Search Documents

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010

By R. E. Kennedy

The presence of combustible gases and vapors in air can constitute n extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and. allied industries, the U. S. Bureau of Mines has investigated the explosive properties of a number of gaseous and liquid compounds; the results of these investigations have been published in various government papers and journal articles. The increased use of liquefied, petroleum gases has intensified interest in the effect of high pressures on the explosibility of propane-air mixtures. The limits of flammability of natural gas-air mixtures have been determined at pressures ranging from 50 min. Hg to 3,000 p.s.i. As it is known that a combustible. gas or vapor cannot burn or explode when the oxygen content of the atmosphere is less than a certain value, critical values were determined for the oxygen content of atmospheres to which nitrogen had been added as a diluent. In this connection limits of flammability were determined for ethane in atmospheres containing added. nitrogen or carbon dioxide at pressures up to 900 p.s.i.g.

Jan 1, 1951

By W. L. Crentz

San Juan County, which occupies the extreme northwest corner of New Mexico, contains large reserves of coal in the Fruitland formation and in the Menefee formation of the Mesaverde group. The coals have bright luster, are brittle, and break easily in handling. All mines sampled are in the La Plata-Fruitland and Rio Chaco districts of the Durango-Gallup coal field. This large area, all within San Juan County, contains numerous coal beds 5 to 15 feet thick. Ellis2/ mentions the Carbonero (Fruitland in this report) bed in the La Plata-Fruitland district attaining a thickness of 36 feet. This bed has been correlated with the Carbonero bed, formerly mined at Carbon Junction, near Durango, Colo. During the field investigation covered by this report, no operating mine in the Fruitland bed was working a bed thickness of more than 15 feet.

Jan 1, 1957

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By William C. Larson

This Bureau of Mines report discusses uranium in situ leach mining in the United States to acquaint the public with an overview of this emerging mining technology. This report is not intended to be a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. A list of in situ leaching publications is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional basis. Additional information is given that discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining.

Jan 1, 1978

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By Foster Fraas

Almost all minerals show irreversible changes in electrical conductivity after heating in the temperature range 100° to 800° C. This effect can be detected with only a limited number of minerals with the standard ionizing-electrode-type separator, which differentiates between nonconductors and conductors in the single-particle resistivity range of 1011 to 1013 ohms. Tests outside this range with other type separators, such as the static field type, increase the number of minerals with which the effect can be detected to almost all that were tested. Irreversibility may be the result of an alteration of adsorption layers, volatilization of surface cations or anions, or an oxidation or reduction. One example is limonite, which decomposes to hematite and passes through two minima and two maxima in conductivity in the temperature range 100° to 900° C.

Jan 1, 1959

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By James C. Barker

Alluvial cassiterite concentrations are widespread in river gravel and high level terraces within the Ray River watershed. The area lies in unglaciated terrain of Alaska's northern interior. Cassiterite originates from several calc-alkaline plutons of the Ruby batholith. Extensional stresses resulted in graben-like Tertiary basins that were flooded by a 200 ft thick section of mid-to late- Tertiary basalt flows. Basalt blocked local drainages, and 50- to 100-ft of terrace gravel was eventually deposited on top of the flows. Further downwarping and eventual fluvial downcutting of the flows resulted in cycles of accelerated sediment transport, deposition, and reconcentration. Repeated erosional cycles concentrated heavy minerals and resulted in development of tin placers. Preliminary resource estimates of contained tin in Recent alluvium range from 62 to as much as 172 million lbs-Sn in 300 million yd3. Grade of about 90% of the gravels is estimated to range between 0.2- to 0.5- lbs-Sn/yd3. Associated gold and rare earth elements (REE) in monazite and xenotime may be recoverable. Most of the tin is considered a subeconomic inferred resource, though, at least some of the gravels contain 2-to 6-lbs-sn/yd3. Estimates are projected on the basis of surface sampling and several auger drill holes and are provided for the purpose of land-use management planning.

Jan 1, 2011

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Neal M. Muir

The increasing demand for iron ores prompted the Bureau of Mines to investigate the sources of past production in Kentucky to determine whether reserves of usable ore still exist. Preliminary investigation showed that the holdings of the Rose Run Co. were the most promising, inasmuch as the deposit had not been exhausted by past mining and the property was near railroad facilities and but 80 miles from the blast furnaces at Ashland, Ky. The Bureau conducted a churn-drilling and sampling program to investigate the depth, thickness, and iron content of the ore beds so that they might be evaluated as a possible reserve of low-grade iron ores. The Rose Run area in Bath County, Ky., was explored by 74 churn-drill holes totaling 2,059.4 feet of drilling and 4 cuts and test pits. Fifty-seven drill holes and the four test pits penetrated the ore bed at an average depth of 22 feet. The bed had an average thickness of 2.54 feet. Analyses show that the calcium and magnesium carbonate content is more than sufficient to flux the silica and provides an excess that needs an admixture with other siliceous iron ores.

Jan 1, 1950

By Mark Sheppard

This p aver is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different types of primary crushers; and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of the fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By Scott W. Hazen, George W. Gladfelter

This report presents the results of an initial investigation into some problems resulting from the use of assays representing unequal sample interval lengths and the use of the weighted average grade of ore in evaluating bedded mineral deposits . A mathematical proof and examples are given to show that the unweighted and weighted assay averages are equivalent when there is no correlation between assay value and sample interval length but that these averages are different when there is correlation between assay value and sample interval length . The amount of this difference between estimates is a function of the degree of correlation . One set of sample and assay data , based on 11 stratigraphic sections of the Phosphoria formation in Idaho , indicates that the relationship between the amount of difference between estimates and the correlation factor is approximately linear . If this correlation relationship can be established , within acceptable limits of precision , as a consistent attribute of deposits , the estimate of weighted average grade of ore could be predicted directly from the unweighted estimate of grade of ore by using the relationship as a prediction factor . Randomness tests on the sample and assay data from the Phosphoria formation , using the mean - square - successive - difference method , indicate that correlation between assay value and sample interval length ( each sample interval length represents an individual bed or stratum of the formation ) , apparently has little effect on the independence between successive assays , between successive sample interval lengths , and between the products of assays and sample interval lengths . Therefore , these data can be analyzed statistically as long as the original sample sections have been selected at random for sampling .

Jan 1, 1964

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of tie Bruneau River and Jarbidge River study areas, Owyhee County, ID, for the U.S. Bureau of Land Management. The study areas, separated by a narrow corridor, include 90,000 acres of the 107,020-acre Bruneau River Wilderness Study Area (ID-111-17) and 47,000 acres of the 75,340-acre Jarbidge River Wilderness Study Area (ID-17-11). They lie 26 miles and 55 miles, respectively, due south of Mountain Home, ID. Approximately 38 placer claims for gold and 182 lode and placer claims for jasper, agate, and limestone were located within and adjacent to the study areas from 1893 to 1981. Currently, there are eight mining claims for jasper at Indian Hot Springs along the corridor between the study areas.

Jan 1, 1987

By Sumner M. Anderson

THE ENORMOUS contrast between the mineral economy of Cuba in 1963 and in 1958 was the result of the overall Political changed to which the total economy of the country was intimately lined. Creation of the Cuban Mining Institute (Instituto Cubano de la Minería) to direct all mining activities in the country was an early act of the new Government after the revolution on January 1, 1959. During the next 2 years, the Government confiscated foreign holdings,2 including Unite States investments exceeding $1 billion in value. Foreign mining and metallurgical technicians-predominately from Communist areas-were brought in to reorganize the mineral industries. On January 3, 1961, diplomatic relations between Cuba and the United States were severe and then on May 2, Cuba announced its full-fledged membership in the so-called Communist Bloc. Fifty-four international treaties assured Cuba of Communist economic support, technical and financial assistance, machinery, raw materials, and manufactures. The Soviet Union agreed to buy some Cuban mineral products, and Czechoslovakia stated that it would buy all mineral production offered for the next 20 years, but in both cases at prices said to be much lower than the world market. The mineral productivity segment of the mineral economy during and since the period of political metamorphosis, has withstood the political disruption better than has the economy as a whole, but with no direct measure of the magnitude of its cost. The overall economic record is marked with steady deterioration; the annual average per capita income has dropped from $374 in 1957 to $185 in 1963, when Cuba's deficit with the Soviet Union alone reached an admitted $1 billion.

Jan 1, 1964

By W. T. Benson

The Bureau of Mines has examined selected deposits of titanium minerals throughout the United States. The titaniferous magnetite deposits in the western San Gabriel Mountains, Los Angeles County, Calif., were among those selected for study, and in 1956-58 field work was conducted to determine the extent and character of the titaniferous magnetite deposits occurring in the area. This report describes this work and summarizes earlier work in the area by the Bureau and others. The titaniferous magnetite occurs disseminated as seams and lenticular pods in an anorthosite belt 4 to 6 miles wide that trends about. N. 80° W., extending from sec. 13, T. 3 N., R. 12 W., to the west boundary of R. 14 W., at which point the titaniferous magnetite-bearing rocks disappear beneath the sediments in the Santa Clara River Valley.

Jan 1, 1962

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981