Search Documents

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By Beatrice L. Lukens, David Schlain, John D. Prater

"The electrolytic manganese process developed by the Bureau of Mines4/ and now in use in the commercial plant of the Electromanganese Corp. at Knoxville, Tenn., and in the Bureau of Mines pilot plant5/ at Boulder City, Nev., involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes.. The spent electrolyte contains, in addition to the sulfuric acid, approximately 30 percent of the manganese and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been given a reducing roast. The resulting leach liquor is purified and returned to the cell.Since the presence of small amounts of certain impurities in the electrolyte may be very detrimental to the electrodeposition of manganese, the purification of feed solution is a very important step in the process. According to the purification method6/ now in use in the Bureau of Mines pilot plant at Boulder city, Nev., cobalt, nickel, iron, arsenic, lead, copper, etc., are removed by precipitation as sulfides at a pH of 6.0 to 6.5. Residual sulfides and colloidal material are removed from the resulting solution by ferric hydroxide formed by adding a small amount of iron sulfate and passing air through the solution. Feed solution purified in this way contains less than 1/2 mg.-per liter-of such impurities as arsenic, iron, cobalt, nickel, copper, etc., and is pure enough to give consistently excellent manganese deposits.Although this purification scheme has given satisfactory results at the Boulder City pilot plant knowledge of the specific effects of various impurities would be valuable. Such information would be useful in diagnosing the causes of cell room operating difficulties, and might aid in the recognition and correction of impurity difficulties arising from the use of new ores.. The purpose of this investigation was therefore, to study the effects of various concentrations of some common impurities.Since the effects of some impurities may not be apparent during short deposition periods and since harmful impurities often cause erratic results rather than consistently poor ones, it was believed that conclusions concerning the effects of impurities should be based upon the results of a fairly large number of 20- to 24-hour tests. Because of the time required for such tests, it was necessary to limit the scope of the work to a few of the more common impurities."

May 1, 1946

By S. H. Ash

[On December 2, 1932, the Governor of California called upon the representatives of the mining industry of the State to attend a meeting at Sacramento to discuss ways and means of assisting is relieving some of its perplexing and extremely distressing problems, particularly the mounting cost of accidents which faces the industry with an industrial insurance rate for classification of $11.85 per $100 of pay roll, effective January 1, 1033. The significance of this fact is at once apparent when it is realized that the classification rates per $100 of pay roll for mining have steadily increased for some time, as follows: $3.91 in 1924, $5.54 in 1925 and 1926, $8.04 in 1927, $8.53 in 1928, $9.05 in 1929, $9.42 in 1930, $10.54 in 1931, $10.99 in 1952, and $11.85 in 1133. In other words, the cost rates have acre than doubled, wile statistics indicate that the accident rates nave shown an entirely different trend. At the meeting mentioned, one of the management officials sounded an effective keynote when he declared that a spade should be called: a spade. The perplexing problems of any industry can be approached best and remedies applied if that policy is kept to the front. It is appropriate to mention that high accident rates and a decrease in wages in recent years have unquestionably accounted in part for a unit cost rate, on a pay-roll basis; it also is well to explain that the policy years3 1926 to 1930, inclusive, are the years on which the accident-cost experience for 193: is based. That accident rates :lave not undergone the expected beneficial chance in California's experience is apparent in the words of a Bureau of Mines report:4]

Jan 1, 1933

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

By B. R. Mohal, F. F. Aplan, S. Chander

"ABSTRACTThe wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5 ] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3( CH2 )8-C6H4,- ( OC2H, ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3)2-C6H4- ( OC2H4) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 to determine the effect of surfactants on wettability of cotton fibers. In this procedure commonly known as the Draves test, the concentration of a surfactant required to give a 'sink time' of 25 s is determined.Other investigators have used slight variations of the Walker method to study the wetting of fine particles [ 8-12 ] , by measuring the time for wetting a given amount of powder. There are differences in the manner in which the time of wetting is measured, however. Some investigators measure the time for the last trace of coal to disappear [ 8,11 ] whereas others determine the time for the vast majority of particles to sink [ 10 ] . Some investigators report a wetting rate [ 11 ] which is a value calculated on the basis of the time for the 'last traces of particles to sink'. The differences in choice of criterion for wetting can result in different values for wetting rates as illustrated in Fig. 1 which is based upon our measurements of the amount of powder wetted as a function of time. The procedure for wetting rate measurements is described in the next section. The technique in which time for disappearance of the 'last traces of particles' is determined gives the smallest value for the wetting rate, while the technique in which the time for wetting of the 'vast majority' of particles is determined will give intermediate rates. The terms 'last traces of particles' and 'vast majority of particles' are usually not defined explicitly and can lead to large differences in wetting rates measured by different investigators. Since our measurements show that the wetting rates for an assembly of powder decreases with time, we have used the initial wetting rates to compare the wetting behavior of coal in solutions of different surfactants."

Mar 1, 1989

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By Oliver Bowles

"Conservation of slateWaste slate is a problem of outstanding importance in the slate industry, for a very large proportion of all slate quarried is thrown on the waste heap. While many uses for waste slate have been found, the demand calls for merely a fraction of the present supply of unused material. If the slate industry is to increase in prosperity, the producer's energy must be directed toward the development of ways and means of reducing waste to the lowest possible point. The Bureau of Mines of the Department of the Interior has devoted much study to this problem and a recent bulletin ** contains a detailed discussion of the waste problem.Attention has recently been directed toward an improved method of cutting slate in quarries, a method that promises to reduce greatly the percentage of waste material. The method has been introduced since that bulletin was published, and this supplementary paper covers the details of the process.A reversion in method,In connection with this new mode of operation history is repeating itself in a very interesting way, for the old quarry bar used years ago with steam drills, and later discarded in favor of the channeling machine .and the hammer drill, has been salvaged from the scrap heap, and again put to active use. The occasion for its employment is an attempt to improve quarry methods by the substitution of drilling for channeling or blasting."

Oct 1, 1923

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Clinton C. Knox

The Townsite mine, consisting of 40 acres in the town of Cardin, Okla., is in the center of a highly productive part of the Picher-Cardin district of the Tri-State zinc and lead field. Previous to the time of the work done by the Bureau of Mines, the property had been partly explored by churn drilling, and an area-of about 8 acres in the southwestern corner had been exploited by underground workings. The Bureau of Mines investigation had as its object the more intensive development of the northern part of the property where previous drilling had indicated a possible ore deposit of commercial grade. Churn drilling by the Bureau began in September 1942 and continued to February 1943. Twenty holes totaling 4,827 feet of bore were completed. Utilizing the information gained from these drill holes, the Weidman Mining Co., lessee of the tract, sank a shaft and proceeded to the exploitation of the indicated ore bodies.

Jan 1, 1949

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974

By W. G. Sandell, G. M. Potter

"As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agencies engaged in purchasing and stock-piling some of the more critical and strategic materirals. At the request of George A. Easley, representative of the MetalsReserve Company, beneficiation studies were made on a sample of complex tin-tungsten ore from the Urania mine in Bolivia, South America.The low-grade Urania ore (1.9 percent Sn and 1.55 percent W03) contained a very complex of cassiterite and scheelite with iron sulfidesand quartz. The problem involved in concentrating this ore was the removal of sulfides and silica by stage flotation and gravity concentration for the production of a marketable tin-tungsten concentrate. The sulfides and primary quartzite were readily rejected, but the secondary quartz was intimately associated with cassiterite, and ultimate recovery depended on treatment of minus 560-mesh (theoretical) sizes.The ore was amenable to concentration by ore dressing. Seventy percent of the tin and 83 percent of the tungsten were recovered in a product that assayed approximately 20 percent Sn and 20 percent W03 and that met grade ""F"" specifications of the Metals Reserve Company for mixed tin-tungston concentrates."

Feb 1, 1948

By Perry G. Cotter

As a portion of a general program for the synthesis of hard materials, a method was sought by which the hardness and density of tungsten carbide (WC)-cobalt compacts could be increased. It was demonstrated by Cotter that these improvements in quality could be made by employing an electric-resistance sintering process in which heat and pressure are applied simultaneously to presintered compacts composed of powdered tungsten carbide and cobalt. This conclusion was based on tests of material prepared by Cotter on welding equipment in use at the U. S. Naval Engineering Experiment Station, Annapolis, Md., and at Rensselaer Polytechnic Institute, Troy, N. Y. Rockwell-hardness tests made at Norris and core-drilling tests made at the Mount Weather Station of the Bureau of Mines indicated that, for some purposes, carbide material made by this process might be superior to the chemically analogous commercial products prepared by ordinary sintering methods. A program to develop optimum conditions for the electric-resistance sintering of tungsten carbide-cobalt compacts was initiated. The program was followed by a systematic evaluation of the hardness and density of compacts prepared by this method along with a series of carbide compacts furnished by various manufacturers. This paper presents a description of the electric-resistance sintering of tungsten carbide-cobalt compacts and the results of comparative physical tests.

Jan 1, 1955

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By A. J. Barry

An apparatus and procedure have been developed for testing the anchorage effectiveness of slotted-type bolts. The apparatus consists of: (1) A hydrualic Jack assembly for loading the bolt and (2) a device (extensometer or cathetometer) for measuring displacement of the bolt as it is loaded. This apparatus and procedure permit measurment of anchor slip for loads up to the yield load of the bolt. Two representative makes of slotted-type bolts (a total of 94 bolts) were tested in typical sandstone and shale mine roof. Analysis of the test results showed that (1) anchorage capacities up to the yield load of the bolts can be developed in either rock type; (2) the shape of the slotted end of the bolt affects the ease with which the bolt can be driven; (3) all bolts for which the driving distance was more than 1.25 inches produced satisfactory anchorage in both rock types (thus, driving distance can be used as a criterion for satisfactory anchorage); (4) for the group of bolts that was satisfactorily anchored the anchor slip was unaffected by the type of bolt but was considerably larger in shale than in sandstone; and (5) the bolt expansion, that is, the amount the wedge expands the prongs in excess of the diameter of the hole, can also be employed as a criterion for satisfactory anchorage. Although the bolt-expansion and driving-distance results do not differ appreciably, the latter is recommended because it is easier to determine.

Jan 1, 1954

By P. A. Cox

Guidelines are provided for the design of explosion-proof electrical enclosures that will meet MSHA certification requirements according to Part 18, Title 30, of the Code of Federal Regulations, and fulfill their intended service underground. The guide covers only those aspects of design which affect enclosure strength, ruggedness, endurance and flame path, i. e., the enclosure ability to properly contain an internal explosion. Internal static and explosion pressures, external impact and thermal heating load are treated as well as the proper selection of materials and welding procedures.

Jan 1, 1985

By Q. H. Forbes

"The high injury rand fatality rate in coal mining, as compared with other industries, has caused the mining industry to become more and more interested in accident prevention methods.The prevention of accidents in the mining industry is probably not as simple a problem as it is in other industries, but if the experience of coal mining companies who have taken up the work of accident prevention seriously during recent years means anything, there is little doubt that most mining companies car improve their accident records very materially.Such results can be obtained in practically all instances without adding to production costs. In fact, there is little doubt that a well-organized program of accident prevention Will bring about a 'material production cost reduction due to increased efficiency, lower labor turnover, fewer delays due to accidents, better satisfied workmen, and a direct saving in compensation costs as well as many other items of expense.The more closely a. person is connected with the work of accident prevention, the more he becomes a believer in the value of amity in human relationships and the more he is able to exercise a spirit of toleration, fairness, justness, and helpfulness toward the problems of others, whatever those problems may be. Human nature responds to just these expressions of good willAnother great and invaluable effect of working for safety, is the fact that it is building up in the mind an appreciation of that which is constructive and, conversely, in opposition to that which is destructive In other words; the person who is sincerely striving to prevent accidents because they are destructive, costly, tad injurious, is subconsciously training his mind to look on any proposition from a constructive point of view. Working for accident prevention and safety is about the finest social training any person can have. It does not make a Person a financial Wizard or an executive genius, but it does make for the highest type of citizenship.While humanitarian reasons alone should be sufficient to maze accident prevention work an important factor in every mining organization, there are other reasons as well, since it has been proved conclusively that there can be no efficiency and economy without safety, as somebody pays when safety is lacking. Every safety device pays dividends; every safety application evaded is an assessment and a loss. Dangerous conditions are the most expensive and extravagant conditions in or about a coal mine. The economic gains are of considerable interest to all coal mining companies and this is brought about as before stated--through decreased compensation rates, the reduction of labor turnover, etc."

Dec 1, 1930

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987