Search Documents

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By V. F. Parry

[Approximately 7-1/2 million tons of subbituminous coals are mined annually in Colorado, Wyoming, and Montana, of which 50 percent probably reaches domestic consumers. The moisture of these subbituminous coals is high, averaging about 25 percent when they are mined. The coals are non-caking end stack to a variable degree when exposed to normal atmospheric conditions. They are good domestic fuels, are considered to be smokeless in most furnaces, and have been used for many years in hand-fired domestic furnaces in which the practice is to employ large lutes for efficient combustion.]

Jan 1, 1941

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By A. F. Colombo

Laboratory-scale tests were conducted by the Bureau of Mines on an argillaceous Michigan copper ore and mill tailing to determine the feasibility of leaching with acidified ferric sulfate solutions. The ore and tailings, containing 1.24 and 0.24 percent copper, respectively, were from the White Pine Copper Co., Ontonagon County, Mich. The investigation showed that ferric sulfate leaching of the ore and tailings followed a predictable pattern. Thus, with 4 hours of leaching, up to 58 percent of the copper in the ore was extracted, but prolonged leaching (2 to 3 weeks) was required to dissolve more than 90 percent of the copper. Similarly, about 50 percent of the copper in the mill tailings sample was dissolved in a few hours, but 8 days or more were required for extractions of over 90 percent.

Jan 1, 1962

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By L. M. Chan, D. H. Carlson, J. B. Johnson

"Abstract — Concentrations of tailpipe pollutants from diesel-powered. underground mine vehicles change over time due to engine wear and the need for maintenance. Since this deterioration in pollutant emissions may adversely affect the air quality in an underground mine, it should be monitored and controlled. This paper presents decision criteria concerning when to service a mine vehicle diesel engine. These criteria, based on mine air and tailpipe concentration measurements, are designed to maintain the tailpipe concentrations within limits that assure satisfactory mine air quality.Application of the deterioration criteria to mine vehicle emissions involves:establishing, for each pollutant, the allowable deterioration factor, anddetermining the deterioration factor, from the mine air and tailpipe diesel pollutant measurements, and the mine air threshold limit values (TLVs).If the deterioration factor is greater than or equal to the allowable deterioration factor the vehicle is removed from service for maintenance.An analysis applying the criteria to measurements made in an underground coal mine is presented. The tailpipe pollutant concentration data were collected using the Emissions Mea-surement Apparatus (EMA) developed by Michigan Techno-logical University. Since the TLV for diesel particulate matter (DPM) has not yet been established assumed mine air DPMTLVs of 15 and 1.0 mg/m3 were used in the analysis. For all of the diesel haulage vehicles included in the analysis. DPM was found to be the critical pollutant (the one most in need of control). For an assumed mine air DPM TLV of 15 mg/m3 none of the diesel haulage vehicles would he removed from service. However reducing the DPM TLV to 1.0 mg/m3 would make it necessary to remove two of the three vehicles tested from service."

Mar 1, 1992

By A. B. Hooker

Gassy mines require daily inspections with methane detectors to test for the presence of methane. Although in many manes it may be sufficient to know that there is no methane present or that its percentage is below a certain amount, it is desirable and often necessary to determine definitely the percentage of methane at the working faces and in the various air currents. The Bureau of Mines recognizes two general types of portable methane detectors, namely; 1. Methane detectors by which the presence of methane may be detected and its approximate percentage estimated.

Jan 1, 1929

By Ronald S. Conti

The Bureau of Mines conducted a comprehensive laboratory study of the thermal ignitability of various carbonaceous dust clouds with particular emphasis on various ranks of coal dust. The tests were conducted using a new 1.2-L furnace. Autoignition temperatures of dust clouds were obtained as a function of coal volatility and particle size. Dust particles and gas samples were collected by a rapid-sampling system in order to study the reactions involved in preignition and postignition processes. The autoignition temperatures measured in the new 1.2-L furnace were significantly lower and therefore more conservative than those measured previously in the Godbert-Greenwald furnace. The combined effects of thermal and electrical ignition of dust clouds were also studied in the 1.2-L furnace using electrical discharges of varying energies at ambient and elevated temperatures. The minimum spark energy necessary to ignite a dust cloud decreased significantly as the temperature of the dust cloud increased.

Jan 1, 1983

By Frank A. Peters

An evaluation is made of a lime-soda sinter process for extracting alumina from clay. In this process, alumina is extracted by sintering clay with soda ash and limestone and then leaching the sinter with a dilute sodium carbonate solution. The sodium aluminate solution formed during leaching is separated from the residue and treated with lime in autoclaves to remove dissolved silica before alumina trihydrate is precipitated with carbon dioxide. The tri-hydrate is then calcined to a-alumina. Two options, dry grinding and wet grinding, are used in the sintering step. The fixed capital costs for plants producing 1,000 tons of alumina per day are $72 million for the dry grinding option and $66 million for the wet grinding option on a Marshall and Stevens chemical equipment index basis of 240.0. Specific geographic locations of plant and raw material sources are not assigned, but, since this process requires large quantities of both lime-stone and clay, the plant site is considered as variable with relation to the clay mine and limestone quarry. A nomograph is given to find operating costs at various delivered costs of clay and limestone. If the plant is located nearer the limestone quarry so that the delivered cost of clay is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $76.47 and $71.61 per ton of alumina for the dry grinding and wet grinding options, respectively. On the other hand, if the plant is located nearer the clay mine so that the delivered cost of clay is $1 per ton and the delivered cost of limestone is $2 per ton, the operating costs are $80.15 for dry grinding and $75.34 for wet grinding.

Jan 1, 1967

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By O. C. Blade

Sales of diesel fuel in the United States exceeded 150,000,000 barrels during 1953 and 140,000,000 barrels during 1952. Following are some figures on the distribution of this fuel computed from data issued by the Bureau of Mines. 2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,170,000 barrels during the first six months of 1954, 3/ a corresponding figure for 1953 was 86,284,000 barrels.

Jan 1, 1954

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, M. J. Keane

"Therma1 and chemical treatment of respirable size silica dusts samples is shown to induce marked changes in their hemolytic activity. The cytotoxicity of crystalline a-quartz (Min-U-Sil), and fumed silica (Cab-0- Sil) particles, as measured by a hemolytic activity protocol, is decreased by calcination and can be related to the dehydroxylation of the surface. The hemolytic activity of P-cristobalite particles of respirable dust si7.e was also determined and found to be lower than that of a-quartz. The change in the surface structure resulting from thermal treatment is detectable by photo-acoustic infrared spectroscopy and zeta-potential measurements. The absorption band in the 3200-4000 cm-1 frequency region of both Cab-0-Sil and MinU- Sil disappears upon heat treatment while a sharp band, identified with single silanol groups, at 3750 cm-1 increases in intensity. The zeta potential-pH profile, in the pH range of 4.0-7 .0, of the calcined, siloxane surfaced particles is more negative than that of material with a silanol surface.The cytotoxicity of the crystalline and fumed silica dusts was also found to be strongly dependent on particle size. Fumed silica of large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. INTRODOCTIONThe toxicity of silica and other mineral particles, as manifested by their role in inducing pneumoconiosis, fibrosis, silicosis and other pulmonary disorders is largely traceable to the characteristics of particle surfaces and to particle morphology. The great wealth of data on the physical and chemical properties of silica is still insufficient for a comprehensive understanding of the specific parameters to be associated with fibrogenic activity and, correspondingly, with the optimum means for characterizing and quantifying the toxicity of dusts, and the design of possible preventive or therapeutic methods.The great diversity of parameters that have been proposed and tested for correlation with cytotoxicity suggest that more than one mechanism may be involved in the fibrotic activity of silica particles. The crystalline structure of the material (more active tridymite versus less active crisobalite and passive stishovite), freshly formed surfaces and free radicals associated therewith, silicic acid adsorbed onto silica surfaces, the concentration of hydroxyl groups at silica surfaces, particle size and morphology, among other properties, have been investigated and found to conelate in tests of cytotoxicity."

Jan 1, 1990

By Paul C. Turner

The U.S. Bureau of Mines, through an Interagency Agreement with the U.S. Army Tank-Automotive Command (TACOM), has successfully developed a steel expendable pattern casting process (EPC) for the manufacture of armorplate. The new armor is lighter and more ballistically effective than conventional rolled homogeneous armor (RHA), and costs less. An applique armor spinoff from the program was field-tested during the Gulf War. The applique armor withstood direct impacts from enemy munitions without failure.

Jan 1, 2010

By R. M. Gammell, S. H. Lorain

The Anderson prospect is one of a number of properties investigated by the Bureau of Mines during the course of preliminary studies of the lead-zinc districts of northern Stevens County, Washington. examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. This examination was supplemented in late 1944 and the spring of 1945 by pre- The property was first liminary angle-dozer trenching and core-drilling. A second examination of the property was made by the junior author in November 1945. The data obtained in the course of these studies is presented in the following report.

Mar 1, 1947

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By Lowell Stroud

Since 1929, the Helium Activity of the Bureau of Mines has operated a helium-extraction plant at Amarillo, Tex. The natural gas that supplies this plant is obtained from the Cliffside geologic structure 12 miles to the northwest and over the years, has become known simply as "Cliffside gas," There is need for published data on the low-temperature phase equilibria of helium-bearing natural gases. To date, little information has been published on the equilibrium phase compositions, solution of helium in condensed natural gas, condensation characteristics, or equilibrium vaporization coefficients for methane, nitrogen, and helium in helium-containing systems. A windowed phase equilibrium apparatus (8)6 was used to obtain 105 equilibrium samples, representing 35 experimental conditions of condensed Cliffside gas at pressures of 100, 200, 300, 400, and 500 p.s.i.a. and temperatures from 0° to -270° F. Data on equilibrium vapor-liquid composition for Cliffside gas are presented in both tabular and graphic form and are discussed in detail to show their relationship to certain criteria that must be met to effect an efficient separation of helium from natural gas by means of low-temperature processes. Facts about condensation characteristics and solution of helium in the liquid phases are included, The important relationship of these two factors in decreasing the percentage of total helium lost by solution in the liquid phase is discussed.

Jan 1, 1961