Search Documents

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By Horace C. Porter

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantities, a series of tests was begun in the fall of 1909 under the supervision of J. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for example, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New River (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a full account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included.

Jan 1, 1917

By Horace C. Porter, F. K. OVITZ

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantitieS', a series . of tests was begun in the fall of 1909 under the supervision of tT. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for exaIp.ple, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New R~ver (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a fu11 account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included. The tests of New River coal, in cooperation with the Navy Department, were undertaken to determine the advantage to be gained by storing coal under water, and particularly under salt water. Small lots were used in order to make the tests of maximum severity, and parallel experiments were made with run-of-mine and crushed coal under one-fourth inch size. All of the small lots tested under the different conditions (except those tested near Key West, Fla.) were taken as representative portions from one large original lot. The tests of Pocahontas coal, which, like the New River, is semibituminous, were undertaken chiefly to determine th.e effect of the tropical conditions in Panama. They were made on an outdoor pile of 100 tons of run-of-mine coal. Pittsburgh gas coal, a high-volatile, bituminous type used at gas and by-product coke works, was exposed for test at Ann Arbor, Mich., in cooperation with the University of Michigan. The university agreed to make tests at successive intervals of storage to determine, in its illuminating-gas experiment station, the yields of gas and byproducts from the coal. The coal, screened lump, was stored in about 4-ton lots out of doors in open bins. Subbituminous coal, which is mined in Colorado, Wyoming, and other States, and is known also as "black lignite," is commonly supposed to deteriorate rapidly in storage, especially by "slacking" or crumbling of the lumps. The tests herein described were undertaken at Sheridan, Wyo., in cooperation with the Chicago, Burlington & Quincy Railroad Co., in order to determine the extent of this slacking and the accompanying loss of heat value. The tests were in open bins holding 4 to 12 tons.

Jan 1, 1917

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By W. L. Crentz

In Fayette County, the Pittsburgh bed has been the major source of production for almost two centuries. Although historical documentation is not available, there is evidence, that the Pittsburgh bed may have been discovered in Fayette County near Mt. Braddock, Pa., as early as 1753. The earliest known reference to coal in western Pennsylvania was recorded in 1758 by a Quaker trader, James .Kenny, who reported having seen coal in Fayette County. The production of coke from Pittsburgh coal was begun in 1841, when two 10-foot beehive ovens were erected in the Connellsville region to make coke .for shipment by river to the market. The Connellsville, region extends from Latrobe, Pa., in Westmoreland County to South of Uniontown, in Fayette County. Connellsville coke was used with great success in the Clinton furnace in 1859.

Jan 1, 1951

By E. P. Carman

1. CARMAN, EVERETT P., OPPERMAN, MARTHA, NISHIYANA, SALLY, AND RACOOSIN, LEE. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1945 to 1950. B. 528, 1954, 60 pp. 40 cents. 2. ROSE, HAROLD J. Industry-Sponsored Coal Research in the United States. Chap. in Proceedings: Fifth International Conference of Directors of Mine Safety Research. B. 489, 1950, pp. 9-12. $1.25. Minerals Yearbook 3. STRINER, HERBERT E., CARMAN, E. P., AND GOODING, RICHARD M. Review of the Mineral-Fuel Industries in 1952. Minerals Yearbook 1952, Fuels, vol. 2 (pub. 1954), pp. 1-28.

Jan 1, 1958

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By R. T. DeWoody, J. W. Chester, W. C. Miller

The work was done to develop a relatively efficient muffler for quieting the exhaust of a rock drill . The exhaust of a pneumatic rock drill is the source of the major part of the noise generated by the drill . The exhaust noise can be reduced in a number of different ways , but this study involved only reactive mufflers . The reactive muffler can be simulated by an electrical circuit . Information obtained from analogous electrical circuits was used to design an efficient exhaust muffler for pneumatic rock drills . Electrical analogies proved to be a valuable tool in the design of mufflers .

Jan 1, 1964

By Charles L. Kimbell

Virtually every available measure of total world mineral industry activity demonstrated that 1982 was little, if any, better for the industry than 1981 had been. Levels of production, trade, and consumption for virtually every major commodity declined; unit prices for most commodities fell, particularly in terms of constant dollars, and as a result of cutbacks in output and lower prices, capital available for investment within the industry was reduced. These conditions, coupled with the existence of considerable idle capacity, tended to retard investment, although there was an upturn in U.S. oil industry investment overseas. Despite the overall depressed situation of the world's mineral industry, there were indications of possible improvements in market economy countries near yearend, as output of some materials increased marginally and as prices for some mineral commodities reversed their downward trends. The downturns in total world mineral industry activity were not universal from the viewpoint of individual countries. Indeed, output of a number of commodities increased in centrally planned economy countries, and these gains were insufficient to offset declines in market economy countries, thereby sharply altering the proportion of total world output accounted for by each of these two groups of countries. There was a similar shift in consumption on a percentage basis.

Jan 1, 1984