Search Documents

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972

By E. L. Singleton

The Bureau of Mines investigated extraction of aluminum from aluminum-silicon alloys as a means of utilizing domestic aluminum silicate ores for aluminum production. Aluminum was extracted from aluminum-silicon alloys by electrolysis in molten electrolytes of NaCl-KCI-AIC13 and NaCl-KCI-AIF3 in a laboratory-scale cell. Six alloys with aluminum contents ranging from 20 to 87 percent aluminum were tested, and aluminum products of primary grade or better were obtained. More than 80 percent of the aluminum was recovered with current efficiencies as high as 91 percent. Recovery of a metallurgical-grade silicon product from the anode residue by an acid leaching procedure was possible with the 50-50 and 65-35 Al-Si alloys.

Jan 1, 1972

By William R. Archibald

This report presents the results of a program demonstrating the technical and economic feasibility of hydraulic borehole mining of uraniferous sandstone. This mining technique involves the drilling of a borehole from the surface down into the ore body. A borehole mining tool consisting of a high-pressure cutting jet and a slurry jet pump is lowered down the borehole. Water from the high-pressure cutting jet cuts into the sandstone formation generating a water-sand slurry which flows to the slurry jet pump and is pumped to the surface. The cutting jet is rotated and moved up and down from the surface, thereby generating a cavity in the formation. When the cavity size reaches a point beyond the effective radius of the cutting jet, the mining tool is moved to an adjacent borehole and the process is started again. This program was carried out in four phases. Phase I included modifications to the borehole mining system (built and tested under a previous contract, No. H0252007, for the mining of coal) and factory tests of the jetting system. Phase II covered the field tests and a public demonstration. Phase III involved nozzle and equipment modifications and factory tests. Field testing continued under Phase IV along with an evaluation of this method. The field tests were conducted successfully on Rocky Mountain Energy Company's Nine Mile Lake property near Casper, Wyoming. Results indicate that; hydraulic borehole mining of uranium is technically feasible (300 tons of uraniferous sandstone were mined from a depth of 90 ft) and the hydraulic borehole method is economically attractive. However, additional testing is required to clearly define the economic feasibility.

Jan 1, 1978

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By Fredrick L. Johnson

The Bureau of Mines, under Congressional mandate, conducted a mineral survey on the Park Range WSA (Wilderness Study Area) in 1984 and 1985. The WSA, located about midway between Tonopah and Ely, encompasses 47,268 acres. No mineral resources were delineated, nor were workings found, during the investigation. There has been, however, exploration in and near the north end of the study area. ASARCO is actively exploring a block of 41 claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block is almost entirely in the study area. The Morey mining district, 7 miles southwest of the study area, produced silver and lesser amounts of gold and lead sporadically from the mid-1860's through the mid-1960's. The WSA is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. The Paleozoic rocks have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. Additional exploration in the north part of the Park Range WSA may lead to delineation of gold resources.

Jan 1, 1986

By R. L. Benner

The Bureau of Mines investigated the ZnO-Fe2O3-Fe3O4 system at 1,000°, 1,300°, and 1,400° C, with oxygen pressures between 1.0 and lx10-4 atmospheres. The results, divided into the thermodynamic properties as related to the spinel structure, and the thermodynamic properties as related to zinc concentrate roasting, were used to calculate the activities of ZnO, Fe2O4, and Fe3O4 within the spinel solid solution region of the ternary system, and the pseudo-binary activities of ZnFe2O4 and Fe304. The activities of both systems show large positive deviations from Raoult's Law, especially at high Fe3O4 concentrations. The free energies, the enthalpies, and the entropies of mixing for the binary system were calculated from the binary activities, and the entropies of mixing were compared with two statistical models, one representing an ideal solution, and one representing the mixing of a normal with an inverse spinel. The binary entropy of mixing seemed to be better represented by the latter statistical model, indicating that the tetrahedral and octahedral cations of the reactants tend to remain in the product, even at the high temperatures of the study. This comparison also indicated that the cations of the components are the major contributing factors to the thermodynamic properties.

Jan 1, 1966

By Marting J. Gavin

The twentieth century has often been spoken of as the age of petroleum, and from many viewpoints it can be justly considered so. Certainly the petroleum industry is one of enormous importance to this country, industrially, financially, and economically. The United States, however, at present producing over 60 per cent of the world's total output of petroleum, is not producing petroleum at a sufficient rate to provide for its own domestic, consumption. For several years this country has been importing increasing quantities of crude and partly refined oils from Mexico, and has been drawing heavily on domestic stocks of petroleum. Production in the United States is increasing, but it is not increasing at the same average rate as domestic consumption, nor is it probable that in the future domestic production will increase sufficiently to satisfy the demands of domestic consumption, but on the contrary, in the opinion of those best qualified to know, the peak in the curve of domestic production of crude petroleum will be reached in a comparatively few years, whereas the consumption of petroleum and its product will increase at a continually growing rate. This country, then, must turn, and as the increasing imports from Mexico indicate, is turning to other sources than the crude petroleum, produced in this country to make up the deficit between domestic production and domestic consumption of petroleum and its products,

Jun 1, 1920

By Ross W. Smith

Microflotation and surface chemical studies were conducted on a chromite from the Stillwater Complex in Montana and on some of the minerals usually found to be associated with such chromites. Considering the chromite it was found that aging the ground mineral in air or heating it markedly affected its flotation behavior. Much of the observed effects could be attributed to oxidation reactions involving surface chromium and iron species. Strongly acid pretreating the mineral appeared to reverse such effects. Thus, it can be concluded that the manner in which the mineral (or the ore) is pretreated is of utmost importance in its flotation. Work carried out on associated gangue minerals determined how they are likely to behave in a flotation environment and how certain foreign ions derived from a chromite ore itself can affect their surface characteristics and, thus, presumably also their behavior in a flotation circuit.

Jan 1, 1981

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By K. L. Erickson, Gerald A. Munson

"The need for spodumene as a source of lithia for war purposes led to the exploitation of the Edison pegmatite deposit 1-1/2 miles southeast of Keystone, S. Dak. The operation was conducted during 1943 and 1944 by the Lor Mining Co., Rapid City, S. Dak. Spodumene concentrates in the ratio of 15:1 were recovered by hand picking from a sorting belt. This method was expensive and wasteful of spodumene, owing to the small size of the crystals.Data4/ obtained by the Bureau of Mines indicates that blunging with hydroflouric acid or sodium hydroxide is a prerequisite to selective flotation. Results of tests by Denver Equipment Co., Denver, Colo., indicate that economic recoveries can be obtained in an alkaline circuit after desliming.At the request of the Lor Mining Co., K. L. Erickson, metallurgical engineer, was permitted to work in the pegmatite research laboratory to verify previous investigations and to determine problems that might be involved in commercial milling. The ensuing investigation indicated that electrolytes in the mill water produced a profound inhibiting action on the flotation of Edison spodumone.An investigation of mill water from various sources showed that some waters are suitable for the process and others are not. Subsequent testing showed that all of the available waters are suitable after treatment. The flotation of the Edison spodumene in an alkaline circuit after desliming and using oleic acid as collector is efficient and economical when the water does not contain impurities.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B.Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R. S. Dean, assistant director.As the work was of a practical nature, samples from possible mill-water sources in the southern Black Hills were obtained, and commercial softening and demineralizing methods were investigated. Data on various waters tested are given in table 1."

Jun 1, 1946

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932