Search Documents

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By Seth T. Reese

REPORTS received from operating companies by the Bureau of Mines, United States Department of the Interior, indicated marked progress in the reduction of injuries to employees in the coking industry in 1951 as compared with 1950. The fatality rate (0.14) per million man-hours of exposure declined 33 percent and was the second best performance since statistics on the industry were first collected in 1916. The nonfatal-injury rate (10.94), the best since 1940, declined 8 percent and was bettered only in 8 of the past 36 years. The nonfatal rate is based on all injuries resulting in loss of time for more than the remainder of the day on which the injury occurred. The exposure to hazard, as represented by the number of man-hours of work time during the year, was 7 percent higher than in 1950 and, except for the year 1943, was the highest since 1920. The fatality rate for men employed at beehive-coke ovens decreased 16 percent and the nonfatal-injury rate 23 percent, while the man-hours of work time or exposure increased slightly over 16 percent. The fatality and nonfatal-injury rates at byproduct ovens declined 33 and 2 ½ percent, respectively, while the number of man-hours worked increased 6 percent.

Jan 1, 1954

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By R. A. Cattell

The Bureau of Mines recently observed its fortieth anniversary, and with the close of the fiscal year 1950 it completed 36 years of close cooperation with and helpfulness to the petroleum and natural-gas industries, whose technical problems it studies. Petroleum people likewise observed the ninetieth anniversary of the start of this truly American industry when "Colonel" Drake drilled the first well at Titusville, Pa., in 1859 (see fig. 1). Throughout the period, during which there have been many changes in the fuel and related economy of the country, this work has been carried on systematically by an organized entity of the Bureau first known as the Petroleum Division and in recent years as the Petroleum and Natural Gas Branch. Changes in the industries have been brought about partly by economic forces, partly by advances in technology, and in some measure by the impact of two world wars. As the needs of industry and the Nation have changed, so have the studies of the Bureau changed to meet these needs. Consistently, Bureau technologists and scientists have tried to keep in step with progressive movements; frequently, in fact, have taken the lead. Wherever possible, they have looked far ahead in their program of research, at the same time recognizing the needs of the hour.

Jan 1, 1951

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965

By William L. Crentz

In the past, Westmoreland County together with Fayette County produced about one-third of the bituminous coal mined in Pennsylvania. The Pittsburgh bed in Westmoreland County has furnished enormous quantities of coal to the by-product and beehive ovens, gas-manufacturing plants, and general industrial manufacturers over a wide area until about 20 years ago. Little attention was paid to the thinner beds because of the superior quality of the Pittsburgh. The approaching exhaustion of Pittsburgh coal will require accelerated-exploitation of these coals if Westmoreland County is to continue as an important source of bituminous coal, Much of the Pittsburgh coal in Westmoreland County is low-sulfur and requires no mechanical cleaning for the preparation of a metallurgical fuel. Even those areas where the sulfur percentage increased to a maximum of about 2 percent, a relatively easy washing operation usually produced a cleaned coal, which found ready acceptance by the coke industry. Davis reported the remaining recoverable reserves of the .Pittsburgh bed in Westmoreland County to be 255,439,000 tons as of January 1, 1937. Since that date, more than 100,000,000 tons of Pittsburgh coal has been extracted so that the time is not too distant when this important coal bed will be depleted. A study of the Pittsburgh bed in Westmoreland -County has not been made a part of this report as the remaining reserves of the coal can be used in coke making with a, minimum of preparation. The production from the Upper 'Freeport bed will increase as the supply of coal from the Pittsburgh bed diminishes, and as of the present time it supplies a substantial proportion of the county's coal output.

Jan 1, 1951

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By C. M. Harrer

Reconnaissance investigations were made of 129 iron occurrences in Arizona to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential western iron markets are discussed. The location, features, qualities, extent, and potential of iron occurrences and some associative resources--limestone and dolomite, coal, petroleum and natural gas, power, and water are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic or pyrometasomatic replacements of calcareous Paleozoic to Proterozoic rocks associated with intrusives. Large low-grade deposits of great potential are present as Precambrian taconite, semitaconite-, and jaspilite-like iron formations of magnetite-hematite. Iron occurs also as low-grade concentrations of magnetite in extensive alluvial deposits. Nonferrous metallurgical slags, nearly 100 million tons, are considered a potential source of iron. Various accessory elements are associated with the iron minerals and these pose metallurgical and economic problems.

Jan 1, 1964

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By James D. Cooper

COMBINED tonnage or natural abrasive materials sold or used in the United States in 1962 was 10 percent greater than that of 1961 and value was 9 percent higher. Production of crude artificial abrasives in the United States and Canada was up 14 percent in volume and 9 percent in value. Value of grinding-wheel sales increased 13 percent, and the value of coated-abrasives sales was up 10 percent. The value of imports and reexports declined, while the value or exports increased. [ ]

Jan 1, 1963

By C. C. Clark

This report presents the results of tests conducted by the U.S. Bureau of Mines to determine the transport characteristics of highly concentrated paste backfill mixes made from dewatered total mine tailings. The slurry concentrations of the mixes were all above 78 pct by weight with slumps ranging from 6.4 to 16.5 cm (2.5 to 6.5 in). Laboratory material property tests and full-scale pumping tests were conducted using pipe diameters of 102, 128, and 154 mm (4, 5, and 6 in) and a positive-displacement pump. The results indicated that the tested backfill mixes can be successfully transported as a stiff paste and identified the influence of and the interaction among the various mix and system variables.

Jan 1, 2010

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Wilbur I. Duvall, S. L. Windes, Leonard Obert

"Previous investigations, too numerous to be listed in entirety, have been performed to determine the physical properties of rock. When considered according to their objectives, most of these investigations can be grouped as follows: First, the geologic group (1,2),4/ in which the purpose was to obtain information on the physical properties of the rocks that make up the earth's crust. Particular emphasis has been placed on the determination of the elastic constants--that is, Young's modulus, the modules of rigidity, and Poisson's ratio – as these quantities determine the propagation characteristics of seismic waves. Second, the structural properties group (3 - 11), in which the physical properties of architectural or monumental stone, concrete and aggregate rock, road blocks (cobblestone), and the like were desired. The tests have been quite general and include, besides the elastic properties; the compressive and tensile strength, and the toughness, hardness, and weathering properties of many types of rocks.To .a lesser degree, investigations have been carried out to determine the physical properties of mine rock. A few reports (12 - 14) present data on the crushability and grindability of mine rock, and a large number of papers discuss grinding and crushing procedures and methods of analyzing the data (for example, see references 15 - 17). Some of the latter group also have given the results of tests on mine rock; however, comparatively few include an adequate petrographic description or information on other physical properties of the rock. A few papers,(18 - 22) have reported studies of the strength of rock specimens in respect to the strength of parts of mine structures, such as pillars, roof, arches, etc. Other papers (23 - 26) have discussed investigations on such subjects as primary and secondary crushing, diamond and pneumatic rock drilling, explosive breaking and shattering of rock, rate of drifting and miring, and other allied problems. The majority of these reports have given no more than a cursory, description of the rocks and have included no statement regarding the physical properties. When statements have been given regarding the physical properties, they have usually referred only to isolated tests, making correlations between variations in the physical properties and variations in the .test under consideration difficult, if not impossible. Some reports have included handbook values on such characteristics as the crushing strength, hardness, and toughness. This practice is not satisfactory, because these values are usually given for col¬lective types of rocks, such as granites, limestones, and marbles, and it is known that the variations of the physical properties within these groups is often larger than the differences between the groups."

Aug 1, 1946

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951