Search Documents

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

By E. L. Rawlins

Systematic leakage surveys of natural-gas transmission lines not only aid in the conservation of gas, but can be made to show direct financial returns of large magnitude. 1. Such surveys reveal the actual leakage from the lines, and indicate repairs to be made in order, to eliminate unnecessary waste. 2. Tests on lines, after repairs are made, show the actual saving that has been accomplished. 3. Tests on newly constructed lines reveal the presence of leakage that should be eliminated before the lines are put into service.

Jan 1, 1926

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U. S. Department of the Interior, to stimulate greater interest in safety in the mineral-extractive industries and to encourage the development of more effective accident-prevention programs. Since its beginning in 1925, thirty-four safety contests have been conducted. This publication reports results of the 11 annual contests for the period 1948-1958, inclusive. Mineral operations awarded the "Sentinels of Safety" trophy for the best safety record in their competitive group as well as those ranking second, third, fourth, and fifth are listed along with a summary of their achievements in preventing disabling injuries. In addition, this publication contains statistical information reflecting the disabling work-injury experience of all other mines and quarries enrolled in the annual contests. The injury statistics of these operations are arranged in the six groups of the competition and through 1955 are the only data on injury-severity at noncoal mineral operations published by the Bureau of Hines. Recognition of the National Safety Competition in promoting safety has increased steadily during its 34 years. The number of plants participating in these annual competitions increased from 210 in 1925, its first year, to a record of 675 in 1958. The expanding scope of the National Safety Competition indicates that more mines and quarries in the United States are enrolling 90 all available means to promote safety on the job will be used. Safety contests like this are generally recognized, in the field of safety promotion, as an effective way to arouse and hold the interest of employees and officials in accident-prevention programs. They tend to forge individual precautionary acts into group action centered on a common objective, such as winning the ?Sentinels of Safety? trophy.

Jan 1, 1960

By Charles Findlay

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992

By E. L. Garton

[The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying; southwest of the Arbuckle Mountains. It includes six counties: Carter, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvania age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/ being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.]

Jan 1, 1941

By F. Fraas, J. E. Conley

"The problem of recovering potash from the mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O), occurring in large quantities in the salt beds of Texas and New Mexico, has been under investigation at the Nonmetallic Minerals Experiment Station of the U. S. Bureau of Mines continuously since 1928. Most of the results previously obtained have been published in technical journals and in a series of Bureau of Mines Reports of Investigations.The experiments described in the present report were performed to ascertain whether a continuous countercurrent extraction of calcined polyhalite by hot water would yield satisfactory recoveries and concentrations of sium sulphate in the top liquor. Previous investigation by Storch 4 had shown that the rate of solution of uncalcined polyhalite was too slow to be of value in an industrial process, and Storch and Clarke 5 had demonstrated that calcination of the polyhalite greatly, accelerated the rate of solution in hot water, allowing most of the potassium sulphate to be readily extracted."

Sep 1, 1933

By R. K. Koch

The vapor pressures of liquid titanium and liquid platinum were studied under the Bureau of Mines program for the determination of thermochemical data on the transition elements. Beating was done in a 2-kw electron-beam furnace with a water-cooled copper crucible to contain the melt. Temperature was measured with a disappearing-filament brightness pyrometer. The vapor pressure data for liquid titanium in the range 2,008° to 2,379° K are represented by the least-squares derived equation [log p (atm) = 6.268 - 22, T] Two series of determinations were made on liquid platinum. Results of the first series are expressed by the least-squares derived equation [log p (atm) = 8.240 - 30,460T] for the range 2,0860 to 2,4200 K. Results of the second series are expressed by the least-squares derived equation [log p (atm) = 7.795 - 29,580 T] in the range 2,045° to 2,442° K. Third-law evaluations of each series gave mean standard heats of sublimation of 112.4 kcal/mole, 133.3 kcal/mole, and 133.8 kcal/mole for titanium first series on platinum, and second series on platinum, respectively. Second-law heats of sublimation and equations for heats, free energies, and entropies of vaporization were obtained from sigma plots of each data set.

Jan 1, 1969

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973

By H. E. Peterson, W. L. Anderson

"INTRODUCTION The great demand for tungsten incident to the war has led to the exploration of a large number of low-grade tungsten deposits. To properly evaluate the low-grade deposits it is essential to have available a dependable method of analysis applicable to all types of low-grade tungsten ores. Results reported on the tungsten content of the ores have often varied quite widely and have led to confusion. The Bureau of Mines has been requested by Government lending agencies and by companies interested in the production of tungsten to publish a general method for the determination of tungsten in low-grade ores. To meet this need, the Bureau of Mines is herein submitting two methods for analysis that have been proved on a large number of tungsten-bearing ores various types in the Bureau of Mines laboratory in Salt Lake City. Also, a third method was developed that requires no cinchonine and has proved to be applicable on most tungsten ores. The cinchonine method is the generally accepted for analysis of tungsten ores. Very reliable results can be obtained by this method if certain precautions are taken, as outlined in this report."

May 1, 1943

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 1992