Search Documents

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By Webster S. Anderson

The design, development, and testing of hydraulic props to provide a lightweight, high strength, recoverable unit is described. Modifications in design incorporating threaded components resulted in the development of a lightweight hydraulic prop fabricated from aluminum alloy tubing. This new design facilitates interchange and replacement of component parts, and the physical properties of the material are not changed as they are when welding is required. The new prop is 65,000 pounds and has a maximum load capacity of a lower weight-to-load capacity ratio than the hydraulic props now available.

Jan 1, 1967

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By Edward G. Cunney

Track in underground bituminous coal mines was investigated, and technology was taken from other industries in order to obtain information on conditions that impair the safety and efficiency of the track and to develop guidelines and useful information on the construction, inspection and maintenance of mine track. Volume 1 contains information on the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and recommended limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage; descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques, inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it does not repeat the summary or derivations. Volume 3, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for' ready reference by inspectors in the mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.

Jan 1, 1977

By Warren Hastings

This paper describes the methods and costs, in units of labor end materials, of sinking a 7 compartment vertical shaft 1,261 feet through a fractured, water-saturated formation. The shaft, designed for hoisting 2,500 tons a day, is at Friedensville, Lehigh County, Pa., approximately 6 miles south of Allentown and Bethlehem. It was sunk by the E. J. Longyear Co. under contract to the New Jersey Zinc Co. Preparation for shaft sinking W8A begun July 1, 1947, and sinking was completed August 18, 1952. A total of 604,858 man hours was required to sink the shaft.

Jan 1, 1954

By Thomas M. Barczak

This Bureau of Mines report investigates shield mechanics by describing the elastic response and interaction of shield components to applied vertical and horizontal displacements for various canopy and base contact configurations. This research provides information on generalized shield mechanics, which is applicable in describing the behavior of all two-leg shield supports. Utilizing mechanics of materials concepts and known kinematic relationships for two-leg shield supports, free-body diagrams are constructed for each shield component illustrating internal axial, shear, and bending moment responses required to maintain equilibrium for each load case evaluated. Predicted shield (component) responses are verified by controlled displacement of instrumented longwall shields in the Bureau's mine roof simulator (MRS). Conclusions drawn from these analyses include shield structural responses are significantly dependent upon canopy and base contact configurations. Applied displacements also significantly affect shield responses. Horizontal displacement produces different responses than those produced by vertical displacements. The direction of horizontal displacement is also significant in evaluating shield response. Applications of shield mechanics to in situ support monitoring are also discussed. An objective of this research program is to establish unique shield responses to identify in situ load conditions.

Jan 1, 1989

By Edward E. Johnson

The U.S. economy boomed in 1965, completing its fifth consecutive year of expansion. Although the advance was somewhat irregular, previous records for production, sales, employment, and income were topped. During the first few months of 1965, as the economy recovered from the depressing effects of the automobile strikes of late 1964, increases were unusually large. The gains moderated in early spring, but were stimulated at midyear by sharply rising capital outlays, excise tax cuts, in? creased Social Security payments, and accelerated Viet-Nam defense expenditures. Gross national product (GNP) in cur-rent dollars rose $49.5 billion or 7.8 percent, to a total of S681.2 billion. In constant dollars (effects of price changes eliminated), GNP increased 5.9 percent, a rate considerably higher than the historical postwar annual average growth of 3.5 per-cent. Demand increased in most final markets and was especially strong for business fixed investment and consumption expenditures. With the exception of construction, most of the increases in GNP were real, since prices increased less than 2 percent.

Jan 1, 1966

By G. D. Jermain

The Bureau of Mines investigated the Gypsum-Camel deposit on Iyoukeen Cove Chichagof Island, Southeastern Alaska, from April 21 to August 26, 1948, as A part of the United States Department of the Interior program for developing an Alaskan construction industry. As gypsum is one of the components necessary for the manufacture of cement and one of the raw materials for plaster and plaster-board products, it is desirable to locate and develop a readily accessible deposit of gypsum in Alaska. In 1928, B. D. Stewart of the Territorial Department of Mines surveyed the gypsum deposits at Iyoukeen Cove, and during the summer of 1946 George M. Flint, Jr., and Edward H. Cobb of the Federal Geological Survey examined and mapped the old workings at Gypsum Creek and the prospect at Iyoukeen Cove. Both the Territorial Department of Mines and the Federal Geological Survey recommended the Gypsum-Camel prospect as warranting a diamond-drilling program by the Bureau of Mines. The Bureau of Mines project consisted of cleaning out and sampling, the old underground workings and diamond drilling from the surface to ascertain the lateral extensions of the deposit.

Jan 1, 1952

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986

Pillar design is the first line of defense against rock falls—the greatest single safety hazard faced by underground coal miners in the United States and abroad. To help advance the state of the art in this fundamental mining science, the National Institute for Occupational Safety and Health organized the Second International Workshop on Coal Pillar Mechanics and Design. The workshop was held in Vail, CO, on June 6,1999, in association with the 37th U.S. Rock Mechanics Symposium. The proceedings include 15 papers from leading ground control specialists in the United States, Canada, Australia, the United Kingdom, and the Republic of South Africa. The papers address the entire range of issues associated with coal pillars and have a decidedly practical flavor. Topics include numerical modeling, empirical design formulas based on case histories, field measurements, and post failure mechanics.

Jan 5, 1999

By H. D. Kline

Manganese ores have been mined in the Batesville district since 1849. Although not continuous over the intervening years, production had totaled approximately 432,000 tons of manganese ore and ferruginous manganese ore to the end of 1953. The ores occur in deposits, essentially low in manganese content, distributed over an east-west belt 24 miles long and 4 to 8 miles wide, the core of which is about 6 miles north of Batesville, Independence County. Although the reserves of high-grade ores in the district are comparatively small, the large deposits of subgrade ores and low-grade manganiferous material comprise potential sources of supply of manganese that may have increasing future importance. The manganese occurs as primary oxide and carbonate minerals in relatively flat-lying limestone and shale formations in which they were originally deposited and as oxides in residual clays resulting from decomposition of the shale and lime-stone. Most of the deposits underlie from a few to over a hundred feet of sedimentary chert, but many occur in the residual clays on exposed slopes of chert-covered hills.

Jan 1, 1956

By Albert L. Toenges, Louis A. Turnbull, Alonzo W. Quinn, J. M. Schopf, Arthur Neale, R. F. Abernethy

"INTRODUCTION The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war materiel; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this critical fuel situation, an investiga¬tion was made of possible sources of fuel nearer to points of consumption in New England. Meta-anthracite, which is a satisfactory fuel for some purposes, had been mined in Massachusetts and Rhode Island many years ago. However, the introduction of freer-burning anthracite and bituminous coal into New England markets resulted in the abandonment of these mines.The coal mined in the vicinity of Portsmouth on Aquidneck Island, Newport County, R. I., had been used successfully for smelting copper ore and for fuel. It is reported that this coal is less graphitic than the material mined at Cranston near Providence, R. I. The coal is meta-anthracite and does not burn freely. However, improved equipment for burning coal has been developed, and if minable reserves of meta-anthracite should be found, methods of burning it probably could be devised.The purpose of this investigation was to determine sources of additional fuel. Since meta-anthracite mined at Portsmouth had been used with some success, an investigation was undertaken to determine the characteristics and continuity of the beds in this area."

Apr 1, 1948

By R. M. Santmyers

"Quartz and silica not only occur in diversified forms in nature but find a multiplicity of uses in industry. The purpose of the present paper is to assemble brief summaries of the many widely differing industries engaged in the production and preparation of these minerals in their principal commercial forms. Due to the scope of the subject it was though advisable to divide the paper into three parts. Part I deals with the subject of quartz and silica in general. It also contains a flow sheet of silica from deposit to consumer (fig. 1). Part II covers the uses and other economic factors of quartz, quartzite, and sandstone, the varieties of silica found in consolidated form. Part III deals with sand and miscellaneous silicas such as tripoli and diatomite. A chart showing the major ramifications of these industries is presented herewith as an introduction to the more detailed discussion that follows.For a more intensive study of many branches of the quartz and silica industries the reader is referred especially to Bulletin 263 of the United States Bureau of Mines, Technology and Uses of Silica and Sand by W. M. Weigel. For annual statistics relative to silica and its products in the United States he is referred to the annual chapters of Mineral Resources of the United States, entitled ""Silica,"" ""Sand and Gravel,"" and ""Abrasives."" With respect to diatomite reference is made to Diatomite, by Paul Hatmaker, recently issued by the U. S. Bureau of Mines as Information Circular 6391. In preparing this paper the author has drawn freely from these sources as well as Marketing of Metals and Minerals, by J. E. Spurr and F. E. Wormser; Non-Metallic Minerals, Occurrence, Preparation and Utilization, by Raymond B. Ladoo; and Abrasives - Part I, Siliceous Abrasives, by V. L. Eardley-Wilmot, Report 573, Mines Brand, Department of Mines, Ottawa, 1927.Acknowledgment is also made to the Foote Mineral Co., which has published in Foote-Prints (vol. 2 of 1929 and vol. 1 of 1930), comprehensive reviews of the uses of crystal quartz in the optical industry and as piezo¬electric crystals.The various forms of silica have attracted attention from the earliest times, and the water-clear crystallized variety was known to the Greeks as""krystallos"" (clear ice), being supposed by them to have been formed from water by the intense cold of the Alps; hence the name ""crystal"" or more commonly ""rock crystal,"" applied to this variety. The name quartz is an old German word of uncertain origin used by G. Agricola in 1529.Silica or silica dioxide (Si02) either free or in combination with other elements constitutes 59.08 per cent of the lithosphere, and quartz alone represents fully 12 per cent` of all rocks. Next to the feldspar group quartz is the most abundant mineral in the earth's crust; and it appears in a greater number of varieties and modes of occurrence than any other mineral. Silica or quartz occurs in crystalline, cryptocrystalline, microcrystalline, and amorphous forms. The most common, however, is the crystalline form, which occurs as three minerals, quartz, tridymite, and crystobalite, and of these three tridymite and crystobalite are quite rare in nature."

Aug 1, 1931

By Eugene V. Cilento, R. Clark Lantz, Kevin A. DiGregorio

"A microscope-based spectrophotometer has been developed to measure superoxide release from single pulmonary alveolar macrophages (PAM) or other phagocytes in culture. Results indicate that PAM respond to stimulation by phorbol myristate acetate (PMA). It appears that some PAM do not release 02 upon stimulation by PMA; however, those that do release 0, show differences in: (I) the total amount of 0, released, (2) the rate of release of 02 and (3) the time delay for release of 02. The significance of measuring 02 release from single cells is two-fold. It allows the simultaneous study of 02 release and electrical potential changes across the membrane of PAM and it allows the study of differences in 02 release among cells. Thus, the function of Normal PAM and the dysfunction of PAM exposed to coal dusts can be more closely studied on single cells.Pulmonary alveolar macrophages (PAM), free cells found in the lungs, protect the lungs by removing inhaled foreign debris and bacteria. The macrophages do this by engulfing and then internalizing the foreign matter (phagocytosis). Stimulation of PAM causes the release of super-oxide radical (02) which has been shown to be the primary metabolite involved in the killing of bacteria by phagocytes (3,8,12). The super-oxide radical is highly reactive and is spontaneously or enzymatically converted to other antibacterial oxidants, including hydrogen peroxide (H202), singlette oxygen ( 02), hydroxyl radical toil'), and hypochlorous acid (HOCl) (2, 3,8,11,12).Exposure of PAM to dusts may lead to dysfunction of this cell-type and to a greater risk of lung damage or infection upon subsequent exposure to toxic dusts. To date, much of the research with this cell-type has used cytotoxicity (cell death) as a measure of dysfunction. Although this is an important end point, PAM dysfunction may occur at doses below those which lead to cell death. In addition, dysfunction has been measured using large numbers of cells. In order to obtain a clear understanding of the mechanisms involved in dysfunction, measurements should be made on single cells. As mentioned earlier, one of the major roles of this cell type is its anti-bacterial actions. Therefore, asessment of release of superoxide radical in single cells is important in determining the functional behavior of PAM before and after exposure to dusts. Since measurements of 02 production have not been made on single cells the purpose of this study is to develop the methodology needed to study release of 02 from single cells.Recent studies have suggested that a relationship exists between the release of 02 and changes in the electrical properties of phagocytes. The change in membrane potential is thought to be the initial step in superoxide production (6,9). Stimulants which cause 02 release also cause changes in the transmembrane potential of phagocytes (9) and in the permeability of the cell membrane to ions (6). For example, stimulants which cause the release of 0, from neutrophils have also been shown to increase the membrane transport of Na+ , K+ and Ca+2 and stimulation of macrophages leads to increases in Na and perhaps Ca permeability with a subsequent change in membrane potential. In some cases, phagocytic activity has been shown to depend upon the extracellular concentrations of these ions (6). Holian and Daniele (7) have shown evidence that the redistribution ofcellular Ca in alveolar macrophages is an initial step leading to 0, release. In order to provide direct evidence that 02- production is related to electrical changes across the plasma membrane of phagocytes, these two phenomena must be analyzed simultaneously on single cells. Ultimately, measurements of 0, release using the methodology developed in this study will be combined with electrophysiological tech¬niques to study both superoxide release and membrane potential changes simultaneiously on single PAM, and to examine the effects of coal and mineral dusts on their physiological fu"

Jan 1, 1988

By Frank J. Cservenyak

Curtailment of bauxite importation by enemy activities during World War II focused attention on the necessity of developing domestic deposits of aluminous materials. Large quantities of aluminum ores such as kaolin, siliceous bauxites, high-iron bauxites, anorthosite, and diaspore clays are available but not readily amenable to Bayer processing because of excessive impurities. The Bayer process, which is the only commercial method in use in the United States for producing metallurgical-grade alumina, requires a high Al2O3 bauxite relatively low in SiO2 and Fe2O3. The Bureau of Mines was charged by Congress to investigate processes for the production of alumina from these low-grade ores. One part of the program was an investigation, in the laboratory and pilot plant, of the recovery of alumina by the lime-soda sinter process. Ores comprising kaolin, diasporic clays, anorthosite, and siliceous bauxites have been investigated and studied in the laboratory and pilot plant, and a series 'of reports covering these investigations has been prepared.

Jan 1, 1948

By H. D. Jacobs

The Bureau of Mines undertook a research program to insure an adequate supply of iron raw materials for future iron and steel making needs. A sample was obtained of oxidized taconite from the western Mesabi Range in Minnesota, and the metallurgical response of the taconite to beneficiation by a process that included selective flocculation-desliming-cationic flotation was evaluated. The sample contained 35.3 pct iron and represented approximately 2 billion tons of crude material. Selective flocculation and flotation were evaluated in a pilot plant with a feed rate of 900 Ib/hr. Concentrates averaging 61.7 pet iron and 5.1 pet silica were obtained, with an accompanying iron recovery of 67.2 pet. About 83 pct of the process water requirements were reclaimed from the slime and froth tailing and then recycled.

Jan 1, 1980

By Northcutt Ely

This volume- summarizes mining and petroleum legislation in 18 European jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identitication of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis; of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added in countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1974