Search Documents

By Joseph Grumer

An instrumented spherical vessel has been used for many years to study laminar combustion waves. Concurrent measurements of flame speed and pressure-rise rates have led to evaluations of burning velocities, the pressure dependence of the burning velocity, and the expansion ratios of the gases passing through the combustion wave. For the most part, these studies have involved flames initially at atmospheric or subatmospheric pressure. The old spherical vessel used by the Bureau of Mines was not designed for use at elevated pressures. Moreover, being made of wrought iron, it was susceptible enough to corrosion to prohibit its use with many combustible mixtures that figure in industrial research. In mid-1956, under sponsorship of the Office of Naval Research, the Bureau undertook the development of a stainless steel spherical vessel capable of withstanding explosions of gaseous mixtures at initial pressures as high as 20 atm. and initial temperatures as high as 250° C. The design called for a double array (cross) of closely spaced small windows for observation of the flame as it traversed the vessel and a piezoelectric transducer to measure concurrently pressure-rise rates. Because no commercial contractor was willing to bid on the construction of such a vessel, it was built at the Bureau's Bruceton machine shop.7

Jan 1, 1961

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By Vinit Mody

The belt conveyor is one of the major pieces of equipment for transferring bulk material in mining operations. However, considerable amount of respirable dust may be generated whenever the bulk material is loaded, dumped, or transferred. This report identifies and evaluates various dust control technolgies applicable to belt conveyors, and describes how an integrated systems approach can reduce dust emissions at a transfer point. Phase I of the program consisted of literature search and a critical evaluation of various dust control technologies. The work established that a comprehensive approach to calculating exhaust volumes for dust collection system does not exist. The parameters that affect the wet dust suppression efficiency were also reviewed. Based on the Phase I work, bulk material handling system and dry dust collection or wet dust suppression systems were designed and installed at a number of transfer points in a limestone processing facility, a surface mine selected as a field test site. Field test data were used to determine the validity of various exhaust volume calculations at the different transfer points. The field test data also formed the basis for the evaluations of the relative effectiveness of commercially available and wet dust suppression systems in controlling respirable dust emissions.

Jan 1, 1984

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By James C. Barker

Unverified reports of rare earth element (REE) concentrations in gold placers and radioactive mineral prospects in the Zane Hills were investigated by the U.S. Bureau of Mines as part of the Alaska critical minerals program. REE is reported to occur in dredge concentrates at the Hogatza mine and up to 1.2 pct REE was previously analyzed in alkalic syenite (bostonite) dikes marginal to the pluton. In addition, numerous thorium-rich veins, explored for their uranium content but unevaluated for REE, occur on the western margin of the Zane Hills. The Bureau mapped and sampled all of the reported or suspected REE occurrences. Dredge concentrates contain abundant uranothorianite, a mineral species which incorporates cerium subgroup REE. Bostonite dikes occur in conjunction with a multi-phased zoned alkalic intrusion, however, no significant REE concentrations were found. Thorium-rich veins contain nil to 0.5 pct Y but resource potential is limited by this relatively low grade, the ultimate low tonnage potential, and the lack of uranium as a major economic element. The Zane Hills exhibit attractive exploration targets for uranium deposits, primarily in a sedimentary form. Gold may be found peripheral to the pluton in both placer and lode deposits. Resource potential of REE, however, appears limited to a placer by-product of REE-Zr-Ti that is recoverable only during large scale gold placer mining. Placer exploration of the lower Wheeler and Dakli Creeks is suggested.

Jan 1, 1991

By Thomas J. Peters

A mineral survey of the Sill Hill RARE II area (No. 5304), covering 5,200 acres (2,100 ha) of the Cleveland National Forest, San Diego County, California, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey. This survey was in conformance with the Resource Planning Act (RPA) of 1974, as amended by the National Forest Management Act of 1976, to provide mineral resource information for study area classification. Bureau of Mines personnel made an economic appraisal of mineral deposits by searching pertinent geological and mining publications as well as U.S. Bureau of Land Management, U.S. Forest Service, and U.S. Bureau of Mines files and records. Known mines, prospects, and mineralized localities were examined during 1981, and sampling and mapping were done where warranted. The Geological Survey 'did geologic mapping, geochemical sampling, and geophysical surveys to aid this study.

Jan 1, 1983

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

By A. Erickson

The effectiveness of a loader-mounted fan on diesel vehicles combined with natural convection for ventilation of a dead heading (the patented Janelid system) was investigated experimentally. The results were obtained using CO2 as a tracer gas in a 1/4 scale model heading. Buoyant forces were scaled to establish similarity with full scale. For a loader moving in a typical load-haul-dump cycle, the loader-mounted fan reduced the tracer gas concentration by 26 percent compared with a reduction of 32 percent for a jet fan of four times the flow capacity.

Jan 1, 1981

By Steven R. Munts

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the South Providence Wilderness Study Area (WSA) in 1982. No mines are currently operating in the WSA, however, the Golden Gift Mine in the southeastern part of the WSA produced $6,800 1/ worth of gold and silver and five mines adjacent to the east boundary of the WSA had a total production of about $3,500,000 1/ in gold, silver, lead, and copper. There is no recorded placer gold production. Over 350 lode and placer mining claims are in and immediately adjacent to the WSA. Of these, 74 were actively held (1982) and at least one area, which is partly within the northeast portion of the WSA, was being actively explored by private industry in 1982. Adjacent to the southeastern border of the WSA the Big Horn Mine contains an estimated 200,000 tons of indicated and inferred marginal reserves averaging 0.25 oz/ton gold; and the Hidden Hill Mine has 550 tons of subeconomic resources averaging 0.60 oz/ton gold. An additional 11,000 tons of marginally economic gold-bearing dump reserves average 0.17 oz/ton gold at the Bighorn, Hidden Hill, and the Buena Vista Mines and the Midas Touch Prospect. Sample analyses indicate eight mines and prospects in, and five adjacent to the WSA may have additional gold-silver-lead-copper vein-type resources. Five of these prospect areas may have a disseminated gold resource and one may have gold resources in a skarn. One prospect may have a porphyry-type copper-molybdenum resource. Although gold placer claims were filed sporadically throughout the WSA, none appears to have placer gold resources. Likelihood for mining is greatest at the Big Horn Mine; if a mill is built there, it could process Big Horn Mine ore, ore from the Hidden Hill Mine, and gold-bearing dumps at the Big Horn, Hidden Hill, and Buena Vista Mines and the Midas Touch Prospect. All of these resources are adjacent to the WSA; however, their development would increase likelihood for development of resources in the WSA. Two major fault zones (the Hidden Hill, and the Big Horn) appear to have controlled the mineralization at many of the prospects and mines. All of the prospects or mines with vein-type occurrences and resources are on or adjacent to one of these fault zones. Veins throughout the eastern half of the WSA contain various amounts of gold, silver, and copper; only veins near the Big Horn Mine and in the northeastern corner of the WSA contain lead. Some veins are as thick as 6 ft, are traceable intermittently for over 2 mi along strike, are sporadically mineralized, are encased in prophylitic, argillic, and phyllic altered host rock, contain pyrite, chalcopyrite, galena, specularite, barite, or fluorite, and display multiple stages of quartz veining and (or) brecciation. Sample analyses at five prospects (map nos. 3, 18, 23, 24, and 31) indicate they may have disseminated gold resources. To date no oil or gas has been discovered within the WSA. However, some oil and gas leases are currently (August 1982) held within this study area.

Jan 1, 1984

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Howard B. Hamilton

Laboratory performance of mercury filled current limiting devices (CLD) used for high speed switching of DC circuits (600 volts and below, up to 1000 amperes) using a system involving a parallel connected vacuum switch with CLD and an additional series connected vacuum switch was verified in USBM Contract #HO 357079. This report details analytical work and field experimental tests to predict and control voltage surges associated with the high switching speed associated with the switching system. It also details tests conducted to demonstrate the fault current limiting ability of the CLD. Problems associated with designing a fault current limiting system are discussed.

Jan 1, 1978

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

Coal, America's most abundant fossil fuel, is expected to play a key role in our pursuit of energy independence. A substantial increase in coal exploitation will be required if we are to fulfill our future energy needs. It is essential that new developments continue if stable coal prices are to be achieved and maintained. The challenge of the mining industry is to continue these developments in the face of problems related to increasing labor costs, inflation and environmental restoration. With expectations of increased activity in surface coal mining, the U.S. Bureau of Mines has authorized this study to determine the preliminary economic and technologic feasibility of underspoil haulage in area strip coal mines and to identify geologic and geographic areas where such a system could be used. These objectives were met by literature search, data-gathering visits to several active area strip mines and by analyzing various haulage systems that were superimposed on three model mines. Potential advantages of such a system include: 1) improved mine design; 2) lower mine operating costs; 3) improved land reclamation; 4) lower manpower requirements; 5) lower mobile equipment requirements; and 6) smaller, less sophisticated maintenance facilities.

Jan 1, 1975

By Jesse L. Hoyer

A Bureau of Mines turbomill was evaluated for use in the production of high-purity, ultrafine x-Sic powders suitable for advanced ceramics that could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. The effect of milling param-eters, such as type of dispersant, temperature, pH, and gas environment, on the milling of x-SiC was studied. The addition of dispersants improved the grindability of x-SiC. Of the six dispersants studied, the best results were obtained with Mara-sperse N-22. Grinding efficiency was also increased when the x-SiC was milled in a basic slurry and at elevated temperature. Gas environments did not appear to affect grinding of x-SiC. Optimum grinding efficiency was obtained at 50° C in a slurry at pH 9.5 with Marasperse N-22 as the dispersant. Under these conditions, minus 100-plus 200-mesh x-SiC was ground to 80 pct less than 1 um in 4 h.

Jan 1, 1987

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953