Search Documents

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By Lloyd M. Kniffin

[This paper is one of series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United States. It describes the mine of the Hanover Bessemer Iron & Copper Co. at Fierro, Grant County, N. M., which is the only operating iron mine in the southwestern part of the United States. This mine is in a district noted for the great variety of ores that it produces. Within a small area, as shown is Figure 1, there are noteworthy deposits of nearly all the common metals. The ore occurs in lenticular masses dipping at about 50°. An underhand stoping method has been developed that requires but a very small amount of handling of ore. As the ore is very irregular in iron content and also in the distribution of the impurities--chiefly sulphur, silica, and magnesia--a method has to be used that will permit selective mining and will also allow ore and waste to be taken out separately as conditions change. A magnetic cobbing plant raises the grade of the ore shipped about 10 per cent.]

Jan 1, 1930

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President's focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria's Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria's mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria's main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By James Westfield

This report covers the calendar year 1954 and has been prepared and submitted to the Congress of the United States in accordance with the provisions of Sec. 106(a) and Sec. 2l2(c) of the Federal Coal-Mine Safety Act (66 Stat. 692; 30 U.S.C. Sec. 451-483). Background The Federal Coal-Mine Inspection program was established to carry out the provisions of Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. This act has since been amended to be known as Title I -Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also includes Title II -Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal-Mine Safety Act.

Jan 1, 1956

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for the Philippines for the period from 1970 through 1981. The work was done through the Bureau of Mines, Minerals Availability Program, under Contract number J01225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) eimber and lumber, 6) fuel, 7) powder and balsting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines, describing mining methods and performance at individual mining operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and performance. Limestone deposits in Iowa are extensive and reserves are large. Most of the past production came from the eastern third of the state, although over half of the counties in the state have produced, or are now producing limestone. The stone is used as aggregate, road metal, agricultural lime, riprap, fluxing stone, railroad ballast, and in the manufacture of cement and lime.

Jan 1, 1962

By Harry R. Nicholls

The objectives of this investigation were to determine the strain propagation laws for a strain pulse in salt and to compare the seismic effects from the detonation of different explosives in salt. The investigation showed that a strain propagation law of the type, e = K(R/W 1/3 ) n, and a strain energy propagation law of the type, Ea/W 1/3 = K(R/WI/3)b , are valid in salt. A change in the regression law coefficient, n , was noted with strain level. A similar change in b was inferred because strain energy is proportional to the square of strain amplitude. Particle velocity data may be used interchangeably with strain data under the test conditions.

Jan 1, 1962

By H. S. Price

This report discusses the development of a mathematical model that describes the flow of methane only and methane and water in a coal bed during mining operations. Because of the complex geometry, boundary conditions and fluid properties, the model is based on a numerical solution to the equations describing flow. The goals for the development of this model and requirements to which it complies are for the most part expressly stated in Request for Proposal No. 50110752. In addition to the capabilities specified under the scope of work the model can handle an anisotropic porous medium and a source term has been added which will simulate, somewhat, the effects of desorption. This term will be pressure dependent. The effect of time on such a term is only taken care of in the change of pressure with time. This source term will have the dimensions of Mcf/day/Mcf pore volume. It will be a part of the input data to be supplied by the user and will be entered as a table of rates versus pressure. These models consider the fracture system as the main porosity. All computed results pertain to the fractures. The source term mentioned above represents the flow from the matrix porosity into the fracture. Such flow should be small compared with the flow between fractures since these models handle only one porosity structure system.

Jan 1, 2012

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962