Search Documents

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By Jack L. Henry, Davis E. Traut, L. R. Penner

The Bureau of Mines conducted solvent extraction batch tests to evaluate the usefulness of neodecanoic acid ( NDA) for extracting Co 3+ from ammoniacal leach liquors high in ammonium sulfate . This work is an outgrowth of previous Bureau research in which technology was devised for the recovery of cobalt , nickel , and byproduct copper from domestic laterites . The previously devised technology uses an oxidative ammoniacal sulfate leach to treat the laterite , and nickel and copper are then recovered from the leach solution by solvent extraction and electrowinning . This report deals with the subsequent solvent extraction of cobalt from the nickel - copper raffinate solution . The results showed that about 70 pct of the contained Co 3+ can be extracted batchwise at pH 8 using NDA ( a 10 - carbon - chain highly branched carboxylic acid ) . However , NDA had a solubility of approximately 0.6 to 0.8 g / L in aqueous raffinate following extraction , and this high solubility makes it impractical for use with alkaline solutions that are low in cobalt . In addition , the extracted cobalt species ( predominately cobaltic hexammine ) is not amenable to the electrolytic recovery of cobalt metal because of its extreme stability . This fundamental prob-

Jan 1, 1965

By S. J. Schatzel, P. W. Jeran, W. P. Diamond, F. E. McCall, F. Garcia, J. C. LaScola, T. P. Mucho

The National Institute for Occupational Safety and Health, Office for Mine Safety and Health Research, is investigating the geologic and mining factors influencing the migration of longwall gob gas. One goal of these studies is to optimize methane drainage strategies to reduce the volume of gob gas that reaches the underground workplace. As part of this research effort, longwall gob gas flow paths in a mine operating in the Pittsburgh Coalbed, PA, were investigated using SF6 tracer gas. Tracer gas released into the ventilation airflow underground generally stayed in the bleeder system and was vented at the associated bleeder fan shafts. Tracer gas injected into an inactive (intaking) gob gas venthole migrated to the two inby producing ventholes on the study panel, indicating that all three ventholes were in communication. The tracer gas that was injected into the gob generally stayed in the gob and only migrated to the ventilation system in response to the venthole on the study panel closest to the injection hole going off production. Tracer gas flow velocities in the longwall gob reservoir and factors influencing the production performance of gob gas ventholes in the study area are also discussed.

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

Develop geophysical techniques suitable for enhancing miner safety. Specifically, to use geophysical methods to detect hazardous conditions in a rock mass in deep underground mines as well as to assess the mechanical integrity and monitor changes of the rock.

Jan 1, 1997

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

This report deals with the Schmalfeldt gasification plant for making synthesis gas, the Fischer-Tropsch plant, the hydrogenation plant and the catalyst factory, and includes a report on lubricating oil. THE SCHMALFELDT GASIFICATION PLANT The information was obtained on May 9 and 11, 1945, from Dr. Schneeberger (director), Dr. Schneider (director and power plant manager), Herr Dassau (manager of gas plant) and Herr Schultz (manager of Fischer-Tropsch plant). The plant was shut down as the result of very heavy air raid damage to other parts of the works

Jan 1, 1946

By M. G. Zabetakis

The use of liquid hydrogen as a high-energy fuel introduces numerous hazards not ordinarily associated with the use of other more conventional fuels. These hazards are attributable to the unique properties of hydrogen in the liquid and gas states (table 1). Since little work has been conducted on explosion and related hazards of cryogenic fuels, a research program was undertaken to obtain basic data on such dangers for hydrogen and other combustibles under these conditions. These data were used to outline emergency procedures for protecting personnel and equipment when an accidental spillage of liquid hydrogen occurs and to establish a quantity-distance table for the storage of this fuel. The vaporization of liquid hydrogen from a surface is treated as a prob¬lem in heat transfer theory. Two extreme cases are briefly considered: (1) The transfer of heat occurs at constant temperature drop between, the boiling liquid and the hot surface, and (2) the transfer of heat is limited by the rate at which it can flow to the surface from a hot insulating medium. The available data indicate that the former case (1) is applicable when vaporizing from a conducting surface and, initially, when vaporizing from an insulating medium; the latter case (2) is applicable after initial flash vaporization has occurred from the insulating medium. The vaporization rate determines in part the rate at which flammable hydrogen vapor-air mixtures are formed above a spill area. However, the rates at which heat is transferred to the vapor, and air is brought in contact with it also are of importance. Accordingly, the distribution of flammable mixtures above a spill area was determined experimentally. In general, flammable mixtures were found to be both above and within the visible vapor cloud.

Jan 1, 1961

By J. Drew Potts

The U.S. Bureau of Mines identified respirable dust sources and controls on four continuous auger mining sections, two with relatively low dust levels and two with high levels. Factors adversely affecting dust levels included auger equipment design, continuous haulage, and low seam height. Dust controls included ventilation practices and spray systems. Maximizing airflow seemed to reduce dust levels most. Air leakage and shock loss can be reduced by constructing stoppings with brushed-on mortar containing fiberglass and by keeping areas between curtains and ribs free from obstructions and storing equipment not essential for face activities in outby crosscuts. Curtain configuration, setback distance, and installation can also affect dust levels. Use of both blowing and exhausting curtains is the most effective configuration. Setbacks from the face should not exceed 15 ft. Installing brattice curtains at least 5.5 ft from ribs, when entries are 26 ft wide, minimizes velocity head. Installing curtains tightly against the mine roof and floor helps maintain a forward airflow movement in the center of the mine heading; curtain overlap can create a tighter seal. The wet-auger spray system also effectively controls dust, provided the mine is already exercising good ventilation practices.

Jan 1, 1989

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

Dump site injuries occur in all major mineral industries. Working in elevated areas near an edge is a common hazard for operators of off-highway mobile mining equipment. In this Information Circular (IC), serious injuries involving haulage trucks working at dump sites are examined for the period 1988 to 1997. Data were acquired from injury reports gathered by the Mine Safety and Health Administration (MSHA). The IC is organized into three sections. The first presents an overview of the frequency and severity of injuries. The second analyzes injury characteristics using MSHA-defined data fields and author-defined injury classifications. Key findings are discussed in the third section. In summary, 370 serious injuries were identified that involved trucks at dump sites, of which 26 were fatalities. Although haulage truck activities at dump sites resulted in a small proportion of the total number of injuries at surface mines, these injuries were much more likely to result in death or significant amounts of lost time than most other surface mine injuries. These findings support the belief that haulage truck activities at dump sites are worthy of continued study by those interested in improving the health and safety of workers at surface mines.

Jan 3, 2001

By D. F. Reed

As a part of a comprehensive survey of the Adirondack region, the Bureau of Mines, 1944 and 1945, conducted investigation of magnetic deposits at Dennemora, Russia Station, Redford-Clayburg, Standish, and the Ausable river region. Later in 1945, the Federal Geological Survey, started an aeromagnetic survey of the area and completed it in .1946. The Bureau of Mines extended its magnetic surveys in 1946 in the Redford-Clayburg area. In 1947 the Bureau of Mines .diamond-drilled throe holes in the Redford-Clayburg district. Clinton County has one active magnetite mine at Lyon Mountain and inactive mines at Palmer Hill and Arnold Hill, as well as along the Saranac River.

Jan 1, 1949

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968

By Nar S. Dalal, Xianglin Shi, Val Vallyathan

"INTRODOCTIONIn an earlier communication 1 from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates of free radicals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubini et al.2 have also reported the detection by electron spin resonance (ESR) of the formation of SiO. and Si-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum ( -10-10 torr>3 and subsequent exposure to air,3 and to other gases,4 these radicals were identified2 as being formed by the homolytic cleavage of the Si-0-Si bonds and the reactions of the Si• and SiO- radical with atmosphere. Fubini et al.2 also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anca5 bad reported that lipid ·peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radica1 studies on a given quartz dust sample have been reported, except for some earlier work from our laboratory.1·6·7 We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radica1 measurements on a freshly made quartz dust. The dust's free radica1 content was measured using ESR spectroscopy while its cytotoxicity potential was estimated via hemolysis. Hemolysis was employed as the toxicity test because it is a widely used method for estimating the potential of a dust for disrupting the cell membrane. 8 The fibrotic potential was followed by measuring the dust-induced lipid peroxidation, using linoleic acid as a model lipid. As discussed below, the results obtained suggest new clues to the mechanism of the quartzrelated cytotoxicity and fibrogenicity. MATERIALS AND METHODSReagentsCrystalline quartz particles with a size range of 0.2-2.5 mm were obtained from the Generic Respirable Dust Technology Center, Pennsylvania State University, University Park, Pennsylvania. These particles were crushed in air to obtain quartz dust samples with particle sizes smaller than 20 microns. We chose to work with a dust with mixed particle sizes, rather than a specific range, as an effort to simulate the mining atmosphere. An agate mortar-pestle arrangement was used for the crushing and grinding because of the close similarity of the structure of agate to that of quartz. Diethylenetriaminepentaacetic acid (DETAPAC) were purchased from Sigma. All other chemica1s were purchased from Fisher or Aldrich.Hemolysls ExperimentsHemolytic activity of silica was measured, following an established procedure,9 as the amount of hemoglobin released from a 2 % suspension of sheep erythrocytes after incubation with 10 mg of silica dust for one hour at 37 °C. The hemoglobin release was estimated via the absorbance at 540 nm using a Gioford spectrophotometer. The procedure was calibrated by substituting the silica dust by a phosphate buffer solution as a negative control (background) and O.S % Triton-X-100 as a positive control (100% hemolysis). The percentage of hemolysis was calculated as follows:"

Jan 1, 1990

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960