method, and when the bearing plate becomes loose from the roof in the other. It also can be approximated for either method of testing by noting the load when the first abrupt change in the slope of the jack load-bolt displacement curve occurs. 3. The anchorage characteristics of the test bolt can be determined from the data obtained from either method by examining the slope of the jack load-bolt displacement curve above the point at which the true bolt load is equal to the jack load.

Jan 1, 1960

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By T. A. Johnson

Recovering from low demand in 1975, raw mineral production in the United States maintained a steady climb in value and quantity throughout 1976, keeping pace with the gross national product (GNP), which increased 11.5% compared with that of 1975. The minerals industry, in the past, has met ever-increasing demand while keeping production costs to a minimum. To maintain this capability, technological research and development of more efficient processing methods must continue. The role of Government and its increasing involvement in minerals industry actions received unfavorable comment from various segments of the industry in 1976. Government pricing controls were of concern to most industrial firms marketing like products. Public land withdrawals in large blocks were of concern to the mineral industry.

Jan 1, 1978

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

By W. W. Adams

luring the past two years the Bureau of ?,lines has been receiving from 100 to 150 coal mines in various States a report of each accident causing death, permanent total disability, permanent partial disability, or temporary disability lasting beyond the remainder of the day or shift on which the accident occurred. For each 100 accidents in these groups, there are perhaps from 35 to 45 accidents that do not disable the employee beyond the remainder of the day, and of these fraction-of-a-day accidents the Bureau has compiled no statistics. Information revealed by the reports is to the effect that falls of roof and coal in bituminous coal mines are responsible for 28 per cent of the temporary injuries to underground workers and 33 per cent of the days lost from all temporary injuries underground; they also indicate that falls caused 59 per cent of the deaths from all causes underground. Figures compiled by R. N. Hosler, of the Pennsylvania. Mine Rating Bureau, and covering accidents in bituminous; minis in that State, chow that 61 per cent of the deaths underground during the years 1917-1921 wore due to falls. Neither of these percentage figures includes deaths in major explosions; figures for all bituminous mines in the United States during the five years 1920-1024, inclusive of deaths in major explosions, show that 52 per cent of the deaths underground and in shafts were due to falls of roof and coal.

Jan 1, 1925

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

By John R. Benham

The Long Swamp RARE II area contains no prospects, claims, or mines. It has a low potential for ore deposits. There are no geothermal, oil, or gas leases in the area. APPRAISAL There are no mining districts in the study area. The nearest is Chewack Mining District, which is 6 mi (9.6 km) north of the area. This district had numerous claims located for tungsten; the principal tungsten ore mineral was wolframite. Wolframite was found here in 1898 by surveyors of the International Boundary Commission. The area was staked in 1908 and developed during 1915 and 1916. Only in 1936 was ore shipped; the 30 ton (27.2 t) shipment proved to be unprofitable for the claimants (Culver, 1945, p. 41).

Jan 1, 1982

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

By J. C. White

A research study was conducted to devise a method for producing phosphoric acid directly from unbeneficiated Florida phosphate matrix. This research was performed as part of the Bureau of Mines, U.S. Department of the Interior, goals of improving minerals and metals recovery from domestic resources and of minimizing the environmental impact associated with mineral recovery operations. This report describes research in which unbeneficiated, dry, south-central Florida phosphate matrix was digested with sulfuric acid in a continuous-circuit, five-tank reactor to yield phosphoric acid and gypsum residue. Feed capacity of the reactor was 100 pounds (45 kg) of dry matrix per 24-hour day. When digestion was carried out at 185° F (85° C), acid filtration rates of up to 420 pounds of P20S per square foot per day were attained. Combined iron and aluminum impurities in the product filter acid were about 60 percent greater than values reported in commercially produced acid derived from concentrate. phosphate recovery was 87 to 90 percent of the phosphate contained in the as-mined matrix.

Jan 1, 1978

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992