Search Documents

By R. V. Ramani

This volume is the second of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. The dragline model described in this report simulates the movement of the dragline bucket across the digging face, the swing load, the dump, and swing back. It is programmed to handle chopdown, key cut, main cut, and rehandling operations. Provisions have been made for simulating equipment and mining delays. Any mining method can be specified in terms of numbered blocks, the dragline positions for the mining block and the dumping location for the block. Accounting procedures permit the calculation of production rates, rehandle volume, dig and delay times. The model can be used to study the effects of varying mining conditions, cut width, and spoiling sequence with special reference to toxic spoil, overburden and bench removal procedures. The basic input data for the model include machine parameters, the geology and material characteristics, the mining parameter, and the delay characteristics of the equipment.

Jan 1, 1985

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By William E. Eckard

Production of oil from a narrow shoestring sand presents problems unique in the oil industry. Especially important, from both an engineering end an economic standpoint, are the limitations imposed upon well patterns and spacings by the shape of the field. This report concerns a study of the Paola shoestring, Miami and Franklin Counties, Kane., where well density of 0.85 acre per well was not uncommon to insure profitable primary recovery in a reasonable time. However, such a great number of wells increased the operator's investment and reduced his profit considerably. It was the purpose of this study to investigate various well patterns and spacings applicable to water-flooding a shoestring reservoir and the effect of these factors upon recovery of oil and the most profitable operation of the pool. The designer of well patterns for a shoestring sand should evaluate carefully the edges of the shoestring, even though they may be considered too thin to drill. These comparatively thin edges contain large quantities of recoverable oil; moreover they are resaturated with oil as the pool is water-flooded.

Jan 1, 1951

By Matthew J. Sheridan

The Bureau of Mines study described in this report was conducted in the Denver, Colo., area (1) to summarize existing conservation practices as related to the most beneficial utilization of deposits of sand and gravel; (2) to identify the conflicting positions of the aggregate producer, the mineral owner, nearby residents, and local government officials responsible for determining land status and for issuing operating permits; and (3) to show the need for planning in Denver and in other expanding communities toward obtaining the benefits of conservation of our rapidly dwindling mineral resources. In order to determine the effects of urbanization on the Denver aggregate industry, interviews were held with owners of sand and gravel operations, with producers of concrete and bituminous pavement, with city and county planning and zoning personnel, and with representatives of various interested organizations. The conservation and ultimate utilization of deposits of construction raw materials near expanding urban areas can best be accomplished by long-range land-use projection and the requesite cooperation of technically advised planning and zoning administrators, government officials, mineral producers, and land developers.

Jan 1, 1967

By R. A. Cattell

With the activities of the Petroleum and Natural Gas Division geared chiefly to problems directly connected with the war effort , the emphasis of the work under oil and gas development and production was to make engineering studies of selected reservoirs for the Petroleum Administration for War , to determine the extractable quantities of components in them, and to study the characteristics of these components for use in the manufacture of aviation gasoline and other products . The needs of the Petroleum Administration for War and the operators for specific data from gas - condensate fields were fulfilled , and , in addition , engineering data along lines of a forward - looking program of research on reservoir behavior were collected , which should be of great value in the postwar period . It is planned to publish many of these data as soon as conditions permit . The work of the Secondary Recovery Section had as its objectives in- . creasing the rate of production of crude petroleum and , which is more important , preventing the premature abandonment of wells in " stripper " and marginal According to the National Survey of Stripper Wells by the National Stripper Well Association in cooperation with the Interstate Oil Compact Commission , a total of 67,460 stripper wells was abandoned from January 1 , 1935 , to July 1 , 1942 , inclusive , with an estimated loss in proved reserves of approximately 216 million barrels . This survey also indicates that over 1.2 billion barrels of oil would be recovered by primary production from more than 290,000 stripper wells then in operation , and an additional 2.5 billion barrels of oil could be recovered from them by secondary production methods . The work of the Chemistry and Refining Section was oriented towards the optimum utilization of crude oils in the manufacture of aviation fuels for spark-ignition and jet - propulsion engines . The work involved intensive studies of superfractionation , hydrocarbon analysis , and the engine testing of fuels . Particular attention was given to the effect of sulfur compounds in the crude oils and in the fuels made from them . The research on thermodynamics is concerned with the experimental determination of precise and accurate values of the fundamental thermodynamic constants of pure hydrocarbons and related compounds . The data obtained in these investigations will be utilized for devising and improving chemical processes in which petroleum hydrocarbons are the raw materials . Without such data , much time and expensive material and equipment may be wasted in attempts to obtain reactions under conditions that the laws of thermodynamics rule out of consideration . Thermodynamic data are useful and required in the petroleum industry for calculations of heat balances in the design of furnaces , fractionating towers , and heat- transfer equipment . It is of utmost importance , also , to know the heat requirements of cracking and other chemical reactions so that heat may be supplied or dissipated in the proper proportions . These needs for thermodynamic data are being recognized more and more by petroleum -refining engineers . The responsibility for the production of helium for the Navy , the Army , other governmental agencies and non-Federal users is vested in the Bureau of Mines by an Act of Congress ( 50 Stat . 885 ; 50 U.S.c. 161-166 ) . The Helium Subdivision of the Petroleum and Natural Gas Division continued to meet all demands for helium .

Jun 1, 1949

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the ninth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township map. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By Frank L. Wideman

This information circular describes methods used in mining inclined beds of phosphate rock in mines operated by San Francisco Chemical Co. in Rich County, Utah. The mines are on the western flank of the Crawford Mountains, a short, narrow range in northern Utah near the Idaho-Wyoming corner (fig. 1). The western front of the range is a conspicuous wall of folded and faulted sedimentary rocks that rises abruptly 300 to 600 feet above the floor of the adjacent Bear River Valley. Rex Peak, highest point in the range, is approximately 8,000 feet above sea level. The area surrounding the mines is sparsely populated. Randolph, the county seat of Rich County, has a population of 650. It is 10 miles southwest of the mines by road and the only town in their vicinity.

Jan 1, 1958

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By Michael Rieber

Rail cars are referred to as "yellow-balled" when they are sufficiently old or damaged to preclude their efficient operation on long-haul or main line routes. For most coal carrying railroads, their alternative value is salvage. This, however, does not necessarily preclude their effective use, on a limited basis, by small mines located near existing trackage. Because of age, the sizes of these hopper and gondola cars ace currently 50 and 70 tons rather than the 100 tons commonly built at the present time. As a gathering system, yellow-ball rail could provide an alternative, particularly in Kentucky, western Pennsylvania and west Virginia, to coal trucks, conveyor belts and pneumatic pipelines [4, p.17], belts and pneumatic pipelines. Rail service of this type provides a limited alternative to track abondonment, a possible financial return to a railbank [3], a direct contribution to service demand on main lines, and a means by which many small eastern coal mines could retain or regain competitive viability [4]. In terms of energy efficiency, compared to trucking coal, the total direct energy impact (fuel) of yellow-ball rail can be expected to range from 280-990 Btu/ton-mile while that for trucks ranges from 1850-3120 Btu/ton-mile [2].

Jan 1, 1977

By Oliver Bowles

"Properties and Uses.Iceland spar is a name given to a pure crystallized form of calcite (CaCo3) which is sufficiently transparent and free of defects to be used in the manufacture of optical instruments. While the actual requirements are small, the degree of purity and physical perfection demanded renders it somewhat difficult to obtain suitable material.The properties of value in Iceland spar are its transparency combined with double refraction. It is used in the manufacture of polarizing microscopes, saccharimeters, colorimeters and photometers. Its most important use is in the manufacture of Nicol prisms, which constitute an essential part of every polarizing microscope. The principle governing the construction of the Nicol prism is as follows:Ordinary light in passing through a crystal of calcite is resolved into two rays of plane polarized light vibrating in planes at right angles to each other and having different indices of refraction. Thus the two rays follow different paths through the crystal. The prism of Iceland spar is cut diagonally and cemented together again with a transparent cement having an index of refraction intermediate between the two rays passing through the prism. Canada balsam is employed for this purpose. The prism is cut at such an angle that the ray having the greatest index of refraction meets the surface of the balsam at an angle greater than the angle of total reflection, and it is thus deflected to the side of the prism, while the second ray passes through. Thus one of the rays is eliminated and polarized light vibrating in a single plane is obtained."

Apr 1, 1920

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933